The TCM uses the vehicle speed signal and signals from the transmission speed sensors (NC, NT) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear).
Then the TCM compares the actual gear with the shift schedule in the TCM memory to detect mechanical problems of the shift solenoid valves and valve body.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0746 | Pressure Control Solenoid "A" Performance (Shift Solenoid Valve SL1) | Either condition is met (2-trip detection logic):
·
The engine revs freely when a shift to 1st, 2nd, 3rd or 4th gear is commanded. ·
Either condition is met twice: ·
When a shift to 5th gear is commanded, 4th gear is engaged. ·
When a shift to 6th gear is commanded, 4th gear is engaged. |
·
Shift solenoid valve SL1 remains open or closed ·
Transmission valve body assembly is blocked ·
Automatic transaxle assembly (clutch, brake, gear, etc.) |
Comes on | DTC stored |
The TCM commands gear shifts by turning the shift solenoid valves on and off. According to the input shaft speed, intermediate (counter) shaft speed and output shaft speed, the TCM detects the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear). When the gear commanded by the TCM and the actual gear are not the same, the TCM illuminates the MIL and stores the DTC.
Perform registration and/or initialization when parts related to the automatic transaxle are replaced.
Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
|---|---|
| Only P0746 is output | A |
| P0746 and other DTCs are output | B |
If shift solenoid valve SL1 is stuck off, DTCs for several shift solenoid valves including the malfunctioning shift solenoid valve will be stored.
A
B
This test should always be performed with at least 2 people.
Warm up the engine.
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the GTS, perform the Active Test.
Comparing the gear commanded by the Active Test with the actual gear enables confirmation of the problem.
Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>FAIL-SAFE CHART
The gear commanded by the TCM is shown in the Data List / Shift Status display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Shift Position | Operate the shift solenoid valves and set each shift position | ·
Press "→" button: Shift up ·
Press "←" button: Shift down |
Can be used to check the operation of the shift solenoid valves.
A 10-second interval is required between gear changes. Do not down-shift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition] 50 km/h (30 mph) or less |
| Active Test Display |
|---|
| Control the Shift Position |
| Data List Display |
|---|
| Shift Status |
This test can be conducted when the vehicle is stopped.
When shifting gears using the Active Test function, do not operate the accelerator pedal for 2 seconds before and after shifting gears.
Check the vehicle speed and gear when the engine speed is 1000 rpm.
Because the torque converter has not engaged, it may be difficult to obtain the speeds specified in 4th, 5th and 6th gear, however a difference of speed should still be evident following each gear change.
| 1st | 2nd | 3rd | 4th | 5th | 6th |
|---|---|---|---|---|---|
| 8 to 12 km/h (5 to 7.5 mph) | 15 to 19 km/h (9.3 to 11.8 mph) | 21 to 25 km/h (13.0 to 15.5 mph) | 31 to 35 km/h (19.3 to 21.7 mph) | 44 to 48 km/h (27.3 to 29.8 mph) | 52 to 56 km/h (32.3 to 34.8 mph) |
Compare the TCM commanded gear and the actual gear.
| System Condition | TCM Gear Shift Command | Proceed to | ||||||
|---|---|---|---|---|---|---|---|---|
| 1st | 2nd | 3rd | 4th | 5th | 6th | |||
| Malfunction | Shift solenoid valve SL1 stuck ON | 1st | 2nd | 3rd | 4th | 4th | 4th | A |
| Shift solenoid valve SL1 stuck OFF | N*1 | N*1 | N*1 | N*1 | 5th | 6th | ||
| Shift solenoid valve SL2 stuck ON | 4th | 4th | 4th | 4th | 5th | 6th | B | |
| Shift solenoid valve SL2 stuck OFF | 1st | 2nd | 3rd | 1st | N*1 | N*1 | ||
| Shift solenoid valve SL3 stuck ON | 2nd | 2nd | 3rd | 4th | 5th | 6th | C | |
| Shift solenoid valve SL3 stuck OFF | 1st | 1st | 3rd | 4th | 5th | N*1 | ||
| Shift solenoid valve SL4 stuck ON*3 | 3rd | 3rd | 3rd | 4th | 5th | 5th | D | |
| Shift solenoid valve SL4 stuck OFF | 1st | 2nd | 1st | 4th | N*1 | 6th | ||
| Shift solenoid valve SLT stuck ON | N*2 | N*2 | N*2 | N*2 | N*2 | N*2 | E | |
| Shift solenoid valve SLT stuck OFF*3 | 1st | 2nd | 3rd | 4th | 5th | 6th | ||
*1: Neutral
*2: If shift solenoid valve SLT is stuck on, the line pressure will be low. Therefore, the amount of torque that can be transmitted by each gear is lower than the normal limit. When the engine power exceeds this lowered limit, the engine speed will increase freely.
*3: When shift solenoid valve SLT is stuck off, gear shifting is normal.
A
B
C
D
E
| *1 | Shift Solenoid Valve SL1 |
Remove shift solenoid valve SL1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
|---|---|
·
Battery positive (+) with a 21 W bulb → Terminal 1 ·
Battery negative (-) → Terminal 2 |
Valve moves and makes an operating noise |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the transmission valve body assembly.
Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>VALVE BODY ASSEMBLY>DISASSEMBLY
There are no foreign objects on any valve.
| Proceed to |
|---|
| OK |
| NG |
OK
NG