Home › Engine / Hybrid System › 3ZR-FAE LUBRICATION › OIL PUMP › 2012.12–2015.04
RM3090E _51 Engine / Hybrid System _008392 3ZR-FAE LUBRICATION _0046846 OIL PUMP A

3ZR-FAE LUBRICATION  OIL PUMP  INSTALLATION  


PROCEDURE

Hide 15100 1.INSTALL OIL PUMP ASSEMBLY

a.

Install the oil pump with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 12102A 2.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

a.
A150920C03
3.156,2.042 3.156,1.896 3.156,1.896 2.917,1.688 false 0.896,2.375 1.063,2.375 1.063,2.375 1.156,2.656 false 2.073,2.292 2.24,2.292 2.24,2.292 2.313,2.615 false 0.24,1.385 0.469,1.604 0.229,0.219 10 A 0.25,0.99 0.479,1.208 0.229,0.219 10 B 0.865,0.99 1.094,1.208 0.229,0.219 10 B 0.865,1.385 1.094,1.604 0.229,0.219 10 A 0.563,3.052 0.927,3.26 0.365,0.208 10 A - A 1.865,3.052 2.219,3.24 0.354,0.188 10 B - B 3.083,2.083 3.302,2.26 0.219,0.177 10 *1 0.677,2.271 0.885,2.448 0.208,0.177 10 *b 1.865,2.177 2.031,2.354 0.167,0.177 10 *a
*1 Seal Packing
*a 3.0 to 4.5 mm (0.118 to 0.177 in.)
*b 6.0 mm (0.236 in.)


Remove any old packing material and be careful not to drop any oil on the contact surfaces of the stiffening crankcase and No. 2 oil pan sub-assembly.


b.

Apply seal packing in a continuous line as shown in the illustration.

Application Specification:
Area Seal Packing Diameter Distance from Center of Bolt Hole to Center of Seal Packing
A - A 3.0 to 4.5 mm (0.118 to 0.177 in.) 6.0 mm (0.236 in.)
B - B -


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the No. 2 oil pan sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add engine oil for at least 2 hours after installing the No. 2 oil pan.




c.

Install the No. 2 oil pan sub-assembly with the 10 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13507 3.INSTALL NO. 2 CHAIN SUB-ASSEMBLY

a.
A206151

Temporarily install the crankshaft pulley bolt.


b.

Set the crankshaft key as shown in the illustration.


c.

Turn the drive shaft so that the cutout faces upward.


d.

Remove the crankshaft pulley bolt.


e.
A296326C01
1.5,1.802 1.083,1.583 1.083,1.583 0.917,1.583 false 1.594,1.927 2.177,2.094 2.177,2.094 2.344,2.094 true 1.906,4.167 2.125,4.417 2.125,4.417 2.25,4.417 false 1.844,3.438 2.333,3.083 2.333,3.083 2.583,3.083 true 1.75,2.417 2.198,2.667 2.198,2.667 2.417,2.667 true 1.177,3.844 1.396,3.844 1.396,3.844 1.844,4.01 true 0.958,3.76 1.167,3.958 0.208,0.198 10 *1 2.385,2 2.583,2.198 0.198,0.198 10 *1 0.729,1.448 0.927,1.646 0.198,0.198 10 *2 2.302,4.344 2.49,4.521 0.188,0.177 10 *2 2.469,2.583 2.656,2.771 0.188,0.188 10 *3 2.615,3 2.813,3.198 0.198,0.198 10 *4
*1 Timing Mark
*2 Mark Plate (Yellow)
*3 Oil Pump Drive Gear
*4 Oil Pump Drive Shaft Gear
V100135

Front


Align the yellow mark plates with the timing mark of each gear as shown in the illustration.


f.

Install the gears onto the crankshaft and oil pump shaft with the chain on the gears.


g.

Temporarily install the oil pump drive shaft gear with the nut.


h.

Install the chain damper spring to the chain tensioner plate, and then install the chain tensioner plate with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


i.
A206155E01
0.337,0.148 0.66,0.325 0.323,0.177 10 SST 0.724,0.216 0.87,0.216 0.87,0.216 1.48,0.474 false 1.189,0.587 0.87,0.216 false

Temporarily install the crankshaft pulley with the pulley bolt.


j.

Using SST, hold the crankshaft. Then tighten the drive shaft gear nut.

for 86 mm (3.39 in.) Bolt Pitch Type:

SST
09213-58014  (91551-80840)
09330-00021  

for 64 mm (2.52 in.) Bolt Pitch Type:

SST
09213-54015  09330-00021  

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)

HINT:

For the 64 mm (2.52 in.) bolt pitch type, the part number of the installationbolt for SST (crankshaft pulley holding tool) is 91551-00850 (quantity: 2).



k.

Remove SST, the crankshaft pulley bolt and the crankshaft pulley.


Hide 13521 4.INSTALL CRANKSHAFT TIMING SPROCKET

a.
A206150C02
2.698,1.177 2.917,1.365 0.219,0.188 10 *a
*a Front


Install the crankshaft timing sprocket as shown in the illustration.


Hide 13561 5.INSTALL NO. 1 CHAIN VIBRATION DAMPER

Hide 6.SET NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 13559 8.INSTALL CHAIN TENSIONER SLIPPER

Hide 9.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

Hide 11302 10.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

a.

Install a new gasket.

NOTICE:

Remove any oil from the contact surface.



b.

Install the engine water pump assembly with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head, camshaft housing, stiffening crankcase and cylinder block.

A301122C01
2.292,1.49 2.302,1.49 false
V100145

Clean and Degrease - -



d.

Install 3 new O-rings.


e.

Apply seal packing as shown in the illustration.

A302701C01
2.677,1.208 2.833,1.406 0.156,0.198 10 false A 0.688,1.219 0.844,1.417 0.156,0.198 10 false A 4.458,1.146 4.615,1.344 0.156,0.198 10 false A 5.094,2.24 5.302,2.438 0.208,0.198 10 false *a
*a 5.0 mm (0.197 in.) - -


Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal diameter:

5.0 mm (0.197 in.)


NOTICE:
·

Remove any oil from the contact surface.

·

Install the timing chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

Do not add engine oil for at least 2 hours after installing the timing chain cover sub-assembly.




f.

Apply seal packing to the timing chain cover sub-assembly in a continuous line as shown in the following illustration.

A296857C01
2.26,2.031 2.385,2.031 2.385,2.031 2.531,1.781 false 4.646,2.177 4.49,2.177 4.49,2.177 4.365,1.802 false 3.375,5.219 3.719,5.438 3.719,5.438 3.927,5.438 false 1.354,5.26 1.771,5.417 1.771,5.417 1.927,5.417 false 5.344,5.26 5.625,5.375 5.625,5.375 5.781,5.375 false 4.833,1.125 4.979,1.292 0.146,0.167 10 J 2.188,2.208 2.333,2.375 0.146,0.167 10 O 6.25,2.115 6.396,2.281 0.146,0.167 10 M 1.51,1.156 1.656,1.323 0.146,0.167 10 F 0.563,3.948 0.708,4.115 0.146,0.167 10 I 0.823,2.042 0.969,2.208 0.146,0.167 10 H 6.583,3.979 6.729,4.146 0.146,0.167 10 N 5.229,1.917 5.375,2.083 0.146,0.167 10 K 5.74,2.073 5.885,2.24 0.146,0.167 10 L 2.135,1.01 2.281,1.177 0.146,0.167 10 A 2.781,0.708 2.927,0.875 0.146,0.167 10 A 1.188,1.938 1.333,2.104 0.146,0.167 10 G 2.104,1.938 2.25,2.104 0.146,0.167 10 D 4.688,2.083 4.833,2.25 0.146,0.167 10 E 5.542,7.396 5.688,7.563 0.146,0.167 10 B 2.156,7.094 2.302,7.26 0.146,0.167 10 B 1.479,7.396 1.625,7.563 0.146,0.167 10 B 4.875,7.094 5.021,7.26 0.146,0.167 10 B 2.167,7.833 2.313,8 0.146,0.167 10 C 1.438,7.833 1.583,8 0.146,0.167 10 C 4.729,7.677 4.875,7.844 0.146,0.167 10 C 5.583,7.865 5.729,8.031 0.146,0.167 10 C 4.677,8.115 4.823,8.281 0.146,0.167 10 B 5.323,8.469 5.469,8.635 0.146,0.167 10 B 0.969,6.313 1.115,6.479 0.146,0.167 10 D 4.292,6.344 4.438,6.51 0.146,0.167 10 E 0.729,4.99 1.104,5.167 0.375,0.177 10 A - A 2.688,4.906 3.063,5.083 0.375,0.177 10 B - B 4.656,4.896 5.031,5.073 0.375,0.177 10 C - C 3.635,4.906 3.833,5.073 0.198,0.167 10 *c 1.625,4.979 1.823,5.146 0.198,0.167 10 *a 1.969,5.323 2.167,5.49 0.198,0.167 10 *b 5.604,4.927 5.802,5.094 0.198,0.167 10 *e 5.833,5.271 6.031,5.438 0.198,0.167 10 *f 3.958,5.333 4.156,5.5 0.198,0.167 10 *d
*a 2.5 mm (0.0984 in.) *b 2.5 to 3.5 mm (0.0984 to 0.138 in.)
*c 5.0 mm (0.197 in.) *d 4.5 to 5.5 mm (0.177 to 0.217 in.)
*e 7.5 mm (0.295 in.) *f 7.0 to 8.0 mm (0.276 to 0.315 in.)


Seal Packing:
Item Seal Packing
Dashed line Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
Continuous line
Alternate long and short dashed line Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent


Application Specification:
Area Seal Packing Diameter Distance from Edge of Cover to: Seal Packing Application Length Distance from Top of Cover to Top of Seal Packing
Dashed line 2.5 to 3.5 mm (0.0984 to 0.138 in.) Center of seal packing
2.5 mm (0.0984 in.)
- -
Continuous line 4.5 to 5.5 mm (0.177 to 0.217 in.) or 7.0 to 8.0 mm (0.276 to 0.315 in.) - - -
Alternate long and short dashed line 4.0 mm (0.157 in.) Center of seal packing
3.0 mm (0.118 in.)
- -
A - A 2.5 to 3.5 mm (0.0984 to 0.138 in.) Center of seal packing
2.5 mm (0.0984 in.)
- -
B - B 4.5 to 5.5 mm (0.177 to 0.217 in.) Opposite edge of seal packing
5.0 mm (0.197 in.)
- -
C - C 7.0 to 8.0 mm (0.276 to 0.315 in.) Opposite edge of seal packing
7.5 mm (0.295 in.)
- -
F 4.5 to 5.5 mm (0.177 to 0.217 in.) - 15.8 mm (0.622 in.) 50.1 mm (1.97 in.)
G 4.5 to 5.5 mm (0.177 to 0.217 in.) - 10.3 mm (0.406 in.) 155.1 mm (6.11 in.)
H 7.0 to 8.0 mm (0.276 to 0.315 in.) - 19.5 mm (0.768 in.) 165.4 mm (6.51 in.)
I 4.5 to 5.5 mm (0.177 to 0.217 in.) - 14.6 mm (0.575 in.) 397.8 mm (1.31 ft.)
J 4.5 to 5.5 mm (0.177 to 0.217 in.) - 18.6 mm (0.732 in.) 51.4 mm (2.02 in.)
K 4.5 to 5.5 mm (0.177 to 0.217 in.) - 25.3 mm (0.996 in.) 133.9 mm (5.27 in.)
L 7.0 to 8.0 mm (0.276 to 0.315 in.) - 25.8 mm (1.02 in.) 159.2 mm (6.28 in.)
M 4.5 to 5.5 mm (0.177 to 0.217 in.) - 5.0 mm (0.197 in.) 185.0 mm (7.28 in.)
N 4.5 to 5.5 mm (0.177 to 0.217 in.) - 14.6 mm (0.575 in.) 397.8 mm (1.31 ft.)
O 4.0 mm (0.157 in.) Center of seal packing
3.0 mm (0.118 in.)
- -


NOTICE:
·

When the contact surfaces are wet, wipe them with oil-free cloth before applying seal packing.

·

Install the timing chain cover within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

·

After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket and oil filter bracket within 10 minutes.

·

Do not add engine oil for at least 2 hours after installation.




g.

Clean the bolts and their installation holes.


h.

Install the timing chain cover.


i.

Temporarily install the engine mounting bracket with the 3 bolts.

NOTICE:
·

Install the mounting bracket within 10 minutes after installing the timing chain cover sub-assembly.

·

Do not add engine oil for at least 2 hours after installation.




j.

Install 2 new O-rings.


k.

Temporarily install the oil filter bracket with the 4 bolts.

NOTICE:
·

Install the oil filter bracket within 10 minutes after installing the timing chain cover sub-assembly.

·

Do not add engine oil for at least 2 hours after installation.




l.

Apply adhesive to 5 and a half threads or more of the end of bolt E.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



m.

Install the timing chain cover with the 26 bolts and seal washer in the order shown in the illustration.

A296897C01
1.99,1.844 2.281,1.344 2.281,1.344 3.031,1.344 true 0.833,0.885 0.969,1.042 0.135,0.156 10 A 0.99,1.677 1.125,1.833 0.135,0.156 10 A 0.99,2.042 1.125,2.198 0.135,0.156 10 A 1,2.344 1.135,2.5 0.135,0.156 10 A 1.01,2.698 1.146,2.854 0.135,0.156 10 A 1.219,2.896 1.354,3.052 0.135,0.156 10 A 1.229,3.188 1.365,3.344 0.135,0.156 10 A 1.781,3.26 1.917,3.417 0.135,0.156 10 A 2.073,3.458 2.208,3.615 0.135,0.156 10 A 2.594,2.969 2.729,3.125 0.135,0.156 10 A 2.656,2.656 2.792,2.813 0.135,0.156 10 A 2.698,2.26 2.833,2.417 0.135,0.156 10 A 2.646,2.042 2.781,2.198 0.135,0.156 10 A 3.271,2.167 3.406,2.323 0.135,0.156 10 A 2.833,1.792 2.969,1.948 0.135,0.156 10 A 2.01,2.01 2.146,2.167 0.135,0.156 10 A 1.927,1.417 2.063,1.573 0.135,0.156 10 D 0.958,1.427 1.094,1.583 0.135,0.156 10 B 0.865,1.104 1,1.26 0.135,0.156 10 B 0.771,0.646 0.906,0.802 0.135,0.156 10 E 1.99,0.625 2.125,0.781 0.135,0.156 10 C 2.958,0.646 3.094,0.802 0.135,0.156 10 E 2.917,0.917 3.052,1.073 0.135,0.156 10 C 2.792,1.167 2.927,1.323 0.135,0.156 10 B 2.688,1.354 2.823,1.51 0.135,0.156 10 B 2.677,1.552 2.813,1.708 0.135,0.156 10 C 3.083,1.25 3.396,1.448 0.313,0.198 10 *1 5.135,0.635 5.333,0.802 0.198,0.167 10 20 5.844,1.552 6.042,1.719 0.198,0.167 10 21 4.135,2.698 4.333,2.865 0.198,0.167 10 22 4.354,3.208 4.552,3.375 0.198,0.167 10 23 4.927,3.26 5.125,3.427 0.198,0.167 10 25 4.344,2.917 4.542,3.083 0.198,0.167 10 24 5.813,2.677 6.01,2.844 0.198,0.167 10 10 5.76,2.969 5.958,3.135 0.198,0.167 10 11 5.219,3.458 5.417,3.625 0.198,0.167 10 12 4.115,2.375 4.313,2.542 0.198,0.167 10 13 4.104,2.042 4.302,2.208 0.198,0.167 10 14 4.094,1.688 4.292,1.854 0.198,0.167 10 15 3.948,0.885 4.146,1.052 0.198,0.167 10 16 3.875,0.656 4.073,0.823 0.198,0.167 10 17 5.063,1.417 5.26,1.583 0.198,0.167 10 18 6.063,0.917 6.26,1.083 0.198,0.167 10 19 5.844,1.354 5.969,1.521 0.125,0.167 10 1 4.135,1.417 4.26,1.583 0.125,0.167 10 2 5.958,1.167 6.083,1.333 0.125,0.167 10 3 4.042,1.094 4.167,1.26 0.125,0.167 10 4 6.115,0.656 6.24,0.823 0.125,0.167 10 5 5.188,2.021 5.313,2.188 0.125,0.167 10 6 6.01,1.802 6.135,1.969 0.125,0.167 10 7 5.792,2.042 5.917,2.208 0.125,0.167 10 8 5.875,2.24 6,2.406 0.125,0.167 10 9 6.427,2.177 6.625,2.344 0.198,0.167 10 26 0.406,0.115 0.635,0.302 0.229,0.188 10 *a 3.698,0.104 3.927,0.292 0.229,0.188 10 *b
*1 Seal Washer - -
*a Torque Specification *b Bolt Tightening Order


Torque:
for bolt A, E : 25.5 N*m (260 kgf*cm, 19 ft.*lbf)
for bolt B : 51 N*m (520 kgf*cm, 38 ft.*lbf)
for bolt C : 51 N*m (520 kgf*cm, 38 ft.*lbf)
for bolt D : 10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:
·

When the contact surfaces are wet, wipe them with oil-free cloth before applying seal packing.

·

Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying the seal packing.

·

Do not add engine oil for at least 2 hours after installation.



Bolt Length:
Item Length Thread Diameter
Bolt A, E 35 mm (1.38 in.) 8 mm (0.315 in.)
Bolt B 55 mm (2.17 in.) 10 mm (0.394 in.)
Bolt C 80 mm (3.15 in.) 10 mm (0.394 in.)
Bolt D 40 mm (1.57 in.) 6 mm (0.236 in.)


HINT:

Apply adhesive to bolt E before installing it.



Hide 11302A 11.INSTALL TIMING CHAIN COVER OIL SEAL

Hide 15620 12.INSTALL OIL FILTER CAP ASSEMBLY

Hide 13.INSTALL ENGINE MOUNTING BRACKET STUD BOLT

Hide 13540 15.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

Hide 11213 16.INSTALL CYLINDER HEAD COVER GASKET

Hide 11201 17.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12551A 18.INSTALL NO. 1 VACUUM PUMP BRACKET

Hide 29300 19.INSTALL VACUUM PUMP ASSEMBLY

Hide 16267 25.CONNECT NO. 3 WATER BY-PASS HOSE

Hide 17167 29.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11452 30.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

Hide 23250 31.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23807V 32.INSTALL NO. 1 DELIVERY PIPE SPACER

Hide 23807 33.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23901 34.INSTALL FUEL TUBE SUB-ASSEMBLY

Hide 35.INSTALL WIRE HARNESS CLAMP BRACKET

Hide 22210 38.INSTALL THROTTLE BODY ASSEMBLY

Hide 40.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE