Home › Drivetrain › EB61F MANUAL TRANSMISSION / TRANSAXLE › MANUAL TRANSAXLE UNIT › 2012.12–2015.10
RM3090E _52 Drivetrain _008758 EB61F MANUAL TRANSMISSION / TRANSAXLE _0048573 MANUAL TRANSAXLE UNIT A

EB61F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 41311E 1.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING

a.
C204252N02
0.561,1.795 0.873,1.939 0.313,0.145 10 SST 0.935,1.875 1.263,1.875 false 1.314,2.243 1.096,2.243 false 1.096,2.243 1.096,1.875 false

Using SST and a press, press a new front differential case front tapered roller bearing onto the differential case assembly.

SST
09316-20011  
09513-36040  


b.

Install the front differential oil baffle into the front transaxle case.


c.
C200156N02
0.366,2.049 0.661,2.205 0.295,0.156 10 SST 0.383,0.806 0.231,0.806 false 0.231,0.659 0.231,2.138 false 0.228,2.138 0.319,2.138 false 0.473,0.969 0.231,0.969 false 0.693,0.66 0.231,0.66 false 3.02,0.903 3.315,1.059 0.295,0.156 10 SST 2.994,0.979 2.792,0.979 false 2.792,0.979 2.581,1.326 false

Using SST and a press, press the front differential case front tapered roller bearing (outer race) into the front transaxle case.

SST
09950-60010  (09952-06010)
09950-60020  (09951-00770, 09951-00910)
09950-70010  (09951-07100)


Hide 41311F 2.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING

a.
C200157N01
0.823,0.624 1.111,0.766 0.288,0.142 10 SST 1.21,0.714 1.957,0.714 false 1.957,0.714 2.331,1.522 false 1.442,0.714 1.874,1.653 false 1.803,0.714 2.217,1.613 false 0.144,2.497 0.432,2.64 0.288,0.142 10 SST 0.535,2.583 0.939,2.583 false 0.948,2.993 0.807,2.993 false 0.807,2.993 0.807,2.583 false

Using SST and a press, press a new front differential case rear tapered roller bearing onto the differential case assembly.

SST
09316-20011  
09950-40011  (09957-04010)
09950-60020  (09951-00910)
09950-60010  (09951-00580, 09952-06010)
09950-70010  (09951-07100)


b.
C200158N01
2.094,0.469 1.229,0.469 false 2.135,0.938 1.51,0.938 false 1.51,0.938 1.51,0.469 false 0.823,0.385 1.146,0.563 0.323,0.177 10 SST

Using SST, install the front differential case rear tapered roller bearing (outer race) together with the front differential case rear shim as shown in the illustration.

SST
09950-60020  (09951-00770, 09951-00890)


Hide 33321N 3.INSTALL FRONT OUTPUT SHAFT BEARING

a.
C202188

Install the output shaft cover to the front transaxle case.

NOTICE:

Insert the output shaft cover key into the case groove.



b.
C200161N02
0.23,0.453 0.521,0.607 0.291,0.154 10 SST 0.966,1.002 0.966,0.538 false 0.966,0.538 0.592,0.538 false 0.902,1.074 0.902,0.538 false 3.008,1.124 3.3,1.278 0.291,0.154 10 SST 2.099,2.136 2.738,1.208 false 2.117,1.937 2.619,1.205 false 2.613,1.207 2.964,1.207 false

Using SST and a press, press the front output shaft bearing (outer race) into the front transaxle case.

SST
09950-60010  (09951-00620, 09952-06010)
09950-60020  (09951-00710)
09950-70010  (09951-07100)


Hide 33321A 4.INSTALL REAR OUTPUT SHAFT BEARING

a.
C200162N02
2.083,0.771 2.51,0.771 false 2.51,0.771 2.51,1.052 false 2.417,1.146 2.417,0.771 false 1.198,2.177 1.75,2.729 false 1.063,2.354 1.469,2.74 1.469,2.74 2.615,2.74 false 1.698,0.688 2,0.833 0.302,0.146 10 SST 2.698,2.667 3.052,2.854 0.354,0.188 10 SST

Using SST and a press, press the rear output shaft bearing (outer race) together with the rear output shaft bearing shim into the manual transmission case.

SST
09950-60010  (09951-00490, 09951-00620, 09952-06010)
09950-70010  (09951-07150)


Hide 5.INSTALL STRAIGHT PIN

a.
C202190C01
2.177,2.646 2.771,2.646 false 2.802,2.583 3.021,2.781 0.219,0.198 10 *a
*a Protrusion


Using a plastic-faced hammer, tap in 5 new straight pins to the specified protrusion height.

Protrusion height:

10.5 to 11.5 mm (0.414 to 0.452 in.)



Hide 6.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.
C202182

Coat the differential case assembly with gear oil and install it to the front transaxle case.


b.
C199075

Install the manual transmission case with the 17 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


c.
C200159N02
2.171,0.173 2.493,0.322 0.323,0.149 10 SST 0.934,1.074 1.688,0.257 false 1.688,0.257 2.112,0.257 false

Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

SST
09564-50010  


d.

Using SST and a torque wrench, measure the preload.

SST
09564-50010  

Standard preload (at starting):
New bearing:

1.50 to 2.30 N*m (15 to 23 kgf*cm, 13 to 20 in.*lbf)

Used bearing:

0.24 to 0.37 N*m (2.44 to 3.77 kgf*cm, 2.12 to 3.27 in.*lbf)


If the preload is not as specified, replace the front differential case rear shim with another one of a different thickness. Use the table below to select a front differential case rear shim which will ensure that the preload is within the specification.

Standard Shim Thickness:
Mark Specified Condition Mark Specified Condition
A 2.05 mm (0.0807 in.) K 2.50 mm (0.0984 in.)
B 2.10 mm (0.0827 in.) L 2.55 mm (0.100 in.)
C 2.15 mm (0.0846 in.) M 2.60 mm (0.102 in.)
D 2.20 mm (0.0866 in.) N 2.65 mm (0.104 in.)
E 2.25 mm (0.0886 in.) P 2.70 mm (0.106 in.)
F 2.30 mm (0.0906 in.) Q 2.75 mm (0.108 in.)
G 2.35 mm (0.0925 in.) R 2.80 mm (0.110 in.)
H 2.40 mm (0.0945 in.) S 2.85 mm (0.112 in.)
J 2.45 mm (0.0965 in.) T 2.90 mm (0.114 in.)


HINT:
·

Select a thicker front differential case rear shim to increase the preload, or a thinner front differential case rear shim to decrease the preload.

·

Make a memo as the torque values will be needed for the Adjust Output Shaft Bearing Preload procedure.




e.

Remove the 17 bolts and manual transmission case.


f.

Remove the differential case assembly from the front transaxle case.


g.

Replace the installed front differential case rear shim with the one selected above.


Hide 7.ADJUST OUTPUT SHAFT BEARING PRELOAD

a.
C202182

Coat the differential case assembly with gear oil and install it to the front transaxle case.


b.
C200163

Coat the output shaft assembly with gear oil and install it to the front transaxle case.


c.
C199075

Install the manual transmission case with the 17 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


d.
C278825C01
0.906,1.698 1.417,2.167 1.417,2.167 1.646,2.167 false 1.635,0.354 1.958,0.354 false 1.729,2.083 2.188,2.281 0.458,0.198 10 SST 2.031,0.281 2.302,0.49 0.271,0.208 10 *1
*1 Rear Output Shaft Bearing Shim


Using SST and a torque wrench, turn the differential case assembly clockwise and counterclockwise 2 or 3 times to allow the bearings to settle.

SST
09564-50010  


e.

Using SST and a torque wrench, measure the preload (value A). Calculate the rear output shaft bearing preload using the following formula.

SST
09564-50010  

Formula:

Value A - Differential side bearing preload = Output shaft bearing preload


Preload (at starting):
New bearing:

3.17 to 6.35 N*m (32 to 65 kgf*cm, 28 to 56 in.*lbf)

Used bearing:

2.61 to 5.24 N*m (27 to 53 kgf*cm, 23 to 46 in.*lbf)


If the preload is not as specified, replace the rear output shaft bearing shim with another one of a different thickness. Use the table below to select a rear output shaft bearing shim which will ensure that the preload is within the specification.

Standard Bearing Shim Thickness:
Mark Specified Condition Mark Specified Condition
A 1.30 mm (0.511 in.) P 1.95 mm (0.768 in.)
B 1.35 mm (0.531 in.) Q 2.00 mm (0.787 in.)
C 1.40 mm (0.551 in.) R 2.05 mm (0.807 in.)
D 1.45 mm (0.571 in.) S 2.10 mm (0.827 in.)
E 1.50 mm (0.591 in.) T 2.15 mm (0.846 in.)
F 1.55 mm (0.610 in.) U 2.20 mm (0.866 in.)
G 1.60 mm (0.630 in.) V 2.25 mm (0.886 in.)
H 1.65 mm (0.650 in.) W 2.30 mm (0.906 in.)
J 1.70 mm (0.669 in.) X 2.35 mm (0.925 in.)
K 1.75 mm (0.689 in.) Y 2.40 mm (0.945 in.)
L 1.80 mm (0.709 in.) Z 2.45 mm (0.965 in.)
M 1.85 mm (0.728 in.) 1 2.50 mm (0.984 in.)
N 1.90 mm (0.748 in.) - -


HINT:

Select a thicker rear output shaft bearing shim to increase the preload, or a thinner rear output bearing shim to decrease the preload.



f.

Remove the 17 bolts and manual transmission case.


g.

Remove the output shaft assembly from the front transaxle case.


h.

Remove the differential case assembly from the front transaxle case.


i.

Replace the installed rear output shaft bearing shim with the one selected above.


Hide 33253H 8.INSTALL OUTER SHIFT LEVER OIL SEAL

a.
C200165C01
2.49,1.802 2.49,2.313 false 1.781,2.323 2.719,2.323 false 0.844,0.438 1.24,0.594 0.396,0.156 10 *a 2.771,2.24 3.063,2.396 0.292,0.156 10 SST
*a Depth


Using SST and a hammer, tap in a new outer shift lever oil seal to the manual transmission case.

SST
09950-60010  (09951-00280)
09950-70010  (09951-07100)

Standard depth:

0.5 to 1.0 mm (0.0197 to 0.0393 in.)



b.

Coat the lip of the outer shift lever oil seal with MP grease.


Hide 33253 9.INSTALL OUTER NO. 1 SHIFT LEVER

a.
C202194C01
0.51,2.354 0.906,2.521 0.396,0.167 10 *a
*a Depth


Install the inner No. 1 shift lever, outer shift lever spacer and outer No. 1 shift lever to the manual transmission case.


b.

Using a 5 mm pin punch and hammer, tap in the inner shift lever slotted spring pin to the inner No. 1 shift lever.

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



Hide 10.INSTALL NO. 1 OIL RECEIVER PIPE

a.
C202193

Install the No. 1 oil receiver pipe to the manual transmission case.

HINT:

Make sure that the No. 1 oil receiver pipe fully contacts the manual transmission case.



Hide 33101J 11.INSTALL BREATHER PLUG

a.
C200166N02
2.343,0.104 2.656,0.254 0.313,0.15 10 SST 2.308,0.187 2.037,0.187 false 2.037,0.187 2.037,0.505 false

Using SST and a hammer, tap in the breather plug to the front transaxle case.

SST
09350-30020  (09350-07110)


Hide 31105D 12.INSTALL FRONT TRANSAXLE CASE OIL SEAL

a.
C200167C01
3,1.698 2.396,1.698 false 2.396,1.698 1.958,2.135 false 2.844,0.188 3.156,0.365 0.313,0.177 10 *a 3.042,1.604 3.344,1.76 0.302,0.156 10 SST
*a Depth


Using SST and a hammer, tap in a new front transaxle case oil seal to the front transaxle case.

SST
09612-22011  

Standard depth:

1.0 to 2.0 mm (0.0394 to 0.0787 in.)



b.

Coat the lip of the front transaxle case oil seal with MP grease.


Hide 33449B 13.INSTALL TRANSMISSION MAGNET

a.
C202185

Clean the transmission magnet and install it to the front transaxle case.


Hide 33137 14.INSTALL INPUT SHAFT COVER

a.
C202192

Install the input shaft cover to the manual transmission case.

NOTICE:

Insert the input shaft cover key into the manual transmission case groove.



Hide 33311K 15.INSTALL REAR INPUT SHAFT BEARING SHIM

a.

Install the rear input shaft bearing shim onto the manual transmission case.

NOTICE:

Apply grease to the rear input shaft bearing shim to prevent it from falling off the case during assembly.



b.
C278658C01
1.167,2.396 1.76,2.396 false 0.844,3.51 1.313,3.51 1.313,3.51 1.313,3.927 false 0.635,0.573 0.948,0.771 0.313,0.198 10 *1 0.969,2.323 1.281,2.521 0.313,0.198 10 *2 0.635,3.417 0.948,3.615 0.313,0.198 10 *3 2.854,0.719 3.167,0.917 0.313,0.198 10 *a 2.844,2.323 3.156,2.521 0.313,0.198 10 *b 2.99,3.906 3.302,4.104 0.313,0.198 10 *c
*1 Manual Transmission Case
*2 Input Shaft Assembly
*3 Front Transaxle Case
*a Dimension A
*b Dimension C
*c Dimension B


Measure the distance between the end of the manual transmission case and installation surface of the rear input shaft bearing shim (Dimension A).


c.

Measure the distance between the end of the front transaxle case and installation surface of the front input shaft bearing (Dimension B).


d.

Measure the distance between both input shaft bearing outer races (Dimension C).

NOTICE:

Measure Dimension C with each bearing having no axial clearance.



e.

Calculate the rear input shaft bearing shim clearance using the following formula.

Formula:

(Dimension A + Dimension B) - Dimension C - Rear input shaft bearing shim thickness = Between 0 mm and 0.1 mm (0.00394 in.)


If the clearance is not as specified, replace the rear input shaft bearing shim with another one of a different thickness. Use the table below to select a rear input shaft bearing shim which will ensure that the clearance is within the specification.

Standard Rear Input Shaft Bearing Shim Thickness:
Mark Specified Condition Mark Specified Condition
A 1.15 mm (0.0453 in.) H 1.50 mm (0.0591 in.)
B 1.20 mm (0.0472 in.) J 1.55 mm (0.0610 in.)
C 1.25 mm (0.0492 in.) K 1.60 mm (0.0630 in.)
D 1.30 mm (0.0512 in.) L 1.65 mm (0.0650 in.)
E 1.35 mm (0.0531 in.) M 1.70 mm (0.0669 in.)
F 1.40 mm (0.0551 in.) N 1.75 mm (0.0689 in.)
G 1.45 mm (0.0571 in.) P 1.80 mm (0.0709 in.)



f.

Coat the selected rear input shaft bearing shim with MP grease, and then replace the installed rear input shaft bearing shim with the one selected above.

NOTICE:

Do not apply MP grease to the oil grooves.



Hide 16.INSTALL DIFFERENTIAL CASE ASSEMBLY

a.
C202182

Coat the differential case tapered roller bearing with gear oil and install it to the front transaxle case.


Hide 17.INSTALL INPUT SHAFT ASSEMBLY

a.

Apply gear oil to all sliding and rotating parts.


b.
C200169C01
2.43,0.65 2.614,0.792 0.184,0.142 10 *1 2.4,2.646 2.584,2.789 0.184,0.142 10 *2 1.816,2.727 2.354,2.727 false 2.087,1.169 2.087,0.705 false 2.087,0.705 2.365,0.705 false
*1 No. 1 Gear Shift Fork Shaft Assembly
*2 Output Shaft Assembly


Coat the No. 1 gear shift fork shaft assembly with gear oil and install it onto the output shaft assembly.


c.
C200170C01
2.608,0.613 2.78,0.764 0.172,0.151 10 *1 2.564,0.694 2.202,0.694 false 2.202,0.694 2.202,1.197 false 2.883,2.989 3.054,3.14 0.172,0.151 10 *2 2.838,3.068 2.434,3.068 false 2.436,3.071 2.436,3.578 false
*1 No. 2 Gear Shift Fork Shaft Assembly
*2 Input Shaft Assembly


Coat the No. 2 gear shift fork shaft assembly with gear oil and install it onto the input shaft assembly.


d.

Temporarily install the output shaft assembly together with the No. 1 gear shift fork shaft assembly to the input shaft assembly, and tie them with a rope or string.


e.
C202181

Install the input shaft assembly, output shaft assembly and 2 gear shift fork shaft assemblies to the front transaxle case.


Hide 33257C 18.INSTALL OUTER SELECT LEVER OIL SEAL

a.
C200173C01
0.594,2.208 1.49,2.208 false 1.49,2.208 2.073,2.115 false 1.146,0.208 1.448,0.417 0.302,0.208 10 *a 0.229,2.135 0.563,2.313 0.333,0.177 10 SST
*a Depth


Using SST and a hammer, tap in a new outer select lever oil seal to the front transaxle case.

SST
09950-60010  (09951-00250)
09950-70010  (09951-07100)

Standard depth:

0.5 to 1.0 mm (0.0197 to 0.0393 in.)



b.

Coat the lip of the outer select lever oil seal with MP grease.


Hide 33257 19.INSTALL OUTER SELECT LEVER

a.
C203006C01
2.938,0.25 2.688,0.25 false 2.688,0.25 2.604,0.521 false 2.948,0.167 3.146,0.333 0.198,0.167 10 *a
*a Mark


Install the outer select lever and inner select lever to the front transaxle case.

HINT:

Install the inner select lever with its mark positioned outside of the front transaxle case.



b.
C202180

Coat the threads of the inner select lever bolt with adhesive and install it.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 20.INSTALL SHIFT AND SELECT LEVER SHAFT ASSEMBLY

a.
C200174

Install the shift interlock plate and shift and select lever shaft assembly to the front transaxle case, and then turn them counterclockwise.

HINT:

When installing the shift interlock plate, make sure to engage it with the inner select lever.



Hide 33240 21.INSTALL REVERSE SHIFT ARM BRACKET ASSEMBLY

a.
C202179

Coat the threads of the 2 bolts with adhesive, and then, using a 6 mm hexagon wrench, install the reverse shift arm bracket assembly with the 2 bolts.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
17.2 N*m (175 kgf*cm, 13 ft.*lbf)


Hide 33211 22.INSTALL REVERSE SHIFT FORK

a.
C200913

Using a 5 mm pin punch and hammer, install the reverse shift fork slotted spring pin onto the reverse shift fork shaft.

Standard driven in depth:

-0.5 to 0.5 mm (-0.0196 to 0.0196 in.)


NOTICE:

Confirm the installation direction.



Hide 33211 23.INSTALL REVERSE SHIFT FORK SHAFT ASSEMBLY

a.
C278082

Coat the reverse shift fork shaft assembly with gear oil and install it onto the front transaxle case.


Hide 33402 24.INSTALL REVERSE IDLER GEAR SUB-ASSEMBLY

a.
C278081

Coat the reverse idler gear sub-assembly, reverse idler thrust washer and reverse idler gear shaft with gear oil, and install them as shown in the illustration.

NOTICE:
C278083C01
0.917,0.896 1.49,0.469 1.49,0.469 2.219,0.469 true 1.188,1.167 1.688,1 1.688,1 2.188,1 true 2.333,0.365 2.646,0.563 0.313,0.198 10 false *a 2.344,0.865 2.656,1.063 0.313,0.198 10 false *b
*a Case Hole
*b I-groove mark of the Reverse Idler Gear Shaft


Using the bolt hole of the case for reference, align the I-groove mark of the reverse idler gear shaft within the range shown (approximately 20°).


HINT:

Raise the edge of the reverse shift arm bracket assembly and connect the reverse shift arm bracket assembly to the reverse shift fork shaft assembly.



Hide 25.INSTALL MANUAL TRANSMISSION CASE

a.
C202201C01
0.906,2.885 0.906,2.615 0.906,2.615 1.115,2.375 false 0.854,2.948 1.167,3.146 0.313,0.198 10 *a
*a Seal Packing


Apply seal packing to the manual transmission case as shown in the illustration.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


Seal packing diameter:

1.2 mm (0.0472 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Assemble the parts within 10 minutes of application. Otherwise, the seal packing must be removed and reapplied.




b.
C202832

Push the outer No. 1 shift lever and install the manual transmission case.

HINT:

Pushing the outer No. 1 shift lever allows the manual transmission case to be installed.



c.
C202833

Turn the outer No. 1 shift lever counterclockwise and then pull it.


d.
C199075

Install the manual transmission case with the 17 bolts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


Hide 33253F 26.INSTALL OUTER SHIFT LEVER E-RING

a.
C199074

Install the outer shift lever E-ring to the outer No. 1 shift lever.


Hide 33111Q 27.INSTALL TRANSMISSION CASE OIL SEAL (for LH Side)

Hide 31105H 28.INSTALL TRANSAXLE CASE OIL SEAL (for RH Side)

Hide 33275C 29.INSTALL SHIFT DETENT BALL

a.

Install the 2 shift detent balls and 2 shift detent ball compression springs to the manual transmission case.

NOTICE:

Be careful not to drop the shift detent ball into the manual transmission case.



b.
C199073

Coat the threads of the 2 shift detent ball plugs with adhesive and install them using a 6 mm hexagon socket wrench.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


c.
C199072

Install the shift detent ball and shift detent ball compression spring to the manual transmission case.

NOTICE:

Be careful not to drop the lock ball pin into the manual transmission case.



d.

Coat the threads of the shift detent ball plug with adhesive and install it using a 6 mm hexagon socket wrench.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 33292A 30.INSTALL LOCK BALL PIN

a.

Install the lock ball pin and shift and select lever shaft compression spring to the manual transmission case.

NOTICE:

Be careful not to drop the lock ball pin into the manual transmission case.



b.
C199071

Coat the threads of the shift and select lever shaft straight screw with head plug with adhesive and install it using a 10 mm hexagon socket wrench.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


c.

Install the lock ball pin and shift and select lever shaft compression spring to the manual transmission case.

NOTICE:

Be careful not to drop the lock ball pin into the manual transmission case.



d.
C199069

Coat the threads of the shaft and select lever shaft straight screw with head plug with adhesive and install it using a 10 mm hexagon socket wrench.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent


Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 33451H 31.INSTALL REVERSE IDLER GEAR SHAFT BOLT

a.
C199070

Install a new gasket and the reverse idler gear shaft bolt to the manual transmission case.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


Hide 31477 32.INSTALL RELEASE CYLINDER BLEEDER PLUG

a.

Install the release cylinder bleeder plug to the clutch release bleeder sub-assembly.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


Hide 31478 33.INSTALL RELEASE CYLINDER BLEEDER PLUG CAP

a.

Install the release cylinder bleeder plug cap to the release cylinder bleeder plug.


Hide 31400 34.INSTALL CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY

Hide 31407B 35.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31407B 37.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 335A0 38.INSTALL CONTROL CABLE BRACKET ASSEMBLY

a.
C199067

Install the control cable bracket assembly to the manual transmission case with the 3 bolts.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


Hide 33111C 39.INSTALL TRANSMISSION CASE PLUG

a.
C206934

Install a new gasket and the transmission case plug to the manual transmission case.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 84210 40.INSTALL BACK-UP LIGHT SWITCH ASSEMBLY

a.
C199065

Using a 27 mm deep socket wrench, install a new gasket and the back-up light switch assembly to the manual transmission case.

Torque:
40.2 N*m (410 kgf*cm, 30 ft.*lbf)


Hide 33111A 41.INSTALL MANUAL TRANSMISSION FILLER PLUG

a.
C199064

Install a new gasket and the manual transmission filler plug to the manual transmission case.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)


Hide 33111A 42.INSTALL MANUAL TRANSMISSION DRAIN PLUG

a.
C199063

Install a new gasket and the manual transmission drain plug to the front transaxle case.

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)