Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › CAMSHAFT › 2012.12–2014.10
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046811 CAMSHAFT A

3ZR-FAE ENGINE MECHANICAL  CAMSHAFT  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the camshaft housing sub-assembly or camshaft timing gear assembly (intake or exhaust side).

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 13750 1.INSTALL VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 2.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 11103 3.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the camshaft housing sub-assembly.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A131901C14
2.167,0.781 2.458,0.542 2.458,0.542 2.594,0.531 false 1.771,0.49 1.604,0.25 1.604,0.25 1.479,0.25 false 1.167,1.073 0.906,0.938 0.906,0.938 0.792,0.938 false 2.073,1.125 2.479,1.417 2.479,1.417 2.604,1.417 false 0.583,0.854 0.896,1.01 0.313,0.156 10 *1 1.271,0.177 1.583,0.333 0.313,0.156 10 *2 2.646,1.344 2.958,1.5 0.313,0.156 10 *3 2.646,0.458 2.958,0.615 0.313,0.156 10 *4
*1 Valve Lash Adjuster Assembly
*2 Valve Rocker Arm Sub-assembly
*3 Valve Stem
*4 Valve Stem Cap


Make sure that the valve rocker arm is installed as shown in the illustration.


b.
A206178C02
1.885,2.333 1.885,2.844 1.885,2.844 2.063,2.844 true 0.417,2.896 0.573,3.073 0.156,0.177 10 A 0.417,0.281 0.573,0.458 0.156,0.177 10 B 2.115,2.771 2.427,2.927 0.313,0.156 10 *1
*1 Continuous Line


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard Seal Diameter:
Area Specified Condition
Continuous Line 3.5 to 4.5 mm (0.138 to 0.177 in.)
A 8.0 mm (0.315 in.)
B 7.0 mm (0.276 in.)


Application Length A and B:

15 mm (0.591 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




c.
A270927N01
0.354,1.344 0.667,1.542 0.313,0.198 10 14 0.563,1.344 0.875,1.542 0.313,0.198 10 17 0.958,1.396 1.271,1.594 0.313,0.198 10 8 1.427,1.406 1.74,1.604 0.313,0.198 10 2 1.885,1.396 2.198,1.594 0.313,0.198 10 5 2.313,1.406 2.625,1.604 0.313,0.198 10 11 0.063,2.146 0.375,2.344 0.313,0.198 10 13 1.177,1.969 1.49,2.167 0.313,0.198 10 7 1.667,1.979 1.979,2.177 0.313,0.198 10 1 2.104,1.969 2.417,2.167 0.313,0.198 10 4 2.573,1.979 2.885,2.177 0.313,0.198 10 10 2.854,2.188 3.167,2.385 0.313,0.198 10 16 0.365,3.156 0.677,3.354 0.313,0.198 10 15 0.979,3.104 1.292,3.302 0.313,0.198 10 9 1.406,3.104 1.719,3.302 0.313,0.198 10 3 1.875,3.104 2.188,3.302 0.313,0.198 10 6 2.344,3.104 2.656,3.302 0.313,0.198 10 12

Set the camshaft and No. 2 camshaft as shown in the illustration.


d.

Install the camshaft housing sub-assembly with the 17 bolts and tighten them in the order shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:
·

After installing the camshaft housing sub-assembly, make sure that the cam lobes are positioned as shown in the illustration.

·

If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly, clean the installation surfaces, and reapply seal packing.

·

If the camshaft housing sub-assembly is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.

·

After installing the camshaft housing sub-assembly, wipe off any seal packing that seeped out from between the camshaft housing sub-assembly and cylinder head sub-assembly.




Hide 13070A 4.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the camshaft timing exhaust gear assembly.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A215318C08
1.458,1.021 1.01,0.156 1.01,0.156 0.792,0.156 true 1.156,1.031 0.573,1.656 0.573,1.656 0.406,1.656 true 0.552,0.083 0.865,0.24 0.313,0.156 10 *1 0.198,1.573 0.51,1.729 0.313,0.156 10 *2
*1 Straight Pin
*2 Pin Hole


Put the camshaft timing exhaust gear assembly and camshaft together by aligning the pin hole and straight pin.

NOTICE:

Do not forcefully push in the camshaft timing exhaust gear assembly. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing exhaust gear assembly.



b.

Lightly press the camshaft timing exhaust gear assembly against the camshaft and turn the camshaft timing exhaust gear assembly. Push further at the position where the pin enters the hole.

NOTICE:

Be sure not to turn the camshaft timing exhaust gear assembly in the retard direction (clockwise).



c.
A146267C19
1.917,0.74 1.813,0.74 1.813,0.74 1.427,1.031 false 1.49,0.177 1.292,0.177 1.292,0.177 1.031,0.906 false 1.521,0.104 1.833,0.26 0.313,0.156 10 *1 1.969,0.667 2.281,0.823 0.313,0.156 10 *2 1.292,0.479 1.604,0.635 0.313,0.156 10 *a 1.25,1.854 1.563,2.01 0.313,0.156 10 *b
*1 Camshaft Timing Exhaust Gear Assembly
*2 Camshaft Flange
*a Clearance
*b No Clearance


Check that there is no clearance between the camshaft timing exhaust gear assembly and camshaft flange.


d.
A165297

Tighten the flange bolt with the camshaft timing exhaust gear assembly secured in place.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


e.

Check the camshaft timing exhaust gear assembly lock.

i.

Make sure that the camshaft timing exhaust gear assembly is locked.



Hide 13050 5.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A146265C15
2.247,0.475 2.424,0.657 0.177,0.182 10 *1 1.66,0.259 1.837,0.441 0.177,0.182 10 *2 2.217,0.553 2.097,0.553 2.097,0.553 1.965,1.087 false 1.629,0.343 1.51,0.343 1.51,0.343 1.328,1.019 false
*1 Straight Pin
*2 Key Groove


Put the camshaft timing gear assembly and camshaft together with the straight pin and key groove misaligned as shown in the illustration.

NOTICE:

Do not forcefully push in the camshaft timing gear assembly. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing gear assembly.



b.
A270928C01
0.813,1.396 1,1.917 1,1.917 1.167,1.917 true 0.802,0.583 0.802,0.167 0.802,0.167 0.969,0.167 true 1.01,0.063 1.323,0.219 0.313,0.156 10 *1 1.208,1.833 1.521,1.99 0.313,0.156 10 *2 0.208,0.333 0.521,0.49 0.313,0.156 10 *a 2.583,0.708 2.896,0.865 0.313,0.156 10 *a
*1 Straight Pin
*2 Key Groove
*a View A


Turn the camshaft timing gear assembly as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the straight pin fits into the key groove.

NOTICE:

Do not turn the camshaft timing gear assembly in the retard direction (clockwise).



c.
A146267C19
1.917,0.74 1.813,0.74 1.813,0.74 1.427,1.031 false 1.49,0.177 1.292,0.177 1.292,0.177 1.031,0.906 false 1.521,0.104 1.833,0.26 0.313,0.156 10 *1 1.969,0.667 2.281,0.823 0.313,0.156 10 *2 1.292,0.479 1.604,0.635 0.313,0.156 10 *a 1.25,1.854 1.563,2.01 0.313,0.156 10 *b
*1 Camshaft Timing Gear Assembly
*2 Camshaft Flange
*a Clearance
*b No Clearance


Check that there is no clearance between the camshaft timing gear assembly and camshaft flange.


d.
A165296

Tighten the flange bolt with the camshaft timing gear assembly secured in place.

Torque:
54 N*m (551 kgf*cm, 40 ft.*lbf)


e.
A165299C04
0,2.094 0.146,2.177 0.146,0.083 10 _
V100135

Lock


Check that the camshaft timing gear assembly can move in the retard direction (clockwise) and is locked in the most retarded position.


Hide 13506 6.INSTALL CHAIN SUB-ASSEMBLY