Home › Engine / Hybrid System › 3ZR-FE ENGINE MECHANICAL › ENGINE ASSEMBLY › 2012.12–2013.11
RM3090E _51 Engine / Hybrid System _008405 3ZR-FE ENGINE MECHANICAL _0046949 ENGINE ASSEMBLY A

3ZR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  REMOVAL  


CAUTION / NOTICE / HINT

CAUTION:

As the engine assembly with transaxle is extremely heavy, the engine lifter may suddenly drop if the instructions listed in the repair manual are not followed.

Therefore, always follow the instructions listed in the repair manual when performing this procedure.


NOTICE:

for Manual Transaxle:

When the transaxle is removed, be sure to use a new clutch release with bearing cylinder assembly and new installation bolts. Removal of the transaxle allows the compressed clutch release with bearing cylinder assembly to return to its original position, and dust could damage the seal of the clutch release with bearing cylinder assembly, possibly causing clutch fluid leaks.


PROCEDURE

Hide 1.DISCHARGE FUEL SYSTEM PRESSURE

Hide 11212 2.REMOVE NO. 2 CYLINDER HEAD COVER

Hide 3. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 5.DISCONNECT CABLE FROM POSITIVE BATTERY TERMINAL

Hide 6.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 51441 7.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51443 8.REMOVE REAR ENGINE UNDER COVER RH

a.
A297336

Remove the 3 clips and rear engine under cover RH.


Hide 51444 9.REMOVE REAR ENGINE UNDER COVER LH

A296295

a.

Remove the 3 clips and rear engine under cover LH.


Hide 13.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID (for CVT)

Hide 16470 15.REMOVE RADIATOR RESERVOIR ASSEMBLY

a.
A292528

Slide the 2 clamps and disconnect the No. 1 and No. 2 water by-pass hoses from the radiator reservoir assembly.


b.

Remove the 2 bolts and radiator reservoir assembly.


Hide 16572D 18.DISCONNECT NO. 2 RADIATOR HOSE

a.
A292532

Slide the clamp and disconnect the No. 2 radiator hose from the water inlet.


Hide 88310 19.DISCONNECT COMPRESSOR WITH PULLEY ASSEMBLY

a.
A292529

Disconnect the connector.


b.
A292530

Remove the 2 bolts and 2 nuts.


c.
A292531

Using an E8 "TORX" socket wrench, remove the 2 stud bolts and disconnect the compressor with pulley assembly.

HINT:

It is not necessary to completely remove the compressor. With the hoses connected to the compressor, hang the compressor on the vehicle body with a rope.



Hide 17705 20.REMOVE AIR CLEANER CAP SUB-ASSEMBLY

Hide 21.REMOVE AIR CLEANER CASE SUB-ASSEMBLY

Hide 74404A 22.REMOVE BATTERY CLAMP SUB-ASSEMBLY

Hide 28800 23.REMOVE BATTERY

Hide 74431 24.REMOVE BATTERY TRAY

Hide 16057 25.DISCONNECT RADIATOR HOSE SUB-ASSEMBLY

Hide 74411B 26.REMOVE FRONT BATTERY BRACKET

Hide 74414B 27.REMOVE BATTERY BRACKET REINFORCEMENT

Hide 16571 29.DISCONNECT NO. 1 RADIATOR HOSE

a.
A300873

for CVT:

Disconnect the breather plug hose from the clamp.


b.
A292533

Slide the clamp and disconnect the No. 1 radiator hose from the cylinder head.


Hide 23901 30.DISCONNECT FUEL TUBE SUB-ASSEMBLY

a.
A298964

Remove the No. 1 fuel pipe clamp, and then disconnect the fuel tube sub-assembly.

Click hereEngine / Hybrid System>3ZR-FE FUEL>FUEL SYSTEM>PRECAUTION


Hide 31.DISCONNECT WIRE HARNESS AND HOSE

a.
A292534

Detach the 2 clamps and remove the bolt.


b.
A292536

Disconnect the 2 connectors and remove the nut.


c.
A292537

Detach the 2 claws and slide the wire harness, and then disconnect the wire harness.


d.
A270920

Disconnect the terminal cap, and then remove the nut and disconnect the starter wire.


e.

Detach the wire harness clamp.


f.
A292539

for Manual Transaxle:

Detach the clamp, remove the bolt and disconnect the engine wire from the manual transaxle.


g.
A270921

for CVT:

Detach the clamp, remove the bolt and disconnect the engine wire from the CVT.


h.
A292538

Slide the clamp and disconnect the connector tube hose from the air tube.


i.
A209171

Slide the 2 clamps and disconnect the heater water outlet hose and heater water inlet hose from the heater core.


Hide 33820B 32.DISCONNECT TRANSAXLE CONTROL CABLE ASSEMBLY (for Manual Transaxle)

a.
C277986

Remove the 2 clips and disconnect the top ends of the transaxle control cable assembly from the transaxle.


b.

Remove the 2 clips and disconnect the transaxle control cable assembly from the control cable bracket.


Hide 33.DISCONNECT TRANSAXLE CONTROL CABLE ASSEMBLY (for CVT)

a.
C203394

Remove the nut and disconnect the transaxle control cable assembly from the control shaft lever.


b.

Remove the clip and disconnect the transaxle control cable assembly from the control cable bracket.


c.
C201443

Disconnect the transaxle control cable assembly from the control cable support.


d.
C131876

Remove the bolt and disconnect the clamp of the control cable.


Hide 34.DISCONNECT CLUTCH HOSE (for Manual Transaxle)

a.
A296890

Using a 10 mm union nut wrench, disconnect the clutch hose from the accumulator to flexible hose tube.


b.

Remove the clip and disconnect the clutch hose.


Hide 45259A 35.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 36.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 37.DISCONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 43502H 38.REMOVE FRONT AXLE SHAFT NUT LH

Hide 43501H 39.REMOVE FRONT AXLE SHAFT NUT RH

HINT:

Use the same procedure described for the LH side.


Hide 40.DISCONNECT FRONT SPEED SENSOR LH

Hide 41.DISCONNECT FRONT SPEED SENSOR RH

HINT:

Use the same procedure described for the LH side.


Hide 48810 42.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 43.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45047 44.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 45.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 46.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 47.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 43420G 49.REMOVE FRONT DRIVE SHAFT HOLE SNAP RING

Hide 17410 51.REMOVE FRONT EXHAUST PIPE ASSEMBLY

Hide 89465 52.DISCONNECT HEATED OXYGEN SENSOR (for 4WD/AWD)

Hide 37100 53.REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)

Hide 32101A 54.REMOVE DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT (for CVT)

Hide 51425B 55.REMOVE FRONT LOWER ENGINE MOUNTING BRACKET REINFORCEMENT (for 2WD)

a.
A295897

Remove the 2 bolts and front lower engine mounting bracket reinforcement.


Hide 51218A 56.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.
A296303

Remove the 4 bolts and front suspension member reinforcement LH.


Hide 51217A 57.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.
A296302

Remove the 4 bolts and front suspension member reinforcement RH.


Hide 58.INSTALL ENGINE HANGER

a.
A292543

Detach the fuel tube clamp.


b.

Disconnect the air fuel ratio sensor connector and remove the bolt and air fuel ratio sensor bracket.


c.
A150573C04
0.333,0.677 0.458,0.677 0.458,0.677 0.74,0.823 true 1.75,0.25 1.833,0.25 1.833,0.25 2.615,0.583 true 0.135,0.583 0.417,0.833 0.281,0.25 10 *1 1.552,0.167 1.833,0.333 0.281,0.167 10 *2
*1 No. 1 Engine Hanger
*2 No. 2 Engine Hanger


Install the 2 engine hangers with 2 bolts as shown in the illustration.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
No. 1 Engine Hanger 12281-37021
No. 2 Engine Hanger 12282-37011
Bolt 91552-81050



Hide 59.REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

a.
A296304

Remove the 6 bolts and front crossmember sub-assembly.


b.
A292540C01
0.021,0.083 0.333,0.24 0.313,0.156 10 *A 0.083,2.417 0.396,2.573 0.313,0.156 10 *B
*A for Manual Transaxle
*B for CVT


Remove the through bolt, nut and front engine mounting insulator.

NOTICE:

While holding the nut in place, loosen the through bolt.



c.

Set an engine lifter underneath the engine.

NOTICE:

Place the engine on wooden blocks or equivalent so that the engine is level.



d.
A292541

Remove the bolt and 2 nuts, and disconnect the engine mounting insulator RH.


e.
A292542C01
0.083,0.083 0.396,0.24 0.313,0.156 10 *A 0.104,2.344 0.417,2.5 0.313,0.156 10 *B
*A for Manual Transaxle
*B for CVT


Remove the bolt and nut, and disconnect the engine mounting insulator LH.


f.
A296308

Remove the 6 bolts and front suspension member brace rear RH and LH.


g.
A296309

Remove the 2 bolts and front suspension crossmember sub-assembly.


h.

Operate the engine lifter and slowly remove the engine from the vehicle.

NOTICE:
·

Make sure that the engine is clear of all wiring and hoses.

·

While lowering the engine from the vehicle, do not allow it to contact the vehicle.




i.

Attach an engine sling device and hang the engine with a chain block.


j.
A298936

Remove the through bolt and front suspension crossmember from the engine with transaxle.

NOTICE:

Do not damage any engine or transaxle components.


HINT:

Raise the engine with transaxle assembly while keeping it level.



Hide 45319A 60.REMOVE STEERING GEAR HEAT INSULATOR (for RHD)

Hide 11363A 62.REMOVE FLYWHEEL HOUSING SIDE COVER

Hide 36100 63.REMOVE TRANSFER ASSEMBLY (for 4WD/AWD)

Hide 30400 64.REMOVE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY (for CVT)

Hide 30300 65.REMOVE MANUAL TRANSAXLE ASSEMBLY (for Manual Transaxle)

Hide 66.FIX ENGINE ASSEMBLY

a.

Using wooden blocks or plate lift attachments, set the engine on a flat surface.

NOTICE:
·

Place wooden blocks or plate lift attachments so that the engine is level.

·

Never install attachments to the oil pan of the engine assembly or transaxle as doing so may deform the oil pan.

·

Perform this step while supporting the engine assembly using a sling device and chain block.




Hide 32101 67.REMOVE DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

Hide 31210 68.REMOVE CLUTCH COVER ASSEMBLY (for Manual Transaxle)

Hide 31250 69.REMOVE CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 70.REMOVE CLUTCH TUBE (for Manual Transaxle)

Hide 31407B 71.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY (for Manual Transaxle)

Hide 31400 72.REMOVE CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY (for Manual Transaxle)

Hide 13405 73.REMOVE FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

Hide 74.REMOVE ENGINE WIRE

a.

Remove the engine wire from the engine.


Hide 75.INSTALL ENGINE TO ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine while it is suspended, as doing so is dangerous.



a.

Install the engine to an engine stand with the bolts.


b.

Remove the 2 bolts and 2 engine hangers.


Hide 43457 76.REMOVE DRIVE SHAFT BEARING BRACKET

A298937

a.

Remove the 3 bolts and drive shaft bearing bracket.


Hide 12371A 77.REMOVE REAR ENGINE MOUNTING INSULATOR

HINT:

Perform this procedure only when replacement of the rear engine mounting insulator is necessary.


a.

Remove the 2 bolts, 2 nuts and rear engine mounting insulator.

A293519C01
0.354,0.094 0.667,0.25 0.313,0.156 10 *A 0.354,1.438 0.667,1.594 0.313,0.156 10 *B 1.188,0.188 1.5,0.344 0.313,0.156 10 *C 3.417,0.188 3.729,0.344 0.313,0.156 10 *D 1.188,1.51 1.5,1.667 0.313,0.156 10 *C 3.438,1.51 3.75,1.667 0.313,0.156 10 *D
*A for 2WD *B for 4WD / AWD
*C for Manual Transaxle *D for CVT



Hide 12305 78.REMOVE ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator is necessary.


a.
A293520

Remove the bolt and radiator reservoir bracket.


b.

Remove the 3 bolts and engine mounting insulator sub-assembly RH.


Hide 12372A 79.REMOVE ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator is necessary.


a.
A293521

Remove the bolt and wire harness clamp bracket.


b.

Remove the 4 bolts and engine mounting insulator LH.