Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE SYSTEM
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047080 AUTOMATIC TRANSAXLE SYSTEM C

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE SYSTEM  P0705  Transmission Range Sensor Circuit Malfunction (PRNDL Input)  


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the TCM.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) Either condition is met:
(A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
·

NSW input signal is on.

·

R input signal is on.

·

D input signal is on.


(B) NSW, R and D switches are all off simultaneously.
·

Open or short in park/neutral position switch circuit

·

Park/neutral position switch

·

TCM


Comes on DTC stored

MONITOR DESCRIPTION

This DTC indicates a problem with the park/neutral position switch and/or the wire harness in the park/neutral position switch circuit.

The park/neutral position switch detects the shift lever position (P, R or D) and sends a signal to the TCM.

For safety, the park/neutral position switch detects the shift lever position so that the engine cannot be started when the shift lever is not in P or N.

The park/neutral position switch assembly sends a signal to the TCM according to the shift lever position (R or D). The TCM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The TCM will turn on the MIL and store the DTC.

CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click hereDrivetrain>U660F AUTOMATIC TRANSMISSION / TRANSAXLE>AUTOMATIC TRANSAXLE SYSTEM>PRECAUTION


DATA LIST


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Turn the GTS on.


f.

Enter the following menus: Powertrain / ECT / Data List.


g.

According to the display on the GTS, read the Data List.

Powertrain > ECT > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Neutral Position SW Signal PNP switch status ON or OFF
·

ON: Shift lever in P or N

·

OFF: Shift lever not in P or N


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range) PNP switch status ON or OFF
·

ON: Shift lever in R

·

OFF: Shift lever not in R


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (D Range) PNP switch status ON or OFF
·

ON: Shift lever in D or M

·

OFF: Shift lever not in D or M


When the shift lever position displayed on the GTS differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Powertrain > ECT > Data List
Tester Display
Neutral Position SW Signal
Shift SW Status (R Range)
Shift SW Status (D Range)
50003 64 206,166,167


PROCEDURE

1.CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE)
a.
C197711
0.292,0.885 0.729,1.146 0.438,0.26 1.625,1 1.375,0.406 true 0.354,0.927 0.729,1.156 0.375,0.229 10 B36 0.083,0.125 0.396,0.323 0.313,0.198 10 *a 1.146,0.292 1.458,0.49 0.313,0.198 10 RB
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B36-1 (RB) - Body ground Ignition switch ON 11 to 14 V
B36-1 (RB) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TCM OUTPUT SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (PARK/NEUTRAL POSITION SWITCH - BATTERY)

2.CHECK HARNESS AND CONNECTOR (TCM OUTPUT SIGNAL)
a.

Disconnect the B76 ECM connector.


b.
C197711
0.25,0.885 0.688,1.146 0.438,0.26 2.094,1.01 2.26,0.458 true 0.354,0.927 0.729,1.156 0.375,0.229 10 B36 0.135,0.146 0.448,0.344 0.313,0.198 10 *a 2.333,0.323 2.646,0.521 0.313,0.198 10 B
*a Front view of wire harness connector
(to Park/Neutral Position Switch Assembly)


Disconnect the park/neutral position switch connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
B36-4 (B) - Body ground Ignition switch ON 11 to 14 V
B36-4 (B) - Body ground Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
3.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.
C197712C20
1.833,0.938 2.229,0.385 true 1.604,0.927 1.729,0.375 true 1.281,0.958 0.99,0.458 true 1.052,1.625 1.344,1.292 true 2.052,1.615 1.698,1.302 true 0.083,0.094 0.396,0.292 0.313,0.198 10 *a 2.271,0.26 2.583,0.458 0.313,0.198 10 RB 2.125,1.583 2.365,1.781 0.24,0.198 10 DL 0.854,0.344 1.094,0.542 0.24,0.198 10 B 0.938,1.583 1.177,1.781 0.24,0.198 10 L 1.771,0.26 2.01,0.458 0.24,0.198 10 RL
*a Component without harness connected
(Park/Neutral Position Switch)


Disconnect the park/neutral position switch connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
4 (B) - 9 (L) Shift lever in P Below 1 Ω
1 (RB) - 2 (RL) Shift lever in R Below 1 Ω
4 (B) - 9 (L) Shift lever in N Below 1 Ω
1 (RB) - 7 (DL) Shift lever in D, M, "+"or "-" Below 1 Ω
4 (B) - 9 (L) Shift lever not in P 10 kΩ or higher
1 (RB) - 2 (RL) Shift lever not in R 10 kΩ or higher
4 (B) - 9 (L) Shift lever not in N 10 kΩ or higher
1 (RB) - 7 (DL) Shift lever not in D, M,"+" or "-" 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)

NG

4.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
a.
C205632
1.51,0.156 1.948,0.417 0.438,0.26 1.781,1.771 2.042,1.208 true 2.427,1.781 2.156,1.219 true 0.156,0.135 0.469,0.333 0.313,0.198 10 *a 1.583,0.198 1.958,0.427 0.375,0.229 10 B79 2.292,1.833 2.76,2.031 0.469,0.198 10 16 (D) 1.552,1.823 2.021,2.021 0.469,0.198 10 15 (R)
*a Front view of wire harness connector
(to TCM)


Disconnect the TCM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
B79-16 (D) - Body ground
·

Ignition switch ON

·

Shift lever in D


11 to 14 V
B79-15 (R) - Body ground
·

Ignition switch ON

·

Shift lever in R


11 to 14 V*
B79-16 (D) - Body ground
·

Ignition switch ON

·

Shift lever not in D


Below 1 V
B79-15 (R) - Body ground
·

Ignition switch ON

·

Shift lever not in R


Below 1 V


HINT:

*: The voltage will drop slightly due to the illumination of the back-up light.



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - TCM)
a.

Disconnect the B36 park/neutral position switch connector.


b.

Disconnect the B79 TCM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B36-4 (B) - B79-11 (NSW) Always Below 1 Ω
B36-4 (B) or B79-11 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR