Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2012.12–2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0048454 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  4WD Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Detection Item Trouble Area
4WD Control ECU Communication Stop Mode Either condition is met:
·

"Four Wheel Drive Control" is not displayed on the "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "4WD Control ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of 4WD ECU assembly

·

4WD ECU assembly CAN branch wire or connector

·

4WD ECU assembly



For vehicles with a 4WD/AWD.


WIRING DIAGRAM

C277463E02
5.438,3.917 7.01,4.25 1.573,0.333 10 G86 5.448,4.094 6.802,4.417 1.354,0.323 10 4WD ECU Assembly 5.667,3.292 6.833,3.458 1.167,0.167 10 GND 5.667,2.458 6.833,2.625 1.167,0.167 10 IG1 5.656,0.958 6.823,1.125 1.167,0.167 10 CANH 5.667,1.552 6.833,1.719 1.167,0.167 10 CANL 5.417,1.417 6.583,1.583 1.167,0.167 10 5 5.417,0.844 6.583,1.01 1.167,0.167 10 6 5.438,2.333 6.604,2.5 1.167,0.167 10 3 5.458,3.156 6.625,3.323 1.167,0.167 10 4 1.688,0.875 2.854,1.042 1.167,0.167 10 1 1.708,1.438 2.875,1.604 1.167,0.167 10 2 0.323,1.896 1.49,2.063 1.167,0.167 10 G131 0.333,2.083 2.833,2.25 2.5,0.167 10 No. 2 CAN Junction Connector 1.781,2.427 4.281,2.615 2.5,0.188 10 from IG1 NO.1 Relay 3.938,2.271 4.906,2.458 0.969,0.188 10 ECU-IG NO.1

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Drive the vehicles for 4.5 seconds or more at a speed 60 km/h (37 mph) or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (4WD ECU ASSEMBLY CAN BRANCH WIRE)
a.
C251077C03
0.333,0.958 0.75,1.25 0.417,0.292 2.583,1.5 2.417,1.5 2.417,1.5 2.24,1.24 true 2.51,1.75 2.344,1.75 2.344,1.75 2.177,1.25 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 0.396,1.021 0.854,1.219 0.458,0.198 10 G86 2.625,1.406 3.083,1.604 0.458,0.198 10 CANL 2.563,1.656 3.021,1.854 0.458,0.198 10 CANH
*a Rear view of wire harness connector
(to 4WD ECU Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the 4WD ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G86-6 (CANH) - G86-5 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE 4WD ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (4WD ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C251077C04
2.563,0.948 2.979,1.24 0.417,0.292 1.344,1.052 1.083,0.583 1.083,0.583 0.833,0.583 true 0.75,0.833 0.917,0.833 0.917,0.833 1.219,1.063 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 2.625,1 3.083,1.198 0.458,0.198 10 G86 0.594,0.521 1.052,0.719 0.458,0.198 10 IG1 0.417,0.771 0.875,0.969 0.458,0.198 10 GND
*a Rear view of wire harness connector
(to 4WD ECU Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G86-3 (IG1) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G86-4 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR