Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  TRC OFF Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

for Segment Display Type:

Pressing the VSC OFF switch (traction control switch) turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns OFF, the TRC/TRAC OFF indicator light will come on.

If VSC and traction control turns OFF, the TRC/TRAC OFF indicator and VSC OFF indicator light will come on.

The TRC/TRAC OFF indicator light is illuminated when the TRC/TRAC control is prohibited by operating the VSC OFF switch (traction control switch).

By pressing the VSC OFF switch (traction control switch) for a short time, the TRC/TRAC OFF mode is activated, and the TRC/TRAC control is prohibited, and the TRC/TRAC OFF indicator light in the combination meter is illuminated.

By pressing the VSC OFF switch (traction control switch) for 3 seconds or more, the VSC OFF mode is activated, the VSC and TRC/TRAC controls are prohibited, and both the VSC OFF indicator light and the TRC/TRAC OFF indicator light are illuminated.

If there is a malfunction in the SFI system, the TRC/TRAC system will be prohibited and the TRC/TRAC OFF indicator light will turn on (for 2AR-FE, 3ZR-FE).

for Dot Display Type:

Pressing the VSC OFF switch (traction control switch) turns off traction control and pressing and holding this switch turns off traction and VSC controls. If traction control turns OFF, TRC OFF is displayed on the multi-information display.

If VSC and traction control turns OFF, TRC OFF is displayed on the multi-information display and the VSC OFF indicator light will come on.

TRC OFF is displayed on the multi-information display when the TRC control is prohibited by operating the VSC OFF switch (traction control switch).

By pressing the VSC OFF switch (traction control switch) for a short time, the TRC OFF mode is activated, TRC control is prohibited, and TRC OFF is displayed on the multi-information display.

By pressing the VSC OFF switch (traction control switch) for 3 seconds or more, the VSC OFF mode is activated, VSC and TRC controls are prohibited, the VSC OFF indicator light illuminates and TRC OFF is displayed on the multi-information display.

If there is a malfunction