Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › ENGINE UNIT › 2012.12–2014.10
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046816 ENGINE UNIT A

3ZR-FAE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.
A173599

Remove the oil filler cap sub-assembly.


Hide 12108A 2.REMOVE OIL FILLER CAP GASKET

a.
A128159

Remove the oil filler cap gasket.


Hide 12635 3.REMOVE ENGINE COVER JOINT

a.
A150847

Remove the 2 engine cover joints.


Hide 11101W 5.REMOVE CAMSHAFT POSITION SENSOR

Hide 11101J 6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 11401G 7.REMOVE CRANKSHAFT POSITION SENSOR

Hide 83530 8.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89422 10.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 11201 11.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A173472

Remove the 13 bolts, seal washer and cylinder head cover sub-assembly.


b.
A165301

Remove the 3 gaskets from the camshaft bearing cap.

NOTICE:

As gaskets may stick to the cylinder head cover sub-assembly, be careful not to drop any of the gaskets into the engine when removing the cylinder head cover sub-assembly.



Hide 11213 12.REMOVE CYLINDER HEAD COVER GASKET

a.
A179166

Remove the cylinder head cover gasket.


Hide 11193 13.REMOVE SPARK PLUG TUBE GASKET

a.
A179167

Pry up the 4 claws of the ventilation baffle plate.

NOTICE:

Do not deform the claws of the ventilation baffle plate more than necessary.



b.
A329121

Using a screwdriver as shown in the illustration, deform each spark plug tube gasket inwards and remove the 4 spark plug tube gaskets from cylinder head cover sub-assembly.

NOTICE:
·

As much as possible prevent the spark plug tube gaskets from being deformed.

The removed spark plug tube gaskets will be used when reinstalling the new spark plug tube gaskets.

·

Do not damage the cylinder head cover sub-assembly.

·

Make sure not to damage the spark plug tube gasket and cylinder head cover sub-assembly when inserting the screwdriver in the joint area.



HINT:

If the cylinder head cover sub-assembly is damaged, smooth the surface with 400-grid sandpaper.



Hide 15620 14.REMOVE OIL FILTER CAP ASSEMBLY

Hide 15.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A297250C01
0.823,2.458 0.99,2.458 0.99,2.458 0.99,1.708 true 2.344,2.531 2.177,2.531 2.177,2.531 2.177,1.781 true 0.406,2.792 0.573,2.792 0.573,2.792 1.073,3.208 true 0.333,4.042 0.5,4.042 0.5,4.042 1,3.375 true 0.677,2.385 0.99,2.542 0.313,0.156 10 *1 0.167,3.958 0.479,4.115 0.313,0.156 10 *2 2.385,2.448 2.698,2.604 0.313,0.156 10 *1 0.26,2.719 0.573,2.875 0.313,0.156 10 *1
*1 Timing Mark
*2 Notch


Turn the crankshaft pulley until its notch and timing mark "0" of the timing chain cover are aligned.


b.

Check that the timing marks on both the camshaft timing exhaust gear and camshaft timing gear are facing upward as shown in the illustration.

HINT:

If the marks are not as shown, turn the crankshaft 1 complete revolution (360°) and align the marks as specified above.



Hide 13540 17.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A250765

Remove the 2 nuts, bracket, No. 1 chain tensioner assembly and gasket.

NOTICE:

Do not turn the crankshaft without the No. 1 chain tensioner installed.



Hide 18.REMOVE ENGINE MOUNTING BRACKET STUD BOLT

a.
A211980

Remove the engine mounting bracket stud bolt.


Hide 11302 19.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11302A 20.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 16323 21.REMOVE WATER INLET HOUSING

a.
A150906

Remove the 3 bolts, water inlet housing and gasket.


Hide 12511 22.REMOVE NO. 1 GENERATOR BRACKET

a.
A150905

Remove the 4 bolts and No. 1 generator bracket.


Hide 13559 23.REMOVE CHAIN TENSIONER SLIPPER

a.
A173477

Remove the chain tensioner slipper from the cylinder block assembly.


Hide 13561 24.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A165303

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13506 25.REMOVE CHAIN SUB-ASSEMBLY

a.
A165304

Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear counterclockwise to loosen the chain sub-assembly between the camshaft timing gears.


b.

With the chain sub-assembly loosened, release the chain sub-assembly from the camshaft timing gear and place it on the camshaft timing gear.

HINT:

Be sure to release the chain sub-assembly from the sprocket completely.



c.

Turn the camshaft clockwise to return it to the original position and remove the chain sub-assembly.


