Home › Engine / Hybrid System › 2AR-FE ENGINE MECHANICAL › ENGINE
RM3090E _51 Engine / Hybrid System _008396 2AR-FE ENGINE MECHANICAL _0046871 ENGINE G

2AR-FE ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

HINT:

The type of ignition switch used on this model differs according to the specifications of the vehicle. For the expressions listed in this section, refer to the "Ignition Switch Expressions" precaution.

Click hereEngine / Hybrid System>2AR-FE STARTING>STARTING SYSTEM>PRECAUTION


PROCEDURE

Hide 17801 4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner cap.


b.

Remove the air cleaner filter element sub-assembly.


c.

Visually check that the air cleaner filter is not excessively damaged or oily.

If necessary, replace the air cleaner filter element sub-assembly.


Hide 16361A 6.INSPECT FAN AND GENERATOR V BELT

Hide 13750 7.INSPECT VALVE LASH ADJUSTER ASSEMBLY NOISE

a.

Rev up the engine several times. Check that the engine does not emit unusual noises.

If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then perform the inspection above again.

If any defects or problems are found during the inspection above, perform a lash adjuster inspection.

Click hereEngine / Hybrid System>2AR-FE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION


Hide 8.INSPECT IGNITION TIMING

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and idle it.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.

Powertrain > Engine and ECT > Data List
Tester Display
IGN Advance
50003 234 29
Standard ignition timing:

5 to 15° BTDC @ idle


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

Check the ignition timing with the cooling fan off.

·

When checking the ignition timing, the shift lever should be in N or P.



HINT:

Refer to the GTS operator's manual for further details.

If the ignition timing is not as specified, check the valve timing.



v.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.

Powertrain > Engine and ECT > Active Test
Tester Display
Connect the TC and TE1
50004 234 13

vi.

Monitor IGN Advance of the Data List.

Standard ignition timing:

8 to 12 BTDC @ idle


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

Check the ignition timing with the cooling fan off.

·

When checking the ignition timing, the shift lever should be in N or P.




vii.

Check that the ignition timing advances immediately when the engine speed is increased.


viii.

Turn the ignition switch off.


ix.

Disconnect the GTS from the DLC3.



c.

When not using the GTS:

i.

Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

NOTICE:

Use a timing light that detects primary signals.



ii.

Start the engine and idle it.


iii.
A206183C25
1.208,0.313 1.344,0.313 1.344,0.313 1.573,0.906 true 2.135,1.865 2,1.865 2,1.865 1.792,1.479 true 0.083,0.063 0.281,0.26 0.198,0.198 10 false *a 0.917,0.229 1.198,0.427 0.281,0.198 10 false CG 2.198,1.771 2.458,1.948 0.26,0.177 10 false TC
*a Front view of DLC3


Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

SST
09843-18040  

NOTICE:
·

Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.

·

When checking the ignition timing, the shift lever should be in N or P.




iv.

Using a timing light, check the ignition timing.

Standard ignition timing:

8 to 12° BTDC @ idle


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

Check the ignition timing with the cooling fan off.

·

When checking the ignition timing, the shift lever should be in N or P.




v.

Remove SST from the DLC3.


vi.

Check the ignition timing.

Standard ignition timing:

5 to 15° BTDC @ idle


NOTICE:
·

Turn all the electrical systems and the A/C off.

·

Check the ignition timing with the cooling fan off.

·

When checking the ignition timing, the shift lever should be in N or P.



If the ignition timing is not as specified, check the valve timing.


vii.

Check that the ignition timing advances immediately when the engine speed is increased.


viii.

Turn the ignition switch off.


ix.

Disconnect the timing light from the engine.



Hide 9.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.

HINT:

Switch off all accessories and the A/C before connecting the GTS.



ii.

Race the engine at 2500 rpm for approximately 90 seconds.


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9
Standard idle speed:

720 to 820 rpm


NOTICE:

When checking the idle speed, the shift lever should be in N or P.


HINT:

Refer to the GTS operator's manual for further details.


If the idle speed is not as specified, check the air intake system.


v.

Disconnect the GTS from the DLC3.



c.

When not using the GTS:

i.
A206183C26
0.056,0.0 0.245,0.207 0.189,0.207 10 *a 0.399,1.727 0.722,1.907 0.323,0.181 10 TAC 0.784,1.808 0.9,1.808 0.9,1.808 1.046,1.437 false
*a Front view of DLC3


Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

SST
09843-18030  

NOTICE:

Confirm the terminal number before connecting the probe. Connecting the wrong terminals can damage the engine.


HINT:

Switch off all accessories and the A/C.



ii.

Race the engine at 2500 rpm for approximately 90 seconds.


iii.

Check the idle speed.

Standard idle speed:

720 to 820 rpm


NOTICE:

When checking the idle speed, the shift lever should be in N or P.


If the speed is not as specified, check the air intake system.


iv.

Disconnect the tachometer probe from the DLC3.



Hide 10.INSPECT COMPRESSION

a.

Warm up and stop the engine.




d.

Disconnect the 4 fuel injector connectors.


e.

Insert a compression gauge into the spark plug hole.


f.

Fully open the throttle.


g.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

1450 kPa (14.8 kgf/cm2, 210 psi) or higher


Minimum pressure:

980 kPa (10.0 kgf/cm2, 142 psi)


Difference between each cylinder:

200 kPa (2.0 kgf/cm2, 29 psi) or less


HINT:

Always use a fully charged battery to obtain an engine speed of 250 rpm or more.



h.

If the cylinder compression is low in one or more cylinders, pour a small amount of engine oil into the cylinder with low compression through its spark plug hole. Then inspect the cylinder compression pressure again.

HINT:
·

If adding oil helps boost the compression, it is likely that the piston rings and/or cylinder bore is worn or damaged.

·

If the pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.




i.

Connect the 4 fuel injector connectors.




Hide 11.INSPECT CO/HC

HINT:

This check determines whether or not the idle CO/HC complies with regulations.


a.

Start the engine.


b.

Keep the engine speed at 2500 rpm for approximately 180 seconds.


c.

Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.


d.

Immediately check the CO/HC concentration at idle and at 2500 rpm.

HINT:
·

When performing the 2-mode (2500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.

·

If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.



i.

Check the air fuel ratio sensor operation.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>INSPECTION


ii.

Check the heated oxygen sensor operation.

Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION


iii.

See the table below for possible causes, and then inspect and correct the applicable causes if necessary.

CO HC Symptom Causes
Normal High Rough idle

1. Faulty ignition

·

Incorrect timing

·

Plugs are contaminated or shorted, or gaps are defective


2. Leaky intake and exhaust valves

3. Leaky cylinder


Low High Rough idle
(Fluctuating HC reading)

1. Vacuum leaks

·

PCV hose

·

Intake manifold

·

Throttle body

·

Brake booster line


2. Lean mixture causing misfire


High High Rough idle
(Black smoke from exhaust)

1. Restricted air filter

2. Faulty SFI system

·

Faulty pressure

·

Defective engine coolant temperature sensor

·

Faulty ECM

·

Faulty injector

·

Faulty throttle position sensor

·

Faulty mass air flow meter sensor