Home › Engine / Hybrid System › 2AR-FE FUEL › FUEL TANK(w/o Canister Pump Module)
RM3090E _51 Engine / Hybrid System _008397 2AR-FE FUEL _0046886 FUEL TANK(w/o Canister Pump Module) A

2AR-FE FUEL  FUEL TANK(w/o Canister Pump Module)  REMOVAL  


PROCEDURE

Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 4.DRAIN FUEL

Hide 5.DISCONNECT PARKING BRAKE CABLE

a.
A293546

Remove the 2 bolts and disconnect the parking brake cable.


Hide 77641A 6.REMOVE NO. 1 FUEL TANK PROTECTOR

a.
A293548

Remove the 2 clips and grommet.


b.

Remove the 2 bolts and No. 1 fuel tank protector.


Hide 77026A 7.DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.
A293550

Slide the clamp and disconnect the No. 1 fuel evaporation tube sub-assembly.


Hide 77209D 8.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.
A293551

Disconnect the fuel tank main tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/o Canister Pump Module)>PRECAUTION


Hide 77276 9.REMOVE FUEL HOSE PROTECTOR

A199132

a.

Detach the claw and remove the fuel hose protector from the fuel tank to filler pipe hose.


Hide 77213E 10.DISCONNECT FUEL TANK TO FILLER PIPE HOSE

a.
A173328

Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank assembly.


Hide 77707 11.DISCONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

a.
A293554

Detach the hose clamp.


b.
A293552

Slide the clamp and disconnect the charcoal canister outlet tube sub-assembly from the fuel tank breather tube.


Hide 77014A 12.DISCONNECT NO. 3 FUEL TANK BREATHER TUBE SUB-ASSEMBLY

a.
A293553

Disconnect the No. 3 fuel tank breather tube sub-assembly from the fuel tank assembly.

Click hereEngine / Hybrid System>2AR-FE FUEL>FUEL SYSTEM(w/o Canister Pump Module)>PRECAUTION


Hide 77100 13.REMOVE FUEL TANK ASSEMBLY

a.
A293577

Detach the 3 wire harness clamps.


b.

Using an engine lifter and attachments, support the fuel tank assembly.


c.
A293555

Remove the 2 bolts and No. 1 fuel tank band sub-assembly.


d.

Remove the 2 bolts and No. 1 fuel tank band sub-assembly LH.


e.

Remove the 2 bolts and No. 2 fuel tank band sub-assembly.


f.

Slightly lower the engine lifter.

NOTICE:

Be careful not to cut the wiring.



g.
A297843

Disconnect the fuel pump connector and sender gauge connector.

NOTICE:
·

Before this procedure, check the connector for dirt, mud or other contamination.

·

Do not use any tools in this procedure.




h.

Detach the wire harness from the 3 clamps and remove the fuel tank assembly.


Hide 77209D 15.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

Hide 77168A 16.REMOVE FUEL TANK VENT TUBE SET PLATE

Hide 17.REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP

Hide 83320 18.REMOVE FUEL SENDER GAUGE ASSEMBLY

Hide 77209D 19.REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

A299336

a.

Detach the 5 clamps and remove the fuel tank main tube sub-assembly.


Hide 77026A 20.REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY

a.

Detach the 5 clamps and remove the No. 1 fuel evaporation tube sub-assembly.


Hide 77289B 21.REMOVE NO. 3 FUEL TUBE CLAMP

a.

Remove the No. 3 fuel tube clamp from the fuel tank assembly.


Hide 77299A 22.REMOVE NO. 5 FUEL TUBE CLAMP

a.

Remove the No. 5 fuel tube clamp from the fuel tank assembly.


Hide 77295D 23.REMOVE FUEL TUBE GROMMET

a.

Remove the 3 fuel tube grommets from the fuel tank assembly.


Hide 77707 24.REMOVE CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY

a.
A293558

Detach the 2 clamps and remove the canister outlet tube sub-assembly from the fuel tank.


Hide 25.REMOVE FUEL EMISSION HOSE

a.
A293559C01
0.75,1.115 0.75,0.917 0.75,0.917 2.917,0.917 true 1.115,1.115 1.115,0.917 false 2.938,0.833 3.25,0.99 0.313,0.156 10 *1
*1 Retainer


Pinch the retainer as shown in the illustration, and then remove the fuel emission hose.

NOTICE:
·

Clean off any dirt and foreign matter from the clip before disconnecting the hoses.

·

Do not use any tools in this procedure.

·

Do not forcefully bend or twist the nylon tube.

·

Put the hose in a plastic bag to prevent damage and contamination.

·

If the connector is stuck, pinch the retainer and push and pull the hose to disconnect it.