The type of ignition switch used on this model differs according to the specifications of the vehicle. For the expressions listed in this section, refer to the "Ignition Switch Expressions" precaution.
Click hereEngine / Hybrid System>3ZR-FE STARTING>STARTING SYSTEM>PRECAUTION
1.INSPECT ENGINE COOLANT
2.INSPECT ENGINE OIL
28800
3.INSPECT BATTERY
17801
4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner cap sub-assembly.
Remove the air cleaner filter element sub-assembly.
Visually check that the air cleaner filter element sub-assembly is not excessively damaged or oily.
If necessary, replace the air cleaner filter element sub-assembly.
19100P
5.INSPECT SPARK PLUG
16361A
6.INSPECT V-RIBBED BELT
13750
7.INSPECT VALVE LASH ADJUSTER NOISE
Rev up the engine several times. Check that the engine does not emit unusual noises.
If unusual noises occur, warm up the engine and idle it for over 30 minutes. Then perform the inspection above again.
If any defects or problems are found during the inspection above, perform a lash adjuster inspection.
Click hereEngine / Hybrid System>3ZR-FE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION
8.INSPECT IGNITION TIMING
Warm up and stop the engine.
When using the GTS:
Connect the GTS to the DLC3.
Start the engine and idle it.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.
| Tester Display |
|---|
| IGN Advance |
0 to 14° BTDC @ idle
Turn all the electrical systems and the A/C off.
Check the ignition timing with the cooling fan off.
When checking the ignition timing, the shift lever should be in N or P.
Refer to the GTS operator's manual for further details.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
| Tester Display |
|---|
| Connect the TC and TE1 |
Monitor IGN Advance of the Date List.
8 to 12 BTDC @ idle
Turn all the electrical system and A/C off.
Check the ignition timing with the cooling fan off.
When checking the ignition timing, the shift lever should be in N or P.
Check that the ignition timing advances immediately when the engine speed is increased.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
When not using the GTS:
Remove the No. 2 cylinder head cover.
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
Use a timing light that detects primary signals.
Start the engine and idle it.
| *a | Front view of DLC3 |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
When checking the ignition timing, the shift lever should be in N or P.
Using the timing light, check the ignition timing.
8 to 12° BTDC @ idle
Turn all the electrical systems and the A/C off.
Check the ignition timing with the cooling fan off.
When checking the ignition timing, the shift lever should be in N or P.
Remove SST from the DLC3.
Inspect the ignition timing at idle.
0 to 14° BTDC @ idle
Turn all the electrical systems and the A/C off.
Check the ignition timing with the cooling fan off.
When checking the ignition timing, the shift lever should be in N or P.
Check that the ignition timing advances immediately when the engine speed is increased.
Turn the ignition switch off.
Remove the timing light.
Install the No. 2 cylinder head cover.
9.INSPECT ENGINE IDLE SPEED
Warm up and stop the engine.
When using the GTS:
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
600 to 700 rpm
Turn all the electrical systems and the A/C off.
Check the ignition timing with the cooling fan off.
When checking the idling speed, the shift lever should be in N or P.
Refer to the GTS operator's manual for further details.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
| *a | Front view of DLC3 |
When not using the GTS:
Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.
Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
When checking the idling speed, the shift lever should be in N or P.
Turn all the electrical systems and the A/C off.
Check the ignition timing with the cooling fan off.
Check the idle speed.
600 to 700 rpm
Disconnect the tachometer probe from the DLC3.
10.INSPECT COMPRESSION
Warm up and stop the engine.
Check for DTCs.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
Remove the 4 spark plugs.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>REMOVAL
Disconnect the 4 fuel injector connectors.
Inspect the cylinder compression pressure.
Insert a compression gauge into the spark plug hole.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
1373 kPa (14.0 kgf/cm2, 199 psi) or higher
1079 kPa (11.0 kgf/cm2, 156 psi)
98 kPa (1.0 kgf/cm2, 14.2 psi) or less
Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.
Inspect the other cylinders in the same way.
Measure the compression in as short a time as possible.
If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole, and then inspect it again.
If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.
Connect the 4 fuel injector connectors.
Install the 4 spark plugs.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>IGNITION COIL AND SPARK PLUG>INSTALLATION
Clear the DTCs.
Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
11.INSPECT CO/HC
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe while idling.
Check the CO/HC concentration during idling and when the engine is running at 2500 rpm.
When doing the 2 mode (with the engine idling/running at 2500 rpm) test, the measuring procedures are determined by applicable local regulations.
If the CO/HC concentration does not comply with the regulations, troubleshoot in the order given below.
Check the air fuel ratio sensor (Click here Engine / Hybrid System>3ZR-FE ENGINE CONTROL>AIR FUEL RATIO SENSOR>INSPECTION) and heated oxygen sensor operation (Click here Engine / Hybrid System>3ZR-FE ENGINE CONTROL>HEATED OXYGEN SENSOR>INSPECTION).
See the table below for possible causes, and then inspect the applicable parts and repair them if necessary.
| CO | HC | Problems | Possible Causes |
|---|---|---|---|
| Normal | High | Rough idling | 1.
Faulty ignition: ·
Incorrect timing ·
Fouled, shorted or improperly gapped plugs 2.
Leakage from intake or exhaust valves 3.
Leakage from cylinders |
| Low | High | Rough idling
(Fluctuating HC reading) |
1.
Vacuum leaks: ·
PCV hoses ·
Intake manifold ·
Throttle body ·
Brake booster line 2.
Lean mixture causing misfire |
| High | High | Rough idling
(Black smoke from exhaust) |
1.
Restricted air cleaner filter element 2.
Plugged PCV valve 3.
Faulty SFI system: ·
Faulty pressure regulator ·
Faulty engine coolant temperature sensor ·
Faulty mass air flow meter ·
Faulty ECM ·
Faulty injectors ·
Faulty throttle body |