Home › Engine / Hybrid System › 3ZR-FAE ENGINE MECHANICAL › CYLINDER HEAD GASKET
RM3090E _51 Engine / Hybrid System _008387 3ZR-FAE ENGINE MECHANICAL _0046812 CYLINDER HEAD GASKET A

3ZR-FAE ENGINE MECHANICAL  CYLINDER HEAD GASKET  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 11115 1.INSTALL CYLINDER HEAD GASKET

a.
A235098C01
1.396,0.323 1.229,0.323 1.229,0.323 0.917,0.469 false 1.365,0.771 1.208,0.771 1.208,0.771 1.135,0.594 false 1.406,0.688 1.719,0.844 0.313,0.156 10 *1 1.438,0.25 1.75,0.406 0.313,0.156 10 *2 1.052,0.052 1.365,0.208 0.313,0.156 10 *a 1.302,1.198 1.615,1.354 0.313,0.156 10 *b 1.271,2.531 1.583,2.688 0.313,0.156 10 *b
*1 Cylinder Block Assembly
*2 Seal Packing
*a Distance from Edge of Cylinder Block Assembly to Center of Seal Packing
*b Seal Packing Application Length
V100135

Engine Front


Apply seal packing to the cylinder block assembly as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal packing diameter:

4.0 mm (0.157 in.)


Application Specification:
Distance from Edge of Cylinder Block to Center of Seal Packing Seal Packing Application Length
0 to 2.0 mm (0 to 0.0787 in.) 10 to 15 mm (0.394 to 0.591 in.)


NOTICE:

Remove any oil from the cylinder block assembly.



b.
A221760C09
1.427,0.521 1.646,0.083 1.646,0.083 1.958,0.083 true 1.99,0 2.302,0.156 0.313,0.156 10 *1
*1 Lot No.
V100135

Engine Front


Place a new cylinder head gasket on the cylinder block assembly with the lot No. stamp facing upward.

NOTICE:

Install the cylinder head gasket within 3 minutes after applying seal packing.



c.
A235099C01
1.573,0.49 1.438,0.49 1.438,0.49 1.323,0.615 false 1.573,0.094 1.448,0.094 1.448,0.094 1.125,0.479 false 0.573,0.031 0.865,0.24 0.292,0.208 10 *a 1.396,0.979 1.646,1.135 0.25,0.156 10 *b 1.344,2.5 1.573,2.667 0.229,0.167 10 *b 1.604,0.406 1.813,0.573 0.208,0.167 10 *1 1.604,0 2.479,0.177 0.875,0.177 10 *2
*1 Cylinder Head Gasket
*2 Seal Packing
*a Distance from Edge of Cylinder Head Gasket to Center of Seal Packing
*b Seal Packing Application Length
V100135

Engine Front


Apply seal packing to the cylinder head gasket as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Standard seal packing diameter:

4.0 mm (0.157 in.)


Application Specification:
Distance from Edge of Cylinder Head Gasket to Center of Seal Packing Seal Packing Application Length
2.0 to 4.0 mm (0.0787 to 0.157 in.) 10 to 15 mm (0.394 to 0.591 in.)


NOTICE:
·

Remove any oil from the cylinder head gasket and cylinder head sub-assembly.

·

Install the cylinder head sub-assembly within 3 minutes and tighten the bolts within 15 minutes of applying seal packing.




Hide 11101 2.INSTALL CYLINDER HEAD SUB-ASSEMBLY

HINT:
·

The cylinder head bolts are tightened in 3 progressive steps.

·

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly.

Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



a.

Place the cylinder head sub-assembly on the cylinder block assembly.

NOTICE:
·

Make sure that no oil is on the mounting surface of the cylinder head sub-assembly.

·

Place the cylinder head sub-assembly on the cylinder block assembly gently in order not to damage the gasket with the bottom part of the cylinder head sub-assembly.




b.

Install the plate washers to the cylinder head bolts.


c.

Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.


d.
A150891E02
0.583,0.099 0.691,0.25 0.108,0.152 10 8 1.122,0.099 1.229,0.25 0.108,0.152 10 4 1.668,0.113 1.775,0.264 0.108,0.152 10 2 2.2,0.113 2.308,0.264 0.108,0.152 10 5 2.768,0.092 2.875,0.244 0.108,0.152 10 9 1.647,1.78 1.761,1.935 0.114,0.155 10 1 1.095,1.782 1.202,1.933 0.108,0.152 10 6 0.506,1.782 0.697,1.933 0.191,0.152 10 10 2.225,1.782 2.333,1.933 0.108,0.152 10 3 2.775,1.782 2.883,1.933 0.108,0.152 10 7

Step 1:

i.

Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 10 cylinder head bolts in several steps, in the sequence shown in the illustration.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:

Do not drop the plate washers into the cylinder head sub-assembly.




e.

Step 2:

i.

Mark the front side of each cylinder head bolt head with paint.


ii.

Tighten the cylinder head bolts 90°.



f.

Step 3:

i.

Tighten the cylinder head bolts an additional 45°.


ii.

Check that the paint marks are now at a 135° angle to the front.



g.
A214976C08
0.893,2.009 1.056,2.193 0.163,0.184 10 *a 2.508,2.009 2.691,2.177 0.183,0.168 10 *b
*a Before wiping off
*b After wiping off


After tightening the cylinder head bolts, wipe off the seal packing material that has seeped out from between the contact surfaces of the cylinder head sub-assembly and cylinder block assembly.


Hide 16268 4.CONNECT NO. 1 WATER BY-PASS PIPE

a.

Connect the No. 1 water by-pass pipe to the cylinder head sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 11103 6.INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY