Home › Engine / Hybrid System › 3ZR-FE FUEL › FUEL INJECTOR › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _008406 3ZR-FE FUEL _0046953 FUEL INJECTOR A

3ZR-FE FUEL  FUEL INJECTOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

Perform "Inspection After Repairs" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 23250 1.INSTALL FUEL INJECTOR ASSEMBLY

HINT:

Perform "Inspection After Repairs" after replacing the fuel injector assembly.

Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION


a.
A153011C09
1.063,0.385 0.729,0.385 false 2.031,1.365 2.385,1.365 false 0.521,0.292 0.708,0.469 0.188,0.177 10 *1 2.406,1.26 2.594,1.438 0.188,0.177 10 *2
*1 O-Ring
*2 Injector Vibration Insulator


Install a new injector vibration insulator and a new O-ring to each fuel injector assembly.


b.

Apply a light coat of gasoline or spindle oil to the O-ring of the fuel injector assembly.


c.
A153013

While turning the fuel injector assembly left and right, install it to the fuel delivery pipe sub-assembly.

NOTICE:
·

Do not twist the O-ring.

·

After installing the fuel injectors, check that they turn smoothly. If not, replace the O-ring with a new one.




Hide 23807 2.INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

a.
A153008

Install the 2 No. 1 delivery pipe spacers to the cylinder head.

NOTICE:

Install the No. 1 delivery pipe spacers in the correct direction.



b.

Install the fuel delivery pipe sub-assembly with the 4 fuel injector assemblies, and then temporarily install the 2 bolts.

NOTICE:
·

Do not drop the fuel injector assemblies when installing the fuel delivery pipe sub-assembly.

·

Check that the fuel injector assemblies rotate smoothly after installing the fuel delivery pipe sub-assembly.




c.

Tighten the 2 bolts to the specified torque.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


d.

Install the bolt to secure the fuel delivery pipe sub-assembly.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


e.

Install the wire harness bracket with the bolt.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 23901 3.CONNECT FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly, and then install a new No. 2 fuel pipe clamp.

Click hereEngine / Hybrid System>3ZR-FE FUEL>FUEL SYSTEM>PRECAUTION


Hide 25719 4.INSTALL VACUUM SURGE TANK

a.
A298980C01
1.656,3.083 2.031,3.219 2.031,3.219 2.167,3.219 false 2.188,3.125 2.5,3.281 0.313,0.156 10 *1 0.75,2.563 1.063,2.719 0.313,0.156 10 *a 1.365,3.146 1.677,3.302 0.313,0.156 10 *b 1.031,1.51 1.188,1.708 0.156,0.198 10 A
*1 Paint Mark
*a Front Side of Vehicle
*b LH Side


Install the vacuum surge tank with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

Connect the 2 air hoses to the purge VSV and intake manifold and attach the clamp.

HINT:

Connect the air hose labeled A so that the paint mark is positioned as shown in the illustration.



Hide 17361M 5.INSTALL AIR TUBE

a.

Install the air tube with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 1 fuel vapor feed hose to the air tube.


c.

Connect the No. 1 vacuum transmitting hose to the air tube and slide the clamp to secure it.


d.

Connect the union to connector tube hose to the air tube and slide the clamp to secure it.


e.

Connect the fuel vapor feed hose to the purge VSV and slide the clamp to secure it.


Hide 82121 6.CONNECT ENGINE WIRE

a.

Attach the 9 clamps and connect the 18 connectors.


b.

Connect the engine wire with the 3 bolts and 3 nuts.

Torque:
for bolt A : 7.7 N*m (79 kgf*cm, 68 in.*lbf)
for bolt B and nut : 8.4 N*m (86 kgf*cm, 74 in.*lbf)

A298981N01
2.313,1.594 2.469,1.792 0.156,0.198 10 A 1.979,5.281 2.177,5.448 0.198,0.167 10 B 2.719,5.5 2.917,5.667 0.198,0.167 10 B


Hide 74431 7.INSTALL BATTERY TRAY

Hide 28800 8.INSTALL BATTERY

Hide 74404A 9.INSTALL BATTERY CLAMP SUB-ASSEMBLY

Hide 10.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17705 11.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 12.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 13.INSPECT FOR FUEL LEAK

a.

Make sure that there are no fuel leaks after performing maintenance on the fuel system.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON, and GTS on.

NOTICE:

Do not start the engine.



iii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

iv.

Check that there are no leaks from the fuel system.


v.

Turn the ignition switch off.


vi.

Disconnect the GTS from the DLC3.



Hide 11212 14.INSTALL NO. 2 CYLINDER HEAD COVER