Home › Engine / Hybrid System › 2AR-FE FUEL › FUEL TANK(w/o Canister Pump Module)
RM3090E _51 Engine / Hybrid System _008397 2AR-FE FUEL _0046886 FUEL TANK(w/o Canister Pump Module) A

2AR-FE FUEL  FUEL TANK(w/o Canister Pump Module)  INSTALLATION  


PROCEDURE

Hide 1.INSTALL FUEL EMISSION HOSE

a.

Install the fuel emission hose.

NOTICE:
·

Before connecting the fuel emission hose, check if there is any damage or foreign matter in the fuel emission hose or connector.

·

Check that the connector is connected by pulling on it.



HINT:

Firmly push the tube connector until a "click" sound is heard.



Hide 77707 2.INSTALL CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

a.

Install the charcoal canister outlet tube sub-assembly to the fuel tank assembly and attach the 2 clamps.


Hide 77295D 3.INSTALL FUEL TUBE GROMMET

a.

Install the 3 fuel tube grommets to the fuel tank assembly.


Hide 77299A 4.INSTALL NO. 5 FUEL TUBE CLAMP

a.

Install the No. 5 fuel tube clamp to the fuel tank assembly.


Hide 77289B 5.INSTALL NO. 3 FUEL TUBE CLAMP

a.

Install the No. 3 fuel tube clamp to the fuel tank assembly.


Hide 77026A 6.INSTALL NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Install the No. 1 fuel evaporation tube sub-assembly and attach the 5 clamps.


Hide 77209D 7.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Install the fuel tank main tube sub-assembly and attach the 5 clamps.


Hide 83320 8.INSTALL FUEL SENDER GAUGE ASSEMBLY

Hide 9.INSTALL FUEL SUCTION TUBE ASSEMBLY WITH PUMP

Hide 77168A 10.INSTALL FUEL TANK VENT TUBE SET PLATE

Hide 77209D 11.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

Hide 77100 13.INSTALL FUEL TANK ASSEMBLY

a.

Set the fuel tank assembly on an engine lifter with attachments.


b.

Lift up the engine lifter.


c.

Attach the wire harness to the 3 clamps.


d.

Connect the fuel pump connector and sender gauge connector.

NOTICE:

Be careful not to cut the wiring.



e.

Install the No. 1 fuel tank band sub-assembly with the 2 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


f.

Install the No. 1 fuel tank band sub-assembly LH with the 2 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


g.

Install the No. 2 fuel tank band sub-assembly with the 2 bolts.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)


h.

Attach the 3 wire harness clamps.


Hide 77014A 14.CONNECT NO. 3 FUEL TANK BREATHER TUBE SUB-ASSEMBLY

a.

Connect the No. 3 fuel tank breather tube sub-assembly to the fuel tank assembly.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/o Canister Pump Module)>PRECAUTION


Hide 77707 15.CONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

a.

Connect the charcoal canister outlet tube sub-assembly to the fuel tank breather tube and slide the clamp to secure it.


b.

Attach the hose clamp.


Hide 77213E 16.CONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A300870C01
1.542,3.01 1.74,3.604 1.74,3.604 1.844,3.604 false 2.708,2.802 2.615,3.573 2.615,3.573 2.5,3.573 true 0.875,3.781 1.188,3.938 0.313,0.156 10 false *1 1.875,3.521 2.188,3.677 0.313,0.156 10 false *2 2.333,3.479 2.646,3.635 0.313,0.156 10 false *3 0.594,2.021 0.906,2.177 0.313,0.156 10 false *a 2.292,2.323 2.604,2.479 0.313,0.156 10 false *b 1.094,3.302 1.552,3.5 0.458,0.198 10 false 45° 0.385,3.469 0.844,3.667 0.458,0.198 10 false 90°
*1 Range
*2 Stopper
*3 Protrusion
*a Top of Vehicle
*b Bottom of Fuel Tank


Connect the fuel tank to filler pipe hose to the fuel tank assembly and tighten the hose clamp.

HINT:

Make sure the hose clamp is oriented as shown in the illustration.



Hide 77276 17.INSTALL FUEL HOSE PROTECTOR

a.

Install the fuel hose protector to the fuel tank to filler pipe hose and attach the claw.


Hide 77026A 18.CONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Connect the No. 1 fuel evaporation tube sub-assembly and slide the clamp to secure it.


Hide 77209D 19.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Connect the fuel tank main tube sub-assembly.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/o Canister Pump Module)>PRECAUTION


Hide 77641A 20.INSTALL NO. 1 FUEL TANK PROTECTOR

a.

Install the No. 1 fuel tank protector with the 2 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.

Install the 2 clips and grommet.


Hide 21.CONNECT PARKING BRAKE CABLE

a.

Connect the parking brake cable with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 22.ADD FUEL

Hide 23.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION