Home › Engine / Hybrid System › 3ZR-FE FUEL › FUEL SYSTEM
RM3090E _51 Engine / Hybrid System _008406 3ZR-FE FUEL _0046954 FUEL SYSTEM G

3ZR-FE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK

a.

Check the fuel pump operation.

i.

Connect the GTS to the DLC3.


ii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

v.

Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the C/OPN relay, fuel pump, ECM and wiring connectors.



b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs. If there is a fuel leak, repair or replace parts as necessary.



c.

Turn the ignition switch off.


d.

Disconnect the GTS from the DLC3.


Hide 2.CHECK FUEL PRESSURE

a.

Using a voltmeter, measure the battery voltage.

Click herePower Source / Network>3ZR-FE BATTERY / CHARGING>CHARGING SYSTEM>PRECAUTION


b.

Discharge the fuel system pressure.

Click hereEngine / Hybrid System>3ZR-FE FUEL>FUEL SYSTEM>PRECAUTION


c.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION




d.

Disconnect the fuel tube sub-assembly from the fuel pipe.

Click hereEngine / Hybrid System>3ZR-FE FUEL>FUEL SYSTEM>PRECAUTION


e.
A349783C01
0.583,1.417 0.75,1 0.75,1 0.917,1 false 1.583,2.417 1.75,2.417 1.75,2.417 2,2.021 false 2.417,0.5 2.583,0.5 2.583,0.5 2.813,0.344 false 2.25,1.083 2.417,1.083 2.417,1.083 2.667,0.927 false 2.333,1.417 2.5,1.417 2.5,1.417 2.729,1.521 false 2.635,2.917 2.917,2.667 2.917,2.667 3.083,2.667 false 0.667,3.333 0.833,3.333 0.833,3.333 1.083,3.104 false 0.667,4.083 0.833,4.083 0.833,4.083 1.135,3.917 false 0.938,0.917 1.25,1.073 0.313,0.156 10 false *1 1.417,2.344 1.729,2.5 0.313,0.156 10 false *2 3.104,2.583 3.333,2.75 0.229,0.167 10 false *3 2.083,1 2.396,1.156 0.313,0.156 10 false *4 0.5,4 0.813,4.156 0.313,0.156 10 false *5 2.25,0.417 2.563,0.573 0.313,0.156 10 false *6 2.167,1.333 2.479,1.49 0.313,0.156 10 false *6 0.5,3.26 0.813,3.417 0.313,0.156 10 false *6
*1 SST (Pressure Gauge)
*2 SST (Hose Joint)
*3 SST (Hose)
*4 SST (T Joint)
*5 SST (Fuel Tube Connector)
*6 SST (Hose Band)


Install SST (pressure gauge) as shown in the illustration.

SST
09268-45101  (09268-41260, 09268-41280, 09268-41700, 95336-08070)
09268-00010  (09268-00020, 09268-00030)


f.

Clean up any spilled gasoline.


g.

Connect the cable to the negative (-) battery terminal.


h.

Connect the GTS to the DLC3.


i.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230

j.

Measure the fuel pressure.

Standard fuel pressure:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)


·

If the fuel pressure is higher than the standard value, replace the fuel pressure regulator.

·

If the fuel pressure is less than the standard value, check the fuel hoses and connections, fuel pump, fuel filter and fuel pressure regulator.



k.

Disconnect the GTS from the DLC3.


l.

Start the engine.


m.

Measure the fuel pressure at idle.

Standard fuel pressure:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)



n.

Stop the engine.


o.

Check that the fuel pressure remains as specified for 5 minutes after the engine stops.

Standard fuel pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or higher


If the fuel pressure is not as specified, check the fuel pump or fuel injector.


p.

After checking the fuel pressure, disconnect the cable from the negative (-) battery terminal and carefully remove SST to prevent gasoline from spraying.


q.

Reconnect the fuel tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>3ZR-FE FUEL>FUEL SYSTEM>PRECAUTION


r.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


s.

Connect cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION