Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › ENGINE UNIT
RM3090E _51 Engine / Hybrid System _008405 3ZR-FE ENGINE MECHANICAL _0046950 ENGINE UNIT A

3ZR-FE ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


PROCEDURE

Hide 16268 4.INSTALL NO. 1 WATER BY-PASS PIPE

a.

Install the No. 1 water by-pass pipe with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16262 5.INSTALL WATER INLET HOSE

a.

Install the water inlet hose to the water inlet housing and No. 1 water by-pass pipe, and slide the 2 clamps to secure the hoses.


Hide 16261 6.INSTALL WATER BY-PASS HOSE

a.

Install the water by-pass hose to the No. 1 water by-pass pipe, and slide the clamp to secure the hose.


Hide 16267 7.CONNECT NO. 3 WATER BY-PASS HOSE

a.

Connect the No. 3 water by-pass hose to the water inlet housing, and slide the clamp to secure hose.


Hide 12261 8.INSTALL PCV HOSE

a.

Install the PCV hose to the PCV valve, and slide the clamp to secure hose.


Hide 11492D 9.INSTALL NO. 1 SEAL PLATE (for Manual Transaxle)

a.

Install the No. 1 seal plate and a new gasket with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16279 10.INSTALL NO. 3 WATER BY-PASS PIPE (for CVT)

a.

Install the No. 3 water by-pass pipe and a new gasket with the 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17167 13.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Hide 11452 14.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Install the engine oil level dipstick guide with the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Install the engine oil level dipstick.


Hide 23250 15.INSTALL FUEL INJECTOR ASSEMBLY

Hide 23807 16.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

Hide 23901 17.INSTALL FUEL TUBE SUB-ASSEMBLY

Hide 25719 18.INSTALL VACUUM SURGE TANK

Hide 17111 19.INSTALL INTAKE MANIFOLD

a.

Install a new gasket to the intake manifold.


b.

Install the intake manifold and intake manifold stay with the 5 bolts and 2 nuts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


c.

Connect the PCV hose to the intake manifold, and slide the clamp to secure the hose.


d.

Connect the 2 water by-pass hoses to the intake manifold and No. 1 water by-pass pipe, and slide the 2 clamps to secure the hoses.


e.

Connect the air tube with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 87245A 20.INSTALL HEATER WATER INLET HOSE

a.

Install the heater water inlet hose to the No. 1 water by-pass pipe, and slide the clamp to secure hose.


Hide 87246A 21.INSTALL HEATER WATER OUTLET HOSE

a.

Install the heater water outlet hose to the cylinder head sub-assembly, and slide the clamp to secure hose.