Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2012.12–2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0048454 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Engine Stop and Start ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Engine Stop and Start ECU Communication Stop Mode Either condition is met:
·

"Stop and Go/Start" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Engine Stop and Start ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside engine stop and start ECU

·

Engine stop and start ECU CAN branch wire or connector

·

Engine stop and start ECU



For vehicles with a stop and start system.


WIRING DIAGRAM

C277466E02
5.167,7.167 6.917,7.365 1.75,0.198 10 false Engine Stop and Start ECU 5.667,6.219 6.083,6.417 0.417,0.198 10 false GND 5.667,5.5 6.083,5.698 0.417,0.198 10 false ACC 5.667,4.802 6.083,5 0.417,0.198 10 false IG2 5.667,4.052 6.083,4.25 0.417,0.198 10 false IG1 5.667,3.302 6.083,3.5 0.417,0.198 10 false BIN 5.667,2.583 6.083,2.781 0.417,0.198 10 false +B 5.667,1.385 6.083,1.583 0.417,0.198 10 false CANL 5.667,0.833 6.167,1 0.5,0.167 10 false CANH 5.167,6.219 5.583,6.417 0.417,0.198 10 false A65 5.167,5.5 5.583,5.698 0.417,0.198 10 false G87 5.167,3.302 5.583,3.5 0.417,0.198 10 false A65 5.167,2.583 5.583,2.781 0.417,0.198 10 false A65 5.167,4.781 5.583,4.979 0.417,0.198 10 false G87 5.167,4.052 5.583,4.25 0.417,0.198 10 false G87 5.167,1.417 5.583,1.615 0.417,0.198 10 false G87 5.167,0.823 5.583,1.021 0.417,0.198 10 false G87 1.667,0.667 2.083,0.865 0.417,0.198 10 false 1 1.667,1.302 2.083,1.5 0.417,0.198 10 false 2 0.417,1.75 0.833,1.948 0.417,0.198 10 false G154 0.417,1.917 3.083,2.167 2.667,0.25 10 false No. 2 CAN Junction Connector 5.229,2.333 5.646,2.531 0.417,0.198 10 false 5 5.198,1.167 5.615,1.365 0.417,0.198 10 false 16 5.198,0.583 5.615,0.781 0.417,0.198 10 false 15 5.229,3.052 5.646,3.25 0.417,0.198 10 false 7 5.198,3.813 5.615,4.01 0.417,0.198 10 false 17 5.198,4.5 5.615,4.698 0.417,0.198 10 false 20 5.188,5.219 5.604,5.417 0.417,0.198 10 false 19 5.219,5.938 5.635,6.135 0.417,0.198 10 false 8 1.333,2.583 3.167,2.833 1.833,0.25 10 false from EFI-MAIN NO.2 Relay 2.25,3.302 3.167,3.552 0.917,0.25 10 false from Battery 1.75,4.052 3.083,4.25 1.333,0.198 10 false from IG1 NO.1 Relay 2.042,4.771 3.125,5 1.083,0.229 10 false from IG2 Relay 2.031,5.5 3.115,5.729 1.083,0.229 10 false from ACC Relay 4.167,5.333 5.25,5.563 1.083,0.229 10 false ACC 4.167,4.583 5.25,4.813 1.083,0.229 10 false IGN 4.073,3.917 5.156,4.146 1.083,0.229 10 false EPS-IG 4.167,3.167 5.25,3.396 1.083,0.229 10 false BBC

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ENGINE STOP AND START ECU CAN BRANCH WIRE)
a.
C251435C06
0.313,0.927 0.677,1.156 0.365,0.229 2.646,1.5 2.406,1.5 2.406,1.5 2.146,1.188 true 2.573,1.698 2.333,1.698 2.333,1.698 2.073,1.198 true 0.354,0.969 0.813,1.167 0.458,0.198 10 G87 0.073,0.094 0.531,0.292 0.458,0.198 10 *a 2.677,1.417 3.135,1.615 0.458,0.198 10 CANH 2.615,1.625 3.073,1.823 0.458,0.198 10 CANL
*a Rear view of wire harness connector
(to Engine Stop and Start ECU)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the engine stop and start ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-15 (CANH) - G87-16 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE ENGINE STOP AND START ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BATTERY AND BODY GROUND)
a.
C277467C01
0.333,2.25 0.75,2.5 0.417,0.25 0.417,0.667 0.833,0.917 0.417,0.25 2.531,2.844 2.313,2.844 2.313,2.844 2.01,2.521 true 2.354,1.281 2.146,1.281 2.146,1.281 1.865,0.938 true 2.583,0.802 2.365,0.802 2.365,0.802 2.135,0.938 true 1.156,1.396 1.375,1.396 1.375,1.396 1.583,0.958 true 1.167,2.948 1.385,2.948 1.385,2.948 1.594,2.51 true 2.354,3.135 2.073,3.135 2.073,3.135 1.854,2.521 true 0.167,0.094 0.479,0.25 0.313,0.156 10 *a 0.49,0.719 0.802,0.875 0.313,0.156 10 A65 0.417,2.302 0.729,2.458 0.313,0.156 10 G87 2.396,1.198 2.708,1.354 0.313,0.156 10 BIN 2.635,0.729 2.948,0.885 0.313,0.156 10 +B 0.823,1.323 1.208,1.49 0.385,0.167 10 GND 2.573,2.781 2.885,2.938 0.313,0.156 10 IG1 0.875,2.885 1.188,3.042 0.313,0.156 10 IG2 2.406,3.063 2.802,3.219 0.396,0.156 10 ACC
*a Rear view of wire harness connector
(to Engine Stop and Start ECU)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the engine stop and start ECU connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A65-7 (BIN) - Body ground Always 11 to 14 V
A65-5 (+B) - Body ground Ignition switch ON 11 to 14 V
G87-17 (IG1) - Body ground Ignition switch ON 11 to 14 V
G87-20 (IG2) - Body ground Ignition switch ON 11 to 14 V
G87-19 (ACC) - Body ground Ignition switch ACC 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A65-8 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR