Home › Engine / Hybrid System › 2AD-FHV ENGINE MECHANICAL › ENGINE UNIT
RM3090E _51 Engine / Hybrid System _008404 2AD-FHV ENGINE MECHANICAL _0046940 ENGINE UNIT A

2AD-FHV ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the injectors (including shuffling the injectors between the cylinders), common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the injection pipes with new ones.

·

When replacing the fuel supply pump assembly, common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the fuel inlet pipe with a new one.



PROCEDURE

Hide 23762 1.REMOVE NO. 2 NOZZLE LEAKAGE PIPE

Hide 23761A 2.REMOVE NO. 1 NOZZLE LEAKAGE PIPE

Hide 23695 3.REMOVE NO. 1 NOZZLE HOLDER CLAMP

Hide 23670 4.REMOVE INJECTOR ASSEMBLY

Hide 11301K 5.REMOVE CAMSHAFT POSITION SENSOR

a.
A266026

Remove the bolt and camshaft position sensor.


Hide 11401G 6.REMOVE CRANKSHAFT POSITION SENSOR

a.
A202379

Remove the clip and disconnect the crankshaft position sensor harness.


b.

Remove the 2 bolts and crankshaft position sensor.


Hide 89422C 7.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 16100 8.REMOVE ENGINE WATER PUMP ASSEMBLY

Hide 83530 9.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 15710 10.REMOVE OIL COOLER ASSEMBLY

Hide 15781 11.REMOVE NO. 1 OIL COOLER BRACKET

Hide 89491 12.REMOVE ENGINE OIL LEVEL SENSOR

a.
A129585

Remove the 4 bolts and engine oil level sensor.


Hide 16323 13.REMOVE WATER INLET HOUSING

Hide 12108 14.REMOVE OIL FILLER CAP SUB-ASSEMBLY

Hide 11201 15.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12102A 16.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15677 18.REMOVE OIL FILTER BRACKET

Hide 15104 19.REMOVE OIL STRAINER SUB-ASSEMBLY

Hide 20.SET NO. 1 CYLINDER TO TDC / COMPRESSION

a.
A202382
1.125,0.802 0.49,0.177 0.49,0.177 0.302,0.177 true 1.219,0.865 0.552,1.875 0.552,1.875 0.344,1.875 true 0.125,0.052 0.302,0.229 0.177,0.177 10 *1 0.156,1.75 0.333,1.927 0.177,0.177 10 *2
*1 Timing Pointer
*2 Timing Mark


Turn the crankshaft pulley clockwise to align the timing mark on the crankshaft pulley with the timing pointer of the timing chain cover sub-assembly.


b.
A202383
1.479,0.365 1.698,0.115 1.698,0.115 1.823,0.115 true 1.479,0.552 0.615,0.906 0.615,0.906 0.469,0.906 true 1.865,0.052 2.052,0.229 0.188,0.177 10 *1 0.292,0.823 0.479,1 0.188,0.177 10 *2
*1 Matchmark
*2 Timing Mark


Make sure that the timing mark of the camshaft timing sprocket is at the top.

HINT:

If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 cylinder to TDC/compression).



c.

Put a matchmark on the timing chain plate that is aligned with the timing mark of the camshaft timing sprocket.

HINT:

The timing chain has 2 yellow-colored plates. If either of them is aligned with the timing mark of the camshaft timing sprocket, this step can be omitted.



d.
A202384
1.625,0.167 2.083,0.365 0.458,0.198 10 90°

Turn the crankshaft pulley by approximately 90° in the direction of engine revolution from the point where the No. 1 cylinder is set to TDC/compression so that the lifted valve and piston do not contact each other when removing the camshaft.


Hide 13471 21.REMOVE CRANKSHAFT PULLEY

a.
A201753
1.604,1.917 1.344,2.083 1.344,2.083 1.219,2.083 true 0.354,1.052 0.167,1.51 0.167,1.51 0.167,1.677 true 0.167,1.5 0.385,1.375 true 0.927,2 1.25,2.156 0.323,0.156 10 SST 0.063,1.729 0.385,1.885 0.323,0.156 10 SST

Using SST, loosen the crankshaft pulley bolt.

SST
09213-58014  (91551-80840)
09330-00021  


b.
A201752
0.381,1.22 0.693,1.383 0.313,0.163 10 SST 1.283,1.124 0.857,1.301 0.857,1.301 0.756,1.301 false

Using SST, remove the bolt and crankshaft pulley.

SST
09950-50013  (09951-05010, 09952-05010, 09953-05020, 09954-05021)


Hide 11302 22.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11301C 23.REMOVE FRONT CRANKSHAFT OIL SEAL

Hide 13540 24.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A300900
1.99,1.479 1.802,1.479 1.802,1.479 1.49,1.146 false 1.844,0.625 1.979,0.219 1.979,0.219 1.802,0.219 true 1.021,1.958 1.531,1.958 true 1.635,0.104 1.948,0.26 0.313,0.156 10 false *1 2,1.365 2.313,1.521 0.313,0.156 10 false *2 1.573,1.854 2.031,2.052 0.458,0.198 10 false SST
*1 Plunger
*2 Stopper Plate


Move the stopper plate upward to release the lock, and push the plunger deep into the No. 1 chain tensioner assembly.


b.

Move the stopper plate downward to set the lock, and insert SST into the stopper plate hole.

SST
09240-00020  (09242-00200)


c.
A202387

Remove the 2 bolts and No. 1 chain tensioner assembly.


Hide 13559 25.REMOVE CHAIN TENSIONER SLIPPER

A202388

Hide 13561 26.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A202389

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13523 27.REMOVE CAMSHAFT TIMING SPROCKET

a.
A266025

Remove the 4 bolts from the camshaft timing sprocket while holding the hexagonal portion of the No. 2 camshaft with a wrench.


b.

Remove the camshaft timing sprocket and chain sub-assembly.


Hide 13519 28.REMOVE OIL PUMP DRIVE GEAR

a.
A202391

Remove the oil pump drive gear from the crankshaft.


Hide 13521 29.REMOVE CRANKSHAFT TIMING SPROCKET

a.
A202392

Remove the crankshaft timing sprocket from the crankshaft.


Hide 13471A 30.REMOVE CRANKSHAFT PULLEY SET CRANKSHAFT KEY

a.
A202393

Remove the 2 crankshaft pulley set crankshaft keys from the crankshaft.


Hide 13801 32.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

Hide 13750 33.REMOVE VALVE LASH ADJUSTER ASSEMBLY

Hide 11101 34.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11115 35.REMOVE CYLINDER HEAD GASKET

Hide 12216G 37.REMOVE OIL BAFFLE PLATE

a.
A202405

Remove the 2 bolts and oil baffle plate.


Hide 13620B 38.REMOVE ENGINE BALANCER ASSEMBLY

a.
A202403
1.656,0.677 1.229,0.521 1.229,0.521 1.073,0.521 true 1.604,1.594 2.906,1.594 true 1.5,1.917 2.365,1.917 2.365,1.917 2.365,1.594 true 0.885,0.427 1.083,0.615 0.198,0.188 10 false *1 2.906,1.479 3.167,1.677 0.26,0.198 10 true *2
*1 Service Bolt
*2 Timing Mark


Align the timing marks (1 dot mark each) of the drive and driven gears by turning the crankshaft with a wrench.


b.

Put matchmarks on the drive gear and driven gear.


c.

Install a service bolt.

Recommended Service Bolt:
Item Specified Condition
Thread diameter 6 mm (0.236 in.)
Thread pitch 1 mm (0.0394 in.)
Bolt length 16 to 18 mm (0.630 to 0.709 in.)


Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)

HINT:

When removing the balancer, make sure that the torsional spring force of the sub gear has been eliminated by the installation of the service bolt.



d.
A273384
0.896,0.063 1.083,0.26 0.188,0.198 10 1 0.698,1.781 0.885,1.979 0.188,0.198 10 2 2.479,0.063 2.667,0.26 0.188,0.198 10 3 2.604,1.802 2.792,2 0.188,0.198 10 4 1.333,0.042 1.521,0.24 0.188,0.198 10 5 1.927,1.938 2.115,2.135 0.188,0.198 10 6 1.813,0.021 2,0.219 0.188,0.198 10 7 1.281,1.979 1.469,2.177 0.188,0.198 10 8

Uniformly loosen the 8 bolts in several steps, in the sequence shown in the illustration.


e.

Remove the engine balancer assembly.


Hide 11415 39.REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

a.
A263734

Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.