Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › ENGINE UNIT › 2012.12–2014.10
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046816 ENGINE UNIT A

3ZR-FAE ENGINE MECHANICAL  ENGINE UNIT  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove a stiffening cranckcase ring pin unless it is being replaced.


A152991C09
0.64,2.03 0.804,2.198 0.164,0.169 10 *2 1.31,2.665 1.49,2.818 0.18,0.153 10 *3 3.014,2.376 3.188,2.535 0.174,0.16 10 *1
*1 Protrusion Height
*2 Width
*3 Height


a.

Using a plastic-faced hammer, tap in 2 new stiffening cranckcase ring pins until they stop.

Standard Ring Pin:
Protrusion Height Height Width
3.0 mm (0.118 in.) 11 mm (0.433 in.) 8.0 mm (0.315 in.)



Hide 2.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or the threads are damaged, replace it.


a.
A150942C07
2.667,2.104 2.5,2.104 2.5,2.104 2.333,1.771 true 0.417,1.948 0.583,1.948 0.583,1.948 0.75,1.615 true 2.25,2.75 2.708,2.927 0.458,0.177 10 false *b 1.625,2.688 1.792,2.917 0.167,0.229 10 false *a 1.615,3.01 1.927,3.229 0.313,0.219 10 false *a 2.708,2.021 3.021,2.177 0.313,0.156 10 false *1 0.26,1.885 0.573,2.042 0.313,0.156 10 false *1
*1 Stud Bolt
*a 9.0 mm (0.354 in.)
*b 19 mm (0.748 in.)


Using an E6 "TORX" socket wrench, install the stud bolts as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


b.
A150941C03
2.688,2.656 2.896,2.865 0.208,0.208 10 *c 2.26,2.365 2.479,2.542 0.219,0.177 10 *a 2.25,2.938 2.448,3.125 0.198,0.188 10 *b
*a 15 mm (0.591 in.)
*b 12 mm (0.472 in.)
*c 34 mm (1.34 in.)


Using an E5 "TORX" socket wrench, install the stud bolts as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


c.
A298932C01
1.51,2.5 1.823,2.656 0.313,0.156 10 *a 1.542,3.01 1.854,3.167 0.313,0.156 10 *b 2.479,2.719 2.792,2.875 0.313,0.156 10 *c
*a 12 mm (0.472 in.)
*b 9.0 mm (0.354 in.)
*c 23 mm (0.906 in.)


Using an E5 "TORX" socket wrench, install the stud bolts as shown in the illustration.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.
A173608C01
0.958,3.719 1.24,3.938 0.281,0.219 10 *a 1.698,3.438 1.927,3.656 0.229,0.219 10 *b 1.385,4.042 1.583,4.229 0.198,0.188 10 *c
*a 12 mm (0.472 in.)
*b 18 mm (0.709 in.)
*c 48.5 mm (1.91 in.)


Using an E7 "TORX" socket wrench, install the camshaft housing stud bolts.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 11420 3.INSTALL STIFFENING CRANKCASE ASSEMBLY

a.
A150919C05
1.469,0.26 1.365,0.26 1.365,0.26 1.208,0.75 true 0.583,2.635 0.844,2.854 0.26,0.219 10 *a 1.5,0.177 1.813,0.333 0.313,0.156 10 *1
*1 Seal Packing
*a Area A


Apply seal packing in a continuous line as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three bond 1207B or equivalent


Standard Seal Diameter:
Area Specified Condition
except Area A 2.0 to 3.0 mm (0.0787 to 0.118 in.)
for Area A 4.5 to 5.5 mm (0.177 to 0.217 in.)


Application Length (Area A):

56 mm (2.20 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the stiffening crankcase assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.

·

Do not start the engine for at least 2 hours after installing the stiffening crankcase assembly.




b.
A152989N09
0.792,0.188 0.938,0.365 0.146,0.177 10 false B 1.344,0.198 1.49,0.375 0.146,0.177 10 false B 1.688,0.219 1.833,0.396 0.146,0.177 10 false B 2.167,0.302 2.313,0.479 0.146,0.177 10 false C 2.344,2.146 2.49,2.323 0.146,0.177 10 false C 1.802,2.146 1.948,2.323 0.146,0.177 10 false C 1.719,2.396 1.865,2.573 0.146,0.177 10 false 2 1.385,4.365 1.531,4.542 0.146,0.177 10 false 1 1.365,2.177 1.51,2.354 0.146,0.177 10 false C 0.979,2.188 1.125,2.365 0.146,0.177 10 false C 0.615,2.188 0.76,2.365 0.146,0.177 10 false C 3.115,0.698 3.26,0.875 0.146,0.177 10 false A 3.104,1.625 3.25,1.802 0.146,0.177 10 false A 3.135,2.896 3.24,3.042 0.104,0.146 10 false 9 1.823,4.354 1.938,4.5 0.115,0.146 10 false 3 1.365,2.375 1.458,2.531 0.094,0.156 10 false 4 1.01,4.354 1.125,4.5 0.115,0.146 10 false 5 2.188,2.49 2.302,2.646 0.115,0.156 10 false 6 2.375,4.323 2.5,4.479 0.125,0.156 10 false 7 0.823,2.375 0.917,2.521 0.094,0.146 10 false 8 0.604,4.365 0.781,4.51 0.177,0.146 10 false 10 3.115,3.823 3.292,3.969 0.177,0.146 10 false 11

Install the stiffening crankcase assembly with the 11 bolts in the sequence shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Bolt Length:
Item Specified Condition
Bolt A 138 mm (5.43 in.)
Bolt B 35 mm (1.38 in.)
Bolt C 70 mm (2.76 in.)


NOTICE:

Do not start the engine for at least 2 hours after installing the stiffening crankcase assembly.



c.

Recheck the torque for bolts 1 and 2.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Wipe off any excess seal packing with a clean piece of cloth.


Hide 15100 4.INSTALL OIL PUMP ASSEMBLY

Hide 12102A 5.INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

Hide 12101A 6.INSTALL OIL PAN DRAIN PLUG

a.

Install a new gasket and the oil pan drain plug.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 11432A 8.INSTALL NO. 1 TAPER SCREW PLUG

a.

Clean the No. 1 taper screw plug and plug hole.


b.

Apply adhesive to 2 or 3 threads of the No. 1 taper screw plug. Then install the No. 1 taper screw plug.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Install the plug within 3 minutes of applying adhesive.

·

Do not start the engine within 1 hour of installing the plug.




Hide 12204 9.INSTALL PCV VALVE SUB-ASSEMBLY

Hide 11101 11.INSTALL CYLINDER HEAD SUB-ASSEMBLY

Hide 13716 12.INSTALL VALVE STEM CAP

a.

Apply a light coat of engine oil to the valve stem cap end.


b.

Install the 16 valve stem caps to the valve stems.

NOTICE:

Do not drop the valve stem caps into the cylinder head sub-assembly.



Hide 13750 13.INSTALL VALVE LASH ADJUSTER ASSEMBLY

a.

Inspect each valve lash adjuster assembly before installing it.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION


b.

Install the 16 valve lash adjuster assemblies to the cylinder head sub-assembly.

NOTICE:

Install the valve lash adjuster assembly to the same place it was removed from.



Hide 13801 14.INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A250855C01
1.51,0.49 1.271,0.271 1.271,0.271 1.177,0.271 false 0.979,1.333 0.781,1.177 0.781,1.177 0.677,1.177 false 2.042,0.823 2.354,0.635 2.354,0.635 2.427,0.635 false 2,0.948 2.385,1.198 2.385,1.198 2.469,1.198 true 0.99,0.198 1.146,0.344 0.156,0.146 10 *1 0.49,1.083 0.656,1.229 0.167,0.146 10 *2 2.438,0.542 2.615,0.688 0.177,0.146 10 *4 2.479,1.104 2.656,1.25 0.177,0.146 10 *3
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Lash Adjuster Assembly
*3 Valve Stem
*4 Valve Stem Cap


Apply engine oil to the valve lash adjuster assembly tip and valve stem cap end.


b.

Make sure that the No. 1 valve rocker arm sub-assemblies are installed as shown in the illustration.


Hide 11114A 15.INSTALL CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove a straight pin unless it is being replaced.


A206181C02
1.177,2.417 1.521,2.656 0.344,0.24 10 *1 2.229,2.958 2.448,3.177 0.219,0.219 10 *3 2.708,2.427 2.906,2.604 0.198,0.177 10 *2
*1 Protrusion Height
*2 Height
*3 Width


a.

Using a plastic-faced hammer, tap in a new straight pin to the specified protrusion height.

Standard Straight Pin:
Protrusion Height Height Width
6.5 to 7.5 mm (0.256 to 0.295 in.) 14 mm (0.551 in.) 6.0 mm (0.236 in.)



Hide 222A0 16.INSTALL CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY

a.
A209173C02
0.917,2.917 1.167,2.917 1.167,2.917 1.458,1.958 true 0.74,2.833 0.979,3.042 0.24,0.208 10 *1
*1 Protrusion


Install a new O-ring to the continuously variable valve lift controller assembly.

NOTICE:
·

Align the protrusion of the O-ring with the protrusion of the continuously variable valve lift controller assembly.

·

Make sure that the O-ring is not protruding from the groove in the continuously variable valve lift controller assembly.




b.
A173632

Install the control actuator clip to the control actuator connector.

NOTICE:

Be sure to insert the protrusions of the control actuator clip into the holes in the control actuator connector.


HINT:

When the continuously variable valve lift controller assembly is new, a control actuator connector is attached to it. Remove the control actuator connector before performing these procedures.



c.
A320543

Install the control actuator connector to the valve rocker shaft.


d.

Insert the continuously variable valve lift controller assembly into the camshaft housing sub-assembly.


e.

Install the continuously variable valve lift controller to the camshaft housing sub-assembly with the bolt.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Do not let the O-ring become jammed between parts.



f.
A173790

Using a screwdriver, slide the control actuator clip from the control actuator connector.


g.

Slide only the upper part of the control actuator clip as the straight pin may fall if the control actuator clip is completely removed.


h.
A316504

Using 2 screwdrivers, lightly pry the control actuator connector and align the hole in the control actuator connector with the hole in the continuously variable valve lift controller assembly.

NOTICE:
·

Do not forcefully pry the control actuator connector.

·

Do not damage the camshaft housing sub-assembly and camshaft bearing cap.




i.
A320531C02
1.125,4.052 1.26,4.052 1.26,4.052 1.365,3.802 false 1.542,3.031 1.333,2.76 1.333,2.76 1.156,2.76 false 2.156,4.24 1.969,4.24 1.969,4.24 1.771,3.938 false 0.583,3.469 1.167,3.469 false 1.781,3.167 1.781,2.74 1.781,2.74 1.969,2.74 false 2.25,3.469 2.833,3.469 false 2.875,3.396 3.156,3.625 0.281,0.229 10 false *1 0.969,3.979 1.25,4.208 0.281,0.229 10 false *2 1,2.698 1.281,2.927 0.281,0.229 10 false *3 2.177,4.177 2.458,4.406 0.281,0.229 10 false *3 0.427,3.396 0.708,3.625 0.281,0.229 10 false *4 2.01,2.667 2.292,2.896 0.281,0.229 10 false *5
*1 Continuously Variable Valve Lift Controller Assembly
*2 Valve Lift Control Actuator Connector
*3 Valve Lift Control Actuator Connector Clip
*4 Valve Rocker Shaft
*5 Straight Pin


Insert the straight pin into the control actuator connector.

NOTICE:

Do not use a tool to insert the straight pin. Insert the straight pin by hand.


HINT:

If the straight pin is difficult to insert, insert the straight pin while lightly prying the control actuator connector.



j.
A320545

Using a screwdriver, install the control actuator clip to the control actuator connector.

NOTICE:

Insert the protrusion of the control actuator clip into the hole in the control actuator connector.



Hide 11103 17.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 13050 18.INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 19.INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13521A 20.INSTALL CRANKSHAFT TIMING GEAR KEY

a.
A150910

Using a plastic-faced hammer, tap in the 2 crankshaft timing gear keys.

HINT:

Tap in the crankshaft timing gear keys until they contact the crankshaft as shown in the illustration.



Hide 19315 21.INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.

Install the No. 1 crankshaft position sensor plate with the "F" mark facing forward.


Hide 13507 22.INSTALL NO. 2 CHAIN SUB-ASSEMBLY

Hide 13521 23.INSTALL CRANKSHAFT TIMING SPROCKET

Hide 13561 24.INSTALL NO. 1 CHAIN VIBRATION DAMPER

a.

Install the No. 1 chain vibration damper with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 25.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley bolt.


b.
A297251C01
1.719,1.094 1.719,0.344 1.719,0.344 1.885,0.344 true 1.979,0.271 2.292,0.427 0.313,0.156 10 *1
*1 Timing Gear Key


Turn the crankshaft counterclockwise to position the timing gear key at the top.


c.
A153030C04
0.458,0.865 0.927,1.375 0.927,1.375 1.521,0.885 true 0.844,1.406 1.021,1.604 0.177,0.198 10 *1
*1 Timing Mark


Check that the timing marks on the camshaft timing gears are aligned as shown in the illustration.


d.

Remove the crankshaft pulley bolt.


Hide 13506 26.INSTALL CHAIN SUB-ASSEMBLY

a.
A297252C01
0.688,0.417 0.167,1.25 0.167,1.25 0.167,1.417 true 0.698,0.344 1.5,0.083 1.5,0.083 1.75,0.083 true 0.802,3.823 1.271,3.323 1.271,3.323 1.521,3.323 true 0.823,3.979 1.333,4.417 1.333,4.417 1.5,4.417 true 1.792,0.01 2.104,0.167 0.313,0.156 10 *1 0.094,1.458 0.406,1.615 0.313,0.156 10 *2 1.552,3.25 1.865,3.406 0.313,0.156 10 *1 1.552,4.333 1.865,4.49 0.313,0.156 10 *2
*1 Mark Plate (Orange)
*2 Timing Mark


Align the mark plate (orange) with the timing mark as shown in the illustration and install the chain sub-assembly.

HINT:
·

Be sure to position the mark plate at the front of the engine.

·

The mark plate on the camshaft side is colored orange.

·

Do not pass the chain around the sprocket of the camshaft timing gear. Only place it on the sprocket.

·

Pass the chain through the No. 1 vibration damper.




b.
A172410

Place the chain on the crankshaft without passing it around the shaft.


c.

Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear counterclockwise to align the mark plate (orange) and timing mark, and then install the chain sub-assembly.


d.

Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear clockwise.

HINT:

To tension the chain, slowly turn the camshaft timing gear clockwise to prevent the chain from being misaligned.



e.
A172418C03
1.948,1.76 1.229,0.365 1.229,0.365 1.104,0.365 true 1.823,1.833 1.229,0.365 true 1.917,2.021 2.531,3.125 2.531,3.125 2.677,3.125 true 2.146,1.844 2.531,3.125 true 2.688,3.031 2.875,3.208 0.188,0.177 10 *2 0.896,0.271 1.052,0.417 0.156,0.146 10 *1
*1 Timing Mark
*2 Mark Plate (Pink)


Align the mark plates (pink) and timing marks and install the chain to the crankshaft timing gear.

HINT:

The mark plates on the crankshaft side are colored pink.



Hide 13559 27.INSTALL CHAIN TENSIONER SLIPPER

a.

Install the chain tensioner slipper to the cylinder block assembly.


Hide 28.CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Check each timing mark at TDC/compression.

A165311C01
0.771,1.375 0.969,0.938 0.969,0.938 1.135,0.938 true 2.396,1.469 2.396,1.052 2.396,1.052 2.229,1.052 true 0.781,1.469 0.781,2.219 true 2.365,1.594 2.365,2.26 true 5.5,0.833 5.667,0.833 5.667,0.833 5.792,1.635 true 6.25,0.833 6.083,0.833 6.083,0.833 5.854,1.594 true 6.073,2.229 5.906,2.229 5.906,2.229 5.906,1.646 true 5.646,2.302 5.813,2.302 5.813,2.302 5.813,1.719 true 0.719,2.25 1.031,2.406 0.313,0.156 10 *1 1.177,0.854 1.49,1.01 0.313,0.156 10 *2 2.073,0.969 2.385,1.125 0.313,0.156 10 *2 2.292,2.292 2.604,2.448 0.313,0.156 10 *1 6.292,0.75 6.604,0.906 0.313,0.156 10 *1 5.323,0.75 5.635,0.906 0.313,0.156 10 *1 6.115,2.146 6.427,2.302 0.313,0.156 10 *3 5.5,2.219 5.813,2.375 0.313,0.156 10 *3
*1 Timing Mark *2 Mark Plate (Orange)
*3 Mark Plate (Pink) - -



Hide 12511 29.INSTALL NO. 1 GENERATOR BRACKET

a.

Install the No. 1 generator bracket with the 4 bolts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


Hide 16323 30.INSTALL WATER INLET HOUSING

a.
A150906

Install a new gasket and the water inlet housing with the 3 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 11302 31.INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11302A 32.INSTALL TIMING CHAIN COVER OIL SEAL

Hide 33.INSTALL ENGINE MOUNTING BRACKET STUD BOLT

a.

Install the engine mounting bracket stud bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13540 35.INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A249855C02
0.165,0.122 0.335,0.279 0.17,0.157 10 *a 1.789,0.122 1.959,0.279 0.17,0.157 10 *b 0.54,0.108 0.705,0.26 0.165,0.152 10 *1 1.273,2.667 1.443,2.824 0.17,0.157 10 *3 0.893,0.318 0.806,0.186 0.806,0.186 0.725,0.186 false 2.117,0.108 2.282,0.26 0.165,0.152 10 *1 2.47,0.318 2.383,0.186 2.383,0.186 2.302,0.186 false 1.073,2.535 1.189,2.767 1.189,2.767 1.257,2.767 false 0.466,4.193 0.636,4.351 0.17,0.157 10 *3 1.006,3.998 0.765,4.269 0.765,4.269 0.66,4.269 false 0.653,3.129 0.818,3.281 0.165,0.152 10 *1 1.214,3.542 0.919,3.207 0.919,3.207 0.839,3.207 false 1.924,4.261 2.094,4.418 0.17,0.157 10 *2 1.246,4.022 1.772,4.358 1.772,4.358 1.911,4.358 false 0.5,2.221 0.67,2.379 0.17,0.157 10 *c 0.705,1.917 0.875,2.074 0.17,0.157 10 *d
*1 Cam
*2 Hook
*3 Pin
*a CORRECT
*b INCORRECT
*c Push
*d Raise


Release the cam, and then fully push in the plunger and engage the hook to the pin so that the plunger is in the position shown in the illustration.

NOTICE:

Make sure that the cam engages the first tooth of the plunger to allow the hook to pass over the pin.



b.
A150932

Install a new gasket, the No. 1 chain tensioner assembly and the bracket with the 2 nuts.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)

NOTICE:

If the hook releases the plunger while the No. 1 chain tensioner assembly is being installed, set the hook again.



c.
A250762C02
0.624,1.707 0.797,1.854 0.173,0.147 10 *a 0.865,2.361 1.038,2.508 0.173,0.147 10 *1 0.128,1.874 0.301,2.021 0.173,0.147 10 *2 1.507,2.798 1.68,2.945 0.173,0.147 10 *b 0.707,2.123 0.782,2.449 0.782,2.449 0.848,2.449 false 0.611,2.116 0.407,1.955 0.407,1.955 0.334,1.955 false
*1 Pin
*2 Hook
*a Release
*b Turn


Rotate the crankshaft counterclockwise slightly and check that the hook becomes released.


d.
A250763C02
0.888,1.918 1.041,2.071 0.153,0.153 10 *1 0.719,2.289 0.801,2.01 0.801,2.01 0.875,2.01 false 0.384,2.585 0.55,2.739 0.166,0.153 10 *a 1.477,2.743 1.643,2.896 0.166,0.153 10 *b
*1 Plunger
*a Plunger Extended
*b Turn


Turn the crankshaft clockwise and check that the plunger is extended.


Hide 15620 36.INSTALL OIL FILTER CAP ASSEMBLY

Hide 11193 37.INSTALL SPARK PLUG TUBE GASKET

a.
A153838C04
0.506,1.866 0.783,2.032 0.277,0.166 10 : *1
*1 Part to Cut Off


Using a cutter knife, cut off the seal part of the removed spark plug tube gasket.


b.
A179168C03
1.51,1.083 1.688,1.458 1.688,1.458 1.823,1.458 false 1.375,4.094 1.479,4.094 1.479,4.094 2.115,3.708 true 1.458,0.646 1.656,0.313 1.656,0.313 1.823,0.313 false 1.844,0.229 2.052,0.417 0.208,0.188 10 *1 1.854,1.385 2.052,1.563 0.198,0.177 10 *2 1.167,4 1.531,4.188 0.365,0.188 10 *3
*1 Spark Plug Tube Gasket without Sealing Part
*2 New Spark Plug Tube Gasket
*3 Claw


Using the removed spark plug tube gasket, uniformly press in a new spark plug tube gasket all the way.

NOTICE:
·

Keep the lip free of foreign matter.

·

Do not press in the spark plug tube gasket at an angle.



HINT:

If the removed spark plug tube gasket does not fit on the new one, correct the removed one with pliers.



c.

Return the claws of the ventilation baffle plate to their original positions.


Hide 11213 38.INSTALL CYLINDER HEAD COVER GASKET

a.

Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

NOTICE:

Remove any oil from the contact surfaces.



Hide 11201 39.INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

a.

Install 3 new gaskets to the camshaft bearing cap.


b.
A165302

Apply seal packing as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard diameter:

4.0 mm (0.157 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the cylinder head cover sub-assembly within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.




c.

Install the cylinder head cover sub-assembly with a new seal washer and the 13 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

NOTICE:

Do not start the engine for at least 2 hours after the installation.



Hide 83530 40.INSTALL ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89422 41.INSTALL ENGINE COOLANT TEMPERATURE SENSOR

Hide 11401G 43.INSTALL CRANKSHAFT POSITION SENSOR

Hide 11101J 44.INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 12635 47.INSTALL ENGINE COVER JOINT

a.

Install the 2 engine cover joints.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12108A 48.INSTALL OIL FILLER CAP GASKET

a.

Install the oil filler cap gasket to the oil filler cap sub-assembly.


Hide 12108 49.INSTALL OIL FILLER CAP SUB-ASSEMBLY

a.

Install the oil filler cap sub-assembly.