Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › CAMSHAFT
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046811 CAMSHAFT A

3ZR-FAE ENGINE MECHANICAL  CAMSHAFT  REMOVAL  


PROCEDURE

Hide 13506 1.REMOVE CHAIN SUB-ASSEMBLY

Hide 13050 2.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

a.

Inspect the lock of the camshaft timing gear assembly.


b.
A206198C01
0.667,0.688 0.5,1 0.5,1 0.5,1.333 true 1.604,1.313 0.833,2 0.833,2 0.667,2 true 0.823,0.385 1.083,0.125 1.083,0.125 1.198,0.125 true 1.229,0.052 1.542,0.208 0.313,0.156 10 *b 0.521,1.917 0.833,2.073 0.313,0.156 10 *1 0.438,1.344 0.75,1.5 0.313,0.156 10 *a
*1 Adhesive Tape
*a Prick a Hole
*b Adhesive Tape Sealing Area


After cleaning and degreasing the VVT oil hole on the intake side of the No. 1 camshaft bearing cap, completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

NOTICE:

Be sure to cover the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.



c.

Prick a hole in the tape covering the oil hole as shown in the illustration. (Procedure A)


d.
A173467

Apply compressed air at approximately 150 kPa (1.5 kgf/cm2, 22 psi) to the hole pricked in procedure A to release the lock pin.

NOTICE:
·

If air leaks out, reattach the adhesive tape.

·

Cover the oil hole with a piece of cloth when applying compressed air to prevent oil from spraying.




e.

Forcibly turn the camshaft timing gear in the advance direction (counterclockwise).

HINT:

Depending on the air pressure applied, the camshaft timing gear may turn in the advance direction without assistance.



f.
A173479

Turn the camshaft timing gear assembly within its movable range (26.5 to 28.5°) 2 or 3 times without turning it to the most retarded position. Make sure that the camshaft timing gear assembly turns smoothly.


g.

Remove the adhesive tape from the No. 1 camshaft bearing cap.


Hide 13070A 3.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.

Check the lock of the camshaft timing exhaust gear assembly.


b.
A206199C01
0.708,0.635 0.708,1.219 true 1.594,1 1.896,0.208 1.896,0.208 2.01,0.208 true 0.813,0.427 1.063,0.094 1.063,0.094 1.177,0.094 true 0.615,1.281 0.885,1.448 0.271,0.167 10 *a 2.063,0.115 2.333,0.292 0.271,0.177 10 *1 1.25,0.031 1.427,0.198 0.177,0.167 10 *b
*1 Adhesive Tape
*a Prick a Hole
*b Adhesive Tape Sealing Area


After cleaning and degreasing the VVT oil hole on the exhaust side of the No. 1 camshaft bearing cap, completely seal the oil hole with adhesive tape or equivalent as shown in the illustration to prevent air from leaking.

NOTICE:

Be sure to cover the oil hole completely because air leaks due to insufficient sealing will prevent the lock pin from being released.



c.

Prick a hole in the tape covering the oil hole as shown in the illustration. (Procedure A)


d.
A173468

Apply compressed air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the hole pricked in procedure A to release the lock pin.

NOTICE:
·

If air leaks out, reattach the adhesive tape.

·

Cover the oil hole with a piece of cloth when applying compressed air to prevent oil from spraying.




e.

Using a screwdriver with its tip wrapped with tape, forcibly turn the camshaft timing exhaust gear assembly in the retard direction (clockwise).

NOTICE:
·

Be sure to keep the camshaft timing exhaust gear assembly in the retard direction using a screwdriver. If the gear is released, it will return to the most advanced position automatically due to the force from the spring.

·

Do not damage the camshaft timing exhaust gear assembly.




f.
A173480

Using a screwdriver with its tip wrapped with tape, turn the camshaft timing exhaust gear assembly within its movable range (19 to 21°) 2 or 3 times without turning it to the most advanced position. Make sure that the camshaft timing exhaust gear assembly turns smoothly.


g.

Remove the adhesive tape from the No. 1 camshaft bearing cap.


Hide 13050 4.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

a.
A165296

Remove the flange bolt while holding the hexagonal portion of the camshaft, and then remove the camshaft timing gear assembly.

NOTICE:
A162976C07
1.083,1.604 1.542,1.917 1.542,1.917 1.729,1.917 true 0.479,1.458 0.479,1.74 false 1.24,1.427 1.542,1.906 true 0.344,0.719 0.542,0.719 0.542,0.719 0.969,0.927 true 0.531,0.719 0.833,1.146 true 0.396,1.771 0.708,1.927 0.313,0.156 10 *1 0.146,0.656 0.458,0.813 0.313,0.156 10 *a 1.802,1.823 2.115,1.979 0.313,0.156 10 *a
*1 Flange Bolt
*a Do Not Remove


·

Before removing the camshaft timing gear assembly, make sure that the lock pin has been released.

·

Be sure not to remove the other 4 bolts.

·

Keep the camshaft timing gear assembly horizontal while removing it from the camshaft.




Hide 13070A 5.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

a.
A165297

Remove the flange bolt while holding the hexagonal portion of the camshaft, and then remove the camshaft timing exhaust gear assembly.

NOTICE:
A162977C03
0.458,1.458 0.458,1.792 false 1.188,1.542 1.292,1.906 true 0.958,1.448 1.292,1.906 1.292,1.906 1.469,1.906 true 0.76,0.417 0.969,0.417 0.969,0.417 1.188,1.073 true 0.958,0.417 0.927,0.948 true 0.396,1.813 0.708,1.969 0.313,0.156 10 *1 0.552,0.313 0.865,0.469 0.313,0.156 10 *a 1.51,1.823 1.823,1.979 0.313,0.156 10 *a
*1 Flange Bolt
*a Do Not Remove


·

Be sure not to remove the other 4 bolts.

·

Keep the camshaft timing exhaust gear assembly horizontal while removing it from the camshaft.




Hide 13908 6.REMOVE VALVE ROCKER ARM LOST MOTION DAMPER SUB-ASSEMBLY

a.
A199175C04
1.323,4.427 1.073,4.427 1.073,4.427 1.073,3.76 true 2.552,4.438 2.302,4.438 2.302,4.438 2.302,3.771 true 1.385,4.333 1.698,4.49 0.313,0.156 10 *1 2.625,4.344 2.938,4.5 0.313,0.156 10 *1
*1 Shim


Remove the 2 bolts and valve rocker arm lost motion damper sub-assembly.

NOTICE:
·

Make sure the camshaft housing sub-assembly is installed to the cylinder head sub-assembly when removing or installing a valve rocker arm lost motion damper sub-assembly.

·

If a valve rocker arm lost motion damper sub-assembly is removed, do not remove the camshaft housing sub-assembly.

·

Do not remove the shims. If a shim is removed, replace the camshaft housing sub-assembly as engine malfunctions may result from irregular valve timing.




Hide 13908 7.INSTALL VALVE ROCKER ARM LOST MOTION DAMPER SUB-ASSEMBLY

a.
A199176C04
1.729,1.448 1.729,1.948 true 1.667,2 1.844,2.146 0.177,0.146 10 *1
*1 Hole for Engine Oil


Install the valve rocker arm lost motion damper sub-assembly with the 2 bolts. Uniformly tighten the bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Add engine oil into the hole for engine oil.


Hide 11103 8.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

NOTICE:
·

The camshaft housing sub-assembly is replaced with an assembled unit that includes the camshaft housing sub-assembly, camshafts, camshaft bearing caps, valve rocker shaft and valve rocker arm lost motion damper sub-assembly. If disassembled, replace the camshaft housing sub-assembly.

·

The camshafts cannot be replaced by themselves.

A206559C01
0.365,0.354 0.677,0.51 0.313,0.156 10 *1 3.938,0.573 4.25,0.729 0.313,0.156 10 *2 0.521,3.406 0.833,3.563 0.313,0.156 10 *a
*1 Camshaft Housing Sub-assembly *2 Continuously Variable Valve Lift Controller Assembly
*a Set of parts that are replaced together - -




a.
A270926N01
0.604,0.104 0.76,0.302 0.156,0.198 10 1 0.396,0.083 0.552,0.281 0.156,0.198 10 4 1.365,0.156 1.625,0.344 0.26,0.188 10 16 0.917,0.167 1.177,0.354 0.26,0.188 10 10 1.854,0.146 2.115,0.333 0.26,0.188 10 13 2.365,0.135 2.625,0.323 0.26,0.188 10 7 2.844,0.927 3.104,1.115 0.26,0.188 10 2 1.552,0.698 1.813,0.885 0.26,0.188 10 14 1.083,0.708 1.344,0.896 0.26,0.188 10 17 0.594,0.708 0.854,0.896 0.26,0.188 10 11 0.385,1.927 0.646,2.115 0.26,0.188 10 3 0.938,1.833 1.198,2.021 0.26,0.188 10 9 1.396,1.854 1.656,2.042 0.26,0.188 10 15 1.844,1.854 2.104,2.042 0.26,0.188 10 12 2.354,1.865 2.615,2.052 0.26,0.188 10 6 0.115,0.875 0.375,1.063 0.26,0.188 10 5 2.073,0.708 2.333,0.896 0.26,0.188 10 8

Uniformly loosen and remove the 17 bearing cap bolts in the sequence shown in the illustration.

NOTICE:

Uniformly loosen the bearing cap bolts while keeping the camshaft housing sub-assembly level.



b.
A165298C04
0.948,1.385 1.104,1.385 1.104,1.385 1.479,1.104 false 0.323,3.344 0.469,3.344 0.469,3.344 0.521,4.125 false 1.635,3.74 1.781,3.74 1.781,3.74 2.073,4.208 false 0.792,1.313 1.104,1.469 0.313,0.156 10 *1 0.167,3.271 0.479,3.427 0.313,0.156 10 *1 1.469,3.667 1.781,3.823 0.313,0.156 10 *1
*1 Protective Tape


Remove the camshaft housing sub-assembly by prying between the cylinder head sub-assembly and camshaft housing sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and camshaft housing sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 13801 9.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 10.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 13801 11.INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 12.INSPECT VALVE LASH ADJUSTER ASSEMBLY