Hide 13521 26.REMOVE CRANKSHAFT TIMING SPROCKET

Hide 13507 27.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

Hide 19315 28.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A150874

Remove the No. 1 crankshaft position sensor plate.


Hide 13521A 29.REMOVE CRANKSHAFT TIMING GEAR KEY

a.
A150909C07
0.672,0.666 0.837,0.828 0.165,0.162 10 *1 0.857,0.763 0.964,0.763 0.964,0.763 1.178,1.335 false
*1 Protective Tape


Using a screwdriver, remove the 2 crankshaft timing gear keys.

HINT:

Tape the screwdriver tip before use.



Hide 13050 30.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 31.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13050 32.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 33.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13908 34.REMOVE VALVE ROCKER ARM LOST MOTION DAMPER SUB-ASSEMBLY

Hide 13908 35.INSTALL VALVE ROCKER ARM LOST MOTION DAMPER SUB-ASSEMBLY

Hide 11103 36.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 222A0 37.REMOVE CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY

a.
A173790

Using a screwdriver, slide the control actuator clip from the control actuator connector.

NOTICE:

Slide only the upper part of the control actuator clip, as the straight pin may fall if the control actuator clip is completely removed.



b.
A316504

Using 2 screwdrivers, lightly pry the control actuator connector to make a space between the continuously variable valve lift controller assembly and camshaft housing sub-assembly.

NOTICE:
·

Do not forcefully pry the control actuator connector.

·

Do not damage the camshaft housing sub-assembly and camshaft bearing cap.




c.
A174269

Using a magnet hand, remove the straight pin from the control actuator connector.

HINT:

The straight pin can be removed by utilizing the space between the continuously variable valve lift controller assembly and camshaft housing sub-assembly to move the continuously variable valve lift controller assembly so that there is no load on the straight pin.



d.
A317707C01
2.521,0.781 2.188,0.427 2.188,0.427 1.99,0.427 false 2.625,1.969 2.448,1.969 2.448,1.969 2.229,1.604 false 2.667,1.896 2.865,2.063 0.198,0.167 10 false *2 1.781,0.344 1.979,0.51 0.198,0.167 10 false *1
*1 Continuously Variable Valve Lift Controller Assembly
*2 O-Ring


Remove the bolt and the continuously variable valve lift controller assembly from the camshaft housing sub-assembly.


e.

Remove the O-ring from the continuously variable valve lift controller assembly.

NOTICE:

The O-ring may remain on the camshaft housing side. Be sure to always remove it.



f.
A320543

Remove the valve lift control actuator connector from the valve rocker shaft.


Hide 13801 38.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A174965

Remove the 16 valve rocker arm sub-assemblies.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 39.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.
A270930

Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 40.REMOVE VALVE STEM CAP

a.
A150945

Remove the 16 valve stem caps.

HINT:

Arrange the removed parts in the correct order.



Hide 11101 41.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11114A 42.REMOVE CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove a straight pin unless it is being replaced.


Hide 12204 44.REMOVE PCV VALVE SUB-ASSEMBLY

Hide 12101A 45.REMOVE OIL PAN DRAIN PLUG

a.
A150893

Remove the oil pan drain plug and gasket.


Hide 12102A 46.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15100 47.REMOVE OIL PUMP ASSEMBLY

Hide 11420 49.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A150897

Uniformly loosen and remove the 11 bolts.


b.
A150898C07
0.448,3.021 0.604,3.427 0.604,3.427 0.604,3.552 true 1.198,3.51 1.344,3.896 1.344,3.896 1.344,4.021 true 2.479,3.375 2.646,3.729 2.646,3.729 2.646,3.854 true 3.094,2.656 3.25,2.969 3.25,2.969 3.25,3.094 true 0.521,3.583 0.719,3.771 0.198,0.188 10 *1 1.25,4.052 1.448,4.24 0.198,0.188 10 *1 2.552,3.885 2.75,4.073 0.198,0.188 10 *1 3.156,3.125 3.354,3.313 0.198,0.188 10 *1
*1 Protective Tape


Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block assembly.

NOTICE:

Be careful not to damage the contact surfaces of the stiffening crankcase assembly and cylinder block assembly.


HINT:

Tape the screwdriver tip before use.



Hide 11432A 50.REMOVE NO. 1 TAPER SCREW PLUG

a.
A300838

Remove the No. 1 taper screw plug.


Hide 51.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 52.REMOVE STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove a stiffening crankcase ring pin unless it is being replaced.