Home › Engine / Hybrid System › 3ZR-FAE ENGINE CONTROL › SFI SYSTEM › 2012.12–2015.04
RM3090E _51 Engine / Hybrid System _008381 3ZR-FAE ENGINE CONTROL _0048627 SFI SYSTEM J

3ZR-FAE ENGINE CONTROL  SFI SYSTEM  VC Output Circuit  


DESCRIPTION

The ECM constantly generates a 5 V power source voltage from the battery voltage supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power source voltage to the sensors through the VC output circuit.

A206916E22
4.375,1.177 6.198,1.354 1.823,0.177 10 5 V Constant Voltage Circuit 5.354,2.031 6.365,2.188 1.01,0.156 10 Microprocessor 0.99,1.156 2.625,1.365 1.635,0.208 10 from EFI-MAIN NO.2 Fuse 0.938,1.479 2.604,1.646 1.667,0.167 10 from EFI-MAIN NO.1 Relay 2.906,1 3.427,1.219 0.521,0.219 10 BATT 0.313,2.135 2.635,2.677 2.323,0.542 10 Throttle Position Sensor, Accelerator Pedal Position Sensor, etc. (Sensors which have IC) 0.313,3.021 2.677,3.448 2.365,0.427 10 Engine Coolant Temperature Sensor, Intake Air Temperature Sensor, etc. 4.073,3.115 4.333,3.323 0.26,0.208 10 R 2.813,1.354 3.375,1.552 0.563,0.198 10 +B, +B2 3.167,2.271 3.458,2.5 0.292,0.229 10 VC 4.885,3.333 5.229,3.51 0.344,0.177 10 ECM

When the VC circuit is short-circuited, the microprocessor in the ECM and the sensors that are supplied with power through the VC circuit are inactivated because power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:

Under normal conditions, the MIL is illuminated when the ignition switch is turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A282859E04
5.333,0.99 5.917,1.219 0.583,0.229 10 ETA 5.323,1.813 6.094,2.208 0.771,0.396 10 VTA2 5.323,1.427 5.906,1.646 0.583,0.219 10 VTA1 5.323,0.625 6.083,0.927 0.76,0.302 10 VCTA 5.323,2.219 6.01,2.479 0.688,0.26 10 VCPA 5.333,4.031 5.875,4.271 0.542,0.24 10 EPA2 5.323,3.417 5.948,3.688 0.625,0.271 10 VPA2 5.323,2.583 6.083,2.854 0.76,0.271 10 VCP2 5.333,3.667 5.729,3.854 0.396,0.188 10 EPA 5.323,3.052 5.896,3.344 0.573,0.292 10 VPA 4.99,2.292 5.438,2.479 0.448,0.188 10 A62 5.042,2.125 5.479,2.406 0.438,0.281 10 53 4.99,3.021 5.406,3.313 0.417,0.292 10 A62 5.042,2.865 5.344,3.094 0.302,0.229 10 51 4.99,3.75 5.396,3.99 0.406,0.24 10 A62 5.042,3.594 5.375,3.813 0.333,0.219 10 52 4.99,2.656 5.448,2.917 0.458,0.26 10 A62 5.042,2.5 5.375,2.74 0.333,0.24 10 56 4.99,3.375 5.438,3.688 0.448,0.313 10 A62 5.052,3.219 5.479,3.5 0.427,0.281 10 54 4.99,4.115 5.396,4.417 0.406,0.302 10 A62 5.042,3.948 5.354,4.125 0.313,0.177 10 55 5.823,7.448 6.156,7.677 0.333,0.229 10 ECM 1.813,2.323 2.406,2.573 0.594,0.25 10 VCPA 1.844,4.125 2.396,4.417 0.552,0.292 10 EPA2 1.833,3.396 2.417,3.667 0.583,0.271 10 VPA2 1.823,2.667 2.385,2.927 0.563,0.26 10 VCP2 1.917,3.771 2.552,4.094 0.635,0.323 10 EPA 1.906,3.042 2.458,3.292 0.552,0.25 10 VPA 2.292,3.958 2.719,4.313 0.427,0.354 10 2 2.292,3.24 2.677,3.479 0.385,0.24 10 3 2.292,2.51 2.615,2.75 0.323,0.24 10 1 2.292,3.583 2.573,3.875 0.281,0.292 10 5 2.292,2.865 2.521,3.135 0.229,0.271 10 6 2.292,2.156 2.531,2.479 0.24,0.323 10 4 0.531,2.594 1.646,3.385 1.115,0.792 10 Accelerator Pedal Sensor Assembly 0.542,2.438 1.094,2.74 0.552,0.302 10 A6 1.99,0.729 2.406,0.99 0.417,0.26 10 VC 2.01,1.073 2.385,1.354 0.375,0.281 10 E2 1.906,1.448 2.385,1.75 0.479,0.302 10 VTA 1.833,1.781 2.375,2.031 0.542,0.25 10 VTA2 2.292,0.552 2.688,0.865 0.396,0.313 10 5 2.292,0.917 2.552,1.198 0.26,0.281 10 3 2.292,1.271 2.656,1.625 0.365,0.354 10 6 2.292,1.646 2.521,1.906 0.229,0.26 10 4 0.531,0.854 1.375,1.5 0.844,0.646 10 Throttle Body Assembly 0.552,0.698 1.073,1.01 0.521,0.313 10 B3 4.979,0.698 5.375,0.917 0.396,0.219 10 B75 5,0.521 5.406,0.76 0.406,0.24 10 115 4.979,1.427 5.542,1.729 0.563,0.302 10 B75 5.042,1.26 5.531,1.594 0.49,0.333 10 84 4.979,1.792 5.573,2.156 0.594,0.365 10 B75 5.042,1.625 5.365,1.854 0.323,0.229 10 83 4.979,1.063 5.365,1.271 0.385,0.208 10 B75 4.99,0.896 5.51,1.24 0.521,0.344 10 116 6.344,0.344 6.677,0.583 0.333,0.24 10 5 V 4.99,5.469 5.469,5.677 0.479,0.208 10 B75 4.99,4.74 5.427,5.052 0.438,0.313 10 B75 4.99,5.104 5.406,5.333 0.417,0.229 10 B75 4.979,6.938 5.385,7.198 0.406,0.26 10 B75 4.979,6.208 5.427,6.458 0.448,0.25 10 B75 4.99,6.573 5.49,6.792 0.5,0.219 10 B75 0.521,6.083 0.958,6.375 0.438,0.292 10 B41 0.5,6.25 1.729,6.927 1.229,0.677 10 Camshaft Position Sensor (for Exhaust Camshaft) 5.344,6.969 5.719,7.156 0.375,0.188 10 EV1+ 5.344,6.5 5.802,6.792 0.458,0.292 10 EV1- 5.042,6.792 5.406,7.042 0.365,0.25 10 80 5,6.427 5.427,6.646 0.427,0.219 10 112 5.333,5.5 5.906,5.76 0.573,0.26 10 VV1+ 2.292,6.427 2.552,6.708 0.26,0.281 10 2 2.292,6.771 2.625,7.073 0.333,0.302 10 1 2.292,6.063 2.698,6.396 0.406,0.333 10 3 2.292,5.021 2.448,5.25 0.156,0.229 10 2 2.292,5.396 2.698,5.719 0.406,0.323 10 1 2.292,4.594 2.552,4.927 0.26,0.333 10 3 5.323,6.135 5.875,6.406 0.552,0.271 10 VCE1 5,6.052 5.385,6.26 0.385,0.208 10 111 5.052,5.313 5.375,5.521 0.323,0.208 10 82 5,4.948 5.417,5.198 0.417,0.25 10 114 5,4.583 5.521,4.906 0.521,0.323 10 113 5.323,5.042 5.792,5.26 0.469,0.219 10 VV1- 5.323,4.667 5.875,4.906 0.552,0.24 10 VCV1 0.51,4.635 1.031,4.958 0.521,0.323 10 B39 0.5,4.792 1.635,5.479 1.135,0.688 10 Camshaft Position Sensor (for Intake Camshaft) 1.885,5.5 2.385,5.802 0.5,0.302 10 VVI+ 1.885,5.125 2.448,5.427 0.563,0.302 10 VVI- 1.979,4.76 2.313,5.01 0.333,0.25 10 VC 1.844,6.948 2.448,7.26 0.604,0.313 10 VVE+ 1.844,6.583 2.583,6.802 0.74,0.219 10 VVE- 1.906,6.208 2.406,6.417 0.5,0.208 10 VC2

A282860E03
5.823,3.427 6.167,3.635 0.344,0.208 10 false ECM 4.99,1.313 5.396,1.531 0.406,0.219 10 false B75 4.979,0.594 5.365,0.844 0.385,0.25 10 false B75 4.969,0.958 5.406,1.208 0.438,0.25 10 false B75 4.979,2.854 5.542,3.115 0.563,0.26 10 false B75 4.979,2.125 5.583,2.396 0.604,0.271 10 false B75 4.979,2.49 5.479,2.74 0.5,0.25 10 false B75 0.563,2.094 1.104,2.323 0.542,0.229 10 false B32 0.552,2.24 1.885,2.813 1.333,0.573 10 false Oil Pressure Sensor* 5.344,2.865 5.75,3.073 0.406,0.208 10 false PTO* 5.333,2.406 5.885,2.708 0.552,0.302 10 false EPTO* 5.031,2.688 5.552,2.99 0.521,0.302 10 false 89 4.99,2.323 5.479,2.573 0.49,0.25 10 false 121 5.344,1.344 5.74,1.51 0.396,0.167 10 false PIM 2.292,2.406 2.625,2.646 0.333,0.24 10 false 1 2.292,2.771 2.583,2.958 0.292,0.188 10 false 2 2.292,2.042 2.719,2.302 0.427,0.26 10 false 3 2.292,0.865 2.708,1.063 0.417,0.198 10 false 1 2.292,1.229 2.792,1.479 0.5,0.25 10 false 2 2.292,0.51 2.688,0.781 0.396,0.271 10 false 3 5.333,2.042 5.875,2.281 0.542,0.24 10 false VCPT* 4.99,1.958 5.396,2.167 0.406,0.208 10 false 120 5.031,1.167 5.344,1.375 0.313,0.208 10 false 87 4.979,0.792 5.427,1.073 0.448,0.281 10 false 119 4.979,0.427 5.521,0.802 0.542,0.375 10 false 118 5.333,0.875 5.844,1.198 0.51,0.323 10 false EPIM 5.323,0.51 5.885,0.781 0.563,0.271 10 false VCPM 0.563,0.563 1.01,0.792 0.448,0.229 10 false B45 0.563,0.708 1.667,1.208 1.104,0.5 10 false Manifold Absolute Pressure Sensor 1.938,1.333 2.458,1.615 0.521,0.281 10 false PIM 2.01,0.969 2.396,1.219 0.385,0.25 10 false E2 1.979,0.604 2.698,0.948 0.719,0.344 10 false VC 1.896,2.854 2.479,3.063 0.583,0.208 10 false PTO 2,2.51 2.417,2.76 0.417,0.25 10 false E2 1.979,2.146 2.5,2.438 0.521,0.292 10 false VC 3.49,2.021 3.583,2.167 0.094,0.146 10 false * 3.5,2.385 3.656,2.583 0.156,0.198 10 false * 3.5,2.74 3.583,2.906 0.083,0.167 10 false * 0.167,3.438 2.156,3.635 1.99,0.198 10 false *: for CVT Models

PROCEDURE

1.CHECK MIL CONDITION
a.

Check that the Malfunction Indicator Lamp (MIL) lights up when the ignition switch is turned to ON.

OK:

MIL lights up.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK CONNECTION BETWEEN GTS AND ECM
2.CHECK CONNECTION BETWEEN GTS AND ECM
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Check for communication between the GTS and ECM.

Result:
Result Proceed to
Communication is not possible A
Communication is possible B




A

3.CHECK MIL (THROTTLE POSITION SENSOR)

B

3.CHECK MIL (THROTTLE POSITION SENSOR)
a.

Disconnect the throttle body assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B


HINT:

Perform "Inspection After Repair" after replacing the throttle body assembly (Click here Engine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION).




A

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)

B

REPLACE THROTTLE BODY ASSEMBLY

4.CHECK MIL (ACCELERATOR PEDAL SENSOR ASSEMBLY)
a.

Disconnect the accelerator pedal sensor assembly connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

5.CHECK MIL (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))

B

REPLACE ACCELERATOR PEDAL SENSOR ASSEMBLY

5.CHECK MIL (CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT))
a.

Disconnect the camshaft position sensor (for intake camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

6.CHECK MIL (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))

B

REPLACE CAMSHAFT POSITION SENSOR (FOR INTAKE CAMSHAFT)

6.CHECK MIL (CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT))
a.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

7.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)

B

REPLACE CAMSHAFT POSITION SENSOR (FOR EXHAUST CAMSHAFT)

7.CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate (for CVT Models) A
MIL does not illuminate (for Manual Transaxle Models) B
MIL illuminates C




A

8.CHECK MIL (OIL PRESSURE SENSOR)

B

9.CHECK HARNESS AND CONNECTOR

C

8.CHECK MIL (OIL PRESSURE SENSOR)
a.

Disconnect the oil pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Check the MIL.

Result:
Result Proceed to
MIL does not illuminate A
MIL illuminates B




A

9.CHECK HARNESS AND CONNECTOR

B

REPLACE OIL PRESSURE SENSOR

9.CHECK HARNESS AND CONNECTOR
a.

Disconnect the throttle body assembly connector.


b.

Disconnect the accelerator pedal sensor assembly connector.


c.

Disconnect the camshaft position sensor (for intake camshaft) connector.


d.

Disconnect the camshaft position sensor (for exhaust camshaft) connector.


e.

Disconnect the manifold absolute pressure sensor connector.


f.

Disconnect the oil pressure sensor connector (for CVT Models).


g.

Disconnect the ECM connectors.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B75-115 (VCTA) - Body ground Always 10 kΩ or higher
A62-53 (VCPA) - Body ground Always 10 kΩ or higher
A62-56 (VCP2) - Body ground Always 10 kΩ or higher
B75-113 (VCV1) - Body ground Always 10 kΩ or higher
B75-111 (VCE1) - Body ground Always 10 kΩ or higher
B75-118 (VCPM) - Body ground Always 10 kΩ or higher
B75-120 (VCPT)* - Body ground Always 10 kΩ or higher


*: for CVT Models


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR