Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › BLIND SPOT MONITOR SYSTEM › 2012.12–2015.10
RM3090E _56 Audio / Visual / Telematics _008432 PARK ASSIST / MONITORING _0047058 BLIND SPOT MONITOR SYSTEM J

PARK ASSIST / MONITORING  BLIND SPOT MONITOR SYSTEM  Main Switch Circuit  


DESCRIPTION

When the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) is turned on, a signal is sent to the blind spot monitor sensor LH and the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) illuminates. The blind spot monitor system operates according to this signal.

*1: for LHD

*2: for RHD


WIRING DIAGRAM

E270268E01
0.073,4.208 1.031,4.427 0.958,0.219 10 *1: for LHD 0.083,4.49 1,4.719 0.917,0.229 10 *2: for RHD 2.24,1.177 2.865,1.385 0.625,0.208 10 GAUGE 5.667,3.865 6.823,4.26 1.156,0.396 10 Blind Spot Monitor Sensor LH 5.656,3.677 5.969,3.875 0.313,0.198 10 R1 0.313,0.969 1.76,1.271 1.448,0.302 10 from IG1 NO. 2 Relay 5.813,0.833 6.427,1.031 0.615,0.198 10 BIND 5.615,0.729 5.771,0.927 0.156,0.198 10 3 5.813,1.125 6.427,1.323 0.615,0.198 10 BSSW 5.615,1.031 5.771,1.229 0.156,0.198 10 8 4.344,0.854 4.5,1.052 0.156,0.198 10 E 4.354,1.135 4.51,1.333 0.156,0.198 10 D 4.375,2.896 4.531,3.094 0.156,0.198 10 D 4.375,2.615 4.531,2.813 0.156,0.198 10 E 2.854,1.635 5.146,2.083 2.292,0.448 10 Blind Spot Monitor Main Switch (Warning Cancel Switch Assembly)*1 2.875,1.448 3.208,1.677 0.333,0.229 10 G75 3.094,3.479 5.01,3.854 1.917,0.375 10 Blind Spot Monitor Main Switch (Telltale Light Assembly)*2 3.094,3.271 3.552,3.469 0.458,0.198 10 G43 4.531,0.74 4.844,0.938 0.313,0.198 10 12 4.552,1.052 4.708,1.25 0.156,0.198 10 8 4.563,2.802 4.719,3 0.156,0.198 10 8 4.542,2.5 4.854,2.698 0.313,0.198 10 10 3.313,0.854 3.625,1.052 0.313,0.198 10 11 3.573,0.958 4.031,1.156 0.458,0.198 10 B 2.104,2.969 2.979,3.198 0.875,0.229 10 ECU-B NO. 1 0.844,2.74 1.656,3.021 0.813,0.281 10 from Battery 3.594,2.74 3.75,2.938 0.156,0.198 10 B 3.323,2.625 3.635,2.823 0.313,0.198 10 16

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Proceed to
for LHD
for RHD



for LHD

2.CHECK BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)

for RHD

9.CHECK BLIND SPOT MONITOR MAIN SWITCH (TELLTALE LIGHT ASSEMBLY)
2.CHECK BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)
a.

Check that the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly) illuminates normally when the blind spot monitor main switch (warning cancel switch assembly) is turned from off to on.


b.

Check that the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly) turns off normally when the blind spot monitor main switch (warning cancel switch assembly) is turned from on to off.


Result:
Proceed to
The blind spot monitor indicator operates normally
The blind spot monitor indicator does not operate normally



The blind spot monitor indicator operates normally

3.READ VALUE USING GTS

The blind spot monitor indicator does not operate normally

7.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)
3.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Blind spot monitor Master / Data List.


e.

According to the display on GTS, read the Data List.

Body Electrical > Blind Spot Monitor Master > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch Blind spot monitor main switch (warning cancel switch assembly) OFF or ON ON: Blind spot monitor main switch (warning cancel switch assembly) on
OFF: Blind spot monitor main switch (warning cancel switch assembly) off
-
Body Electrical > Blind Spot Monitor Master > Data List
Tester Display
Main Switch
50003 313 2
Result:
Result Proceed to
The display does not change as shown above when the blind spot monitor main switch (warning cancel switch assembly) is operated. A
The display changes as shown above when the blind spot monitor main switch (warning cancel switch assembly) is operated. B




A

4.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

4.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)
a.

Remove the blind spot monitor main switch (warning cancel switch assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH(for LHD)>REMOVAL


b.

Inspect the blind spot monitor main switch (warning cancel switch assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH(for LHD)>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)

NG

REPLACE BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)
a.

Disconnect the G75 blind spot monitor main switch (warning cancel switch assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G75-11 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the R1 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-8 (BSSW) - G75-8 (D) Always Below 1 Ω
R1-8 (BSSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)
a.

Remove the blind spot monitor main switch (warning cancel switch assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH(for LHD)>REMOVAL


b.

Inspect the blind spot monitor main switch (warning cancel switch assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH(for LHD)>INSPECTION


Result:
Proceed to
OK
NG



OK

8.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)

NG

REPLACE BLIND SPOT MONITOR MAIN SWITCH (WARNING CANCEL SWITCH ASSEMBLY)

8.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the R1 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-3 (BIND) - G75-12 (E) Always Below 1 Ω
R1-3 (BIND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK BLIND SPOT MONITOR MAIN SWITCH (TELLTALE LIGHT ASSEMBLY)
a.

Check that the blind spot monitor indicator on the blind spot monitor main switch (telltale light assembly) illuminates normally when the blind spot monitor main switch (telltale light assembly) is turned from off to on.


b.

Check that the blind spot monitor indicator on the blind spot monitor main switch (telltale light assembly) turns off normally when the blind spot monitor main switch (telltale light assembly) is turned from on to off.


Result:
Proceed to
The blind spot monitor indicator operates normally
The blind spot monitor indicator does not operate normally



The blind spot monitor indicator operates normally

10.READ VALUE USING GTS

The blind spot monitor indicator does not operate normally

14.INSPECT BLIND SPOT MONITOR MAIN SWITCH (TELLTALE LIGHT ASSEMBLY)
10.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS ON.


d.

Enter the following menus: Body Electrical / Blind spot monitor Master / Data List.


e.

According to the display on GTS, read the Data List.

Body Electrical > Blind Spot Monitor Master > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Main Switch Blind spot monitor main switch (telltale light assembly) OFF or ON ON: Blind spot monitor main switch (telltale light assembly) on
OFF: Blind spot monitor main switch (telltale light assembly) off
-
Body Electrical > Blind Spot Monitor Master > Data List
Tester Display
Main Switch
50003 313 2
Result:
Result Proceed to
The display does not change as shown above when the blind spot monitor main switch (telltale light assembly) is operated. A
The display changes as shown above when the blind spot monitor main switch (telltale light assembly) is operated. B




A

11.INSPECT BLIND SPOT MONITOR MAIN SWITCH (TELLTALE LIGHT ASSEMBLY)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

11.INSPECT BLIND SPOT MONITOR MAIN SWITCH (TELLTALE LIGHT ASSEMBLY)
a.

Remove the blind spot monitor main switch (telltale light assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH(for LHD)>REMOVAL


b.

Inspect the blind spot monitor main switch (telltale light assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH(for LHD)>INSPECTION


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)

NG

REPLACE BLIND SPOT MONITOR MAIN SWITCH (TELLTALE LIGHT SWITCH ASSEMBLY)

12.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BATTERY)
a.

Disconnect the G43 blind spot monitor main switch (telltale light assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G43-16 (B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the G43 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-8 (BSSW) - G43-8 (D) Always Below 1 Ω
R1-8 (BSSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.INSPECT BLIND SPOT MONITOR MAIN SWITCH (TELLTALE LIGHT ASSEMBLY)
a.

Remove the blind spot monitor main switch (telltale light assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH(for RHD)>REMOVAL


b.

Inspect the blind spot monitor main switch (telltale light assembly).

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR MAIN SWITCH(for RHD)>INSPECTION


Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)

NG

REPLACE BLIND SPOT MONITOR MAIN SWITCH (TELLTALE LIGHT ASSEMBLY)

15.CHECK HARNESS AND CONNECTOR (BLIND SPOT MONITOR MAIN SWITCH - BLIND SPOT MONITOR SENSOR LH)
a.

Disconnect the R1 blind spot monitor sensor LH connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R1-3 (BIND) - G43-10 (E) Always Below 1 Ω
R1-3 (BIND) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR