Home › Engine / Hybrid System › 2AD-FTV EMISSION CONTROL › EGR COOLER
RM3090E _51 Engine / Hybrid System _008737 2AD-FTV EMISSION CONTROL _0048709 EGR COOLER A

2AD-FTV EMISSION CONTROL  EGR COOLER  INSTALLATION  


PROCEDURE

Hide 25630 1.INSTALL NO. 2 EGR VALVE ASSEMBLY

a.

Install a new gasket and the No. 2 EGR valve assembly.

HINT:

Make sure that the claw of the gasket faces the EGR cooler.



Hide 25601 2.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

a.

Install a new gasket to the No. 2 EGR valve assembly.


b.

Temporarily install the No. 1 EGR pipe sub-assembly with the 2 bolts and 2 nuts.

HINT:

Tighten the bolts and nuts until there is no gap between the No. 1 EGR pipe sub-assembly, No. 2 EGR valve assembly and EGR cooler.



Hide 25601L 3.INSTALL EGR COOLER WITH PIPE ASSEMBLY

a.

Install a new O-ring to the EGR cooler.


b.

Install a new gasket to the EGR cooler and a new gasket to the No. 1 EGR pipe sub-assembly.


c.

Temporarily install the EGR cooler with pipe assembly with the 6 bolts and 2 nuts labeled A, B and C.

A273033
2.125,2.385 2.438,2.542 0.313,0.156 10 *1 5.219,0.073 5.375,0.271 0.156,0.198 10 A 4.458,1.49 4.615,1.688 0.156,0.198 10 B 6.229,1.313 6.385,1.51 0.156,0.198 10 C 1.26,0.313 1.417,0.51 0.156,0.198 10 A 2.177,0.354 2.333,0.552 0.156,0.198 10 B 0.229,0.938 0.385,1.135 0.156,0.198 10 C 0.531,2.198 0.688,2.396 0.156,0.198 10 D 1.698,0.323 1.854,0.521 0.156,0.198 10 A 1.49,1.615 1.646,1.813 0.156,0.198 10 A 1.969,1.646 2.125,1.844 0.156,0.198 10 A 2.667,0.948 2.823,1.146 0.156,0.198 10 B 0.958,0.083 1.115,0.281 0.156,0.198 10 C 0.875,2.198 1.031,2.396 0.156,0.198 10 D 0.396,1.833 0.552,2.031 0.156,0.198 10 D 1.031,1.833 1.188,2.031 0.156,0.198 10 D 4.531,0.594 4.844,0.75 0.313,0.156 10 *a 5.479,2.042 5.792,2.198 0.313,0.156 10 *b 3.781,1.99 4.094,2.146 0.313,0.156 10 *a
*1 Nut - -
*a 16 mm (0.630 in.) *b 25 mm (0.984 in.)



d.

Tighten the 2 bolts and 2 nuts labeled A shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


e.

Tighten the 2 bolts labeled B shown in the illustration.

Torque:
16 N*m (163 kgf*cm, 12 ft.*lbf)


f.

Tighten the 2 bolts labeled C shown in the illustration.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


g.

Tighten the 2 bolts and 2 nuts labeled D shown in the illustration.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


h.

Connect the vacuum transmitting hose to the No. 2 EGR valve assembly.


Hide 16264 4.INSTALL NO. 2 WATER BY-PASS HOSE

a.

Install the No. 2 water by-pass hose to the turbo oil outlet pipe and EGR cooler, and slide the 2 clamps to secure the hose.