Home › Drivetrain › EA64 MANUAL TRANSMISSION / TRANSAXLE › OUTPUT SHAFT
RM3090E _52 Drivetrain _008755 EA64 MANUAL TRANSMISSION / TRANSAXLE _0048557 OUTPUT SHAFT A

EA64 MANUAL TRANSMISSION / TRANSAXLE  OUTPUT SHAFT  DISASSEMBLY  


PROCEDURE

Hide 33335 1.INSPECT 1ST DRIVEN GEAR THRUST CLEARANCE

Hide 33335 2.INSPECT 1ST DRIVEN GEAR RADIAL CLEARANCE

Hide 33332 3.INSPECT 2ND DRIVEN GEAR THRUST CLEARANCE

Hide 33332 4.INSPECT 2ND DRIVEN GEAR RADIAL CLEARANCE

Hide 33423A 5.INSPECT 3RD DRIVEN GEAR THRUST CLEARANCE

Hide 33423A 6.INSPECT 3RD DRIVEN GEAR RADIAL CLEARANCE

Hide 33422B 7.INSPECT 4TH DRIVEN GEAR THRUST CLEARANCE

Hide 33422B 8.INSPECT 4TH DRIVEN GEAR RADIAL CLEARANCE

Hide 33321B 9.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C112408

Using a snap ring expander, remove the output shaft bearing shaft snap ring from the No. 1 output shaft.


Hide 33321A 10.REMOVE REAR OUTPUT SHAFT BEARING

a.
C112409E01
1.424,0.136 1.754,0.48 0.33,0.344 10 SST 0.918,0.695 1.39,0.223 1.39,0.223 1.175,0.976 false

Using SST and press, press out the rear output shaft bearing from the No. 1 output shaft.

SST
09201-31010  
09950-00020  


Hide 33423A 11.REMOVE 3RD DRIVEN GEAR

a.
C112410

Remove the 3rd driven gear from the No. 1 output shaft.


Hide 12.REMOVE SPACER

a.
C112411

Remove the spacer from the No. 1 output shaft.


Hide 33334A 13.REMOVE NEEDLE ROLLER BEARING

a.
C112412

Remove the needle roller bearing from the No. 1 output shaft.


Hide 33047 14.REMOVE 3RD DRIVEN GEAR SYNCHRONIZER RING SET

a.
C112413

Remove the 3rd driven gear synchronizer ring set from the No. 1 output shaft.


Hide 33352C 15.REMOVE SHAFT SNAP RING

a.
C112414

Using 2 screwdrivers and a hammer, tap out the shaft snap ring from the No. 1 output shaft.

NOTICE:

Use a piece of cloth to prevent the snap ring from flying off.



Hide 33422B 16.REMOVE 4TH DRIVEN GEAR

a.
C133415E01
0.547,0.239 0.851,0.4 0.304,0.161 10 SST 0.484,0.354 0.35,0.351 false 0.35,0.351 0.35,1.071 false

Using SST and press, press out the No. 2 transmission hub sleeve, 4th driven gear synchronizer ring set and 4th driven gear from the No. 1 output shaft.

SST
09950-00020  


Hide 33047 17.REMOVE 4TH DRIVEN GEAR SYNCHRONIZER RING SET

a.
C117924

Remove the 4th driven gear synchronizer ring set from the 4th driven gear.


Hide 33362 18.REMOVE NO. 2 TRANSMISSION CLUTCH HUB

a.
C277781

Remove the No. 2 transmission clutch hub, 3 No. 1 synchromesh shifting keys, 3 balls and 3 synchromesh shifting key springs from the No. 2 transmission hub sleeve.

NOTICE:

Pay attention to prevent the balls and 3 synchromesh shifting key springs from scattering.



Hide 33334A 19.REMOVE NEEDLE ROLLER BEARING

a.
C112416

Remove the 2 pieces of the needle roller bearing from the No. 1 output shaft.


Hide 33334B 20.REMOVE SPACER

a.
C112417

Remove the spacer from the No. 1 output shaft.


Hide 33321B 21.REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C112418

Using a snap ring expander, remove the output shaft bearing shaft snap ring from the No. 1 output shaft.


Hide 33356A 22.REMOVE INNER 2ND GEAR BEARING RACE

a.
C112419

Remove the inner 2nd gear bearing race from the No. 1 output shaft.


Hide 33332 23.REMOVE 2ND DRIVEN GEAR

a.
C112420

Remove the 2nd driven gear from the No. 1 output shaft.


Hide 33332B 24.REMOVE NEEDLE ROLLER BEARING

a.
C112421

Remove the needle roller bearing from the No. 1 output shaft.


Hide 33365C 25.REMOVE SYNCHROMESH SHIFTING KEY BALL

a.
C116562

Using a magnet hand, remove the synchromesh shifting key ball from the No. 1 output shaft.


Hide 26.REMOVE 2ND DRIVEN GEAR SYNCHRONIZER RING SET

a.
C112422

Remove the 2nd driven gear synchronizer ring set from the No. 1 output shaft.


Hide 33335 27.REMOVE 1ST DRIVEN GEAR

a.
C278089N01
1.385,1.104 1.271,0.26 1.271,0.26 1.479,0.26 false 1.531,0.156 1.99,0.354 0.458,0.198 10 SST

Using SST and a press, press out the No. 1 transmission hub sleeve, 1st driven gear synchronizer ring set and 1st driven gear from the No. 1 output shaft.

SST
09950-00020  


Hide 33037B 28.REMOVE 1ST DRIVEN GEAR SYNCHRONIZER RING SET

a.
C117926

Remove the 1st driven gear synchronizer ring set from the 1st driven gear.


Hide 33361 29.REMOVE NO. 1 TRANSMISSION CLUTCH HUB

a.
C117927

Remove the No. 1 transmission clutch hub, 3 No. 1 synchromesh shifting keys, 3 balls and 3 synchromesh shifting key springs from the No. 1 transmission hub sleeve.

NOTICE:

Pay attention to prevent the balls and 3 synchromesh shifting key springs from scattering.



Hide 33335C 30.REMOVE NEEDLE ROLLER BEARING

a.
C112425

Remove the needle roller bearing from the No. 1 output shaft.


Hide 33321Y 31.REMOVE FRONT OUTPUT SHAFT BEARING SHAFT SNAP RING

a.
C112426

Using a snap ring expander, remove the front output shaft bearing shaft snap ring from the No. 1 output shaft.


Hide 33321N 32.REMOVE FRONT OUTPUT SHAFT BEARING

a.
C112427E01
0.209,0.408 0.514,0.759 0.304,0.351 10 SST 0.834,1.031 0.565,0.483 0.565,0.483 1.034,0.569 false

Using SST and press, press out the front output shaft bearing from the No. 1 output shaft.

SST
09201-31010  
09950-00020  


Hide 33.INSPECT 5TH DRIVEN GEAR THRUST CLEARANCE

Hide 34.INSPECT 5TH DRIVEN GEAR RADIAL CLEARANCE

Hide 35.INSPECT 6TH DRIVEN GEAR THRUST CLEARANCE

Hide 36.INSPECT 6TH DRIVEN GEAR RADIAL CLEARANCE

Hide 37.INSPECT REVERSE DRIVEN GEAR THRUST CLEARANCE

Hide 38.INSPECT REVERSE DRIVEN GEAR RADIAL CLEARANCE

Hide 33322C 39.REMOVE NO. 2 OUTPUT SHAFT BEARING SNAP RING

a.
C112395

Using a snap ring expander, remove the No. 2 output shaft bearing snap ring from the No. 2 output shaft.


Hide 33322A 40.REMOVE REAR NO. 2 OUTPUT SHAFT BEARING

a.
C112396E01
0.02,0.316 0.352,0.649 0.332,0.332 10 SST 0.594,1.11 0.41,0.42 0.41,0.42 0.741,0.637 false

Using SST and press, press out the rear No. 2 output shaft bearing and 6th driven gear from the No. 2 output shaft.

SST
09201-31010  
09950-00020  


Hide 41.REMOVE NEEDLE ROLLER BEARING

a.
C116204

Remove the 2 pieces of the needle roller bearing from the No. 2 output shaft.


Hide 42.REMOVE SPACER

a.
C116203

Remove the spacer from the No. 2 output shaft.


Hide 33394 43.REMOVE 6TH GEAR SYNCHRONIZER RING

a.
C116202

Remove the 6th gear synchronizer ring from the No. 2 output shaft.


Hide 33352C 44.REMOVE SHAFT SNAP RING

a.
C112397

Using 2 screwdrivers and a hammer, tap out the shaft snap ring from the No. 2 output shaft.

NOTICE:

Use a piece of cloth to prevent the snap ring from flying off.



Hide 33428C 45.REMOVE 5TH DRIVEN GEAR

a.
C112398E01
1.424,0.21 1.746,0.554 0.322,0.344 10 SST 1.283,1.07 1.283,0.288 1.283,0.288 1.39,0.288 false

Using SST and a press, press out the No. 3 transmission hub sleeve, 5th driven gear synchronizer ring and 5th driven gear from the No. 2 output shaft.

SST
09950-00020  


Hide 33368J 46.REMOVE 5TH DRIVEN GEAR SYNCHRONIZER RING

a.
C117928

Remove the 5th driven gear synchronizer ring from the 5th driven gear.


Hide 33393 47.REMOVE NO. 3 TRANSMISSION CLUTCH HUB

a.
C117929

Remove the No. 3 transmission clutch hub, 3 No. 1 synchromesh shifting keys, 3 balls and 3 synchromesh shifting key springs from the No. 3 transmission hub sleeve.

NOTICE:

Pay attention to prevent the balls and 3 synchromesh shifting key springs from scattering.



Hide 33322D 48.REMOVE OUTPUT SHAFT COLLAR

a.
C112400

Remove the output shaft collar from the No. 2 output shaft.


Hide 33336A 49.REMOVE 5TH GEAR NEEDLE ROLLER BEARING

a.
C112401

Remove the 2 pieces of the 5th gear needle roller bearing from the No. 2 output shaft.


Hide 33336B 50.REMOVE 5TH GEAR BEARING SPACER

a.
C112402

Remove the 5th gear bearing spacer from the No. 2 output shaft.


Hide 33352C 51.REMOVE SHAFT SNAP RING

a.
C112403

Using 2 screwdrivers and a hammer, remove the shaft snap ring from the No. 2 output shaft.

NOTICE:

Use a piece of cloth to prevent the snap ring from flying off.



Hide 33331 52.REMOVE REVERSE DRIVEN GEAR

a.
C112404E01
0.072,0.314 0.374,0.653 0.302,0.339 10 SST 0.45,0.385 0.628,0.385 0.628,0.385 0.628,1.187 false

Using SST and press, press out the No. 4 transmission hub sleeve, reverse driven gear synchronizer ring set and reverse driven gear from the No. 2 output shaft.

SST
09950-00020  


Hide 53.REMOVE REVERSE DRIVEN GEAR SYNCHRONIZER RING

a.
C117930

Remove the reverse driven gear synchronizer ring from the reverse driven gear.


Hide 33352B 54.REMOVE NO. 4 TRANSMISSION CLUTCH HUB

a.
C117931C04
2.188,1.979 2.479,1.979 2.479,1.979 2.479,1.698 false 1.354,1.896 1.354,1.417 false 2.094,0.906 2.292,0.51 2.292,0.51 2.542,0.51 false 0.604,1.656 0.604,1.25 false 1.979,1.906 2.167,2.104 0.188,0.198 10 false *1 1.292,1.938 1.604,2.135 0.313,0.198 10 false *2 0.531,1.719 0.844,1.917 0.313,0.198 10 false *4 2.604,0.448 2.917,0.646 0.313,0.198 10 false *3
*1 No. 4 Transmission Clutch Hub
*2 Shifting Key
*3 Key Spring
*4 No. 4 Transmission Hub Sleeve


Remove the No. 4 transmission clutch hub, shifting key and key spring from the No. 4 transmission hub sleeve.


Hide 55.REMOVE NEEDLE ROLLER BEARING

a.
C112406

Remove the needle roller bearing from the No. 2 output shaft.


Hide 33322B 56.REMOVE NO. 2 OUTPUT SHAFT FRONT BEARING

a.
C112407E01
0.06,0.488 0.361,0.807 0.3,0.318 10 SST 0.752,1.111 0.41,0.586 0.41,0.586 1.058,0.723 false

Using SST and press, press out the No. 2 output shaft front bearing from the No. 2 output shaft.

SST
09201-31010  
09950-00020