Home › Engine / Hybrid System › 2AD-FHV ENGINE MECHANICAL › ENGINE
RM3090E _51 Engine / Hybrid System _008404 2AD-FHV ENGINE MECHANICAL _0046934 ENGINE G

2AD-FHV ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


CAUTION / NOTICE / HINT

HINT:

The type of ignition switch used on this model differs according to the specifications of the vehicle. For the expressions listed in this section, refer to the "Ignition Switch Expressions" precaution.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSPECT ENGINE IDLE SPEED

NOTICE:
·

Turn all the electrical systems and A/C off.

·

Inspect the engine idle speed with the cooling fan off.

·

When checking the idle speed, move the shift lever to neutral.



HINT:
·

For more information about the GTS, refer to its operator's manual.

·

If the GTS is not available, use a tachometer as a substitute.



a.

Warm up and stop the engine.


b.

When using the GTS:

i.

Connect the GTS to the DLC3.


ii.

Start the engine and idle it.


iii.

Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

Powertrain > Engine > Data List
Tester Display
Engine Speed
50003 61 315


c.
A206183C24
0.531,1.729 0.802,1.729 0.802,1.729 1.031,1.49 true 0.042,0.052 0.354,0.208 0.313,0.156 10 *a 0.229,1.635 0.688,1.833 0.458,0.198 10 TAC
*a Front view of DLC3


When not using the GTS:

i.

Connect a tester probe of a tachometer to terminal 9 (TAC) of the DLC3 with SST.

SST
09843-18040  


ii.

Start the engine and idle it.



d.

Inspect the engine idle speed.

Standard idle speed:

750 to 850 rpm



e.

Turn the ignition switch off.


f.

Disconnect the GTS or tachometer tester probe from the DLC3.


Hide 2.INSPECT MAXIMUM ENGINE SPEED

a.

Start the engine.


b.

Fully depress the accelerator pedal.


c.

Check the maximum engine speed.

Maximum engine speed:

5100 to 5250 rpm



Hide 3.INSPECT COMPRESSION

a.

Warm up and stop the engine.


b.

Disconnect the connectors from the injector assemblies.


c.

Remove the glow plug assemblies.

Click hereEngine / Hybrid System>2AD-FHV STARTING>GLOW PLUG>REMOVAL


d.

Inspect the cylinder compression pressure.

i.
A265213C01
1.583,0.802 0.823,0.802 true 0.667,0.719 0.813,0.885 0.146,0.167 10 *1
*1 SST (Attachment)


Insert SST (attachment) into the glow plug hole.

SST
09992-00026  (09992-00121)


ii.
A265214C01
0.271,0.583 0.646,0.583 true 0.115,0.5 0.271,0.656 0.156,0.156 10 *1
*1 SST (Compression Gauge)


Connect SST (compression gauge) to SST (attachment).

SST
09992-00026  (09992-00211)


iii.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

2500 kPa (25.5 kgf/cm2, 362 psi) or higher


Minimum pressure:

2200 kPa (22.5 kgf/cm2, 320 psi)


Difference between each cylinder:

500 kPa (5.0 kgf/cm2, 71 psi) or less


NOTICE:
·

Use a fully-charged battery so the engine speed can be increased to 280 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression as quickly as possible.




iv.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the glow plug holes, and then inspect it again.

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.



e.

Remove SST (attachment and compression gauge).


f.

Install the glow plug assemblies.

Click hereEngine / Hybrid System>2AD-FHV STARTING>GLOW PLUG>INSTALLATION


g.

Connect the connectors to the injector assemblies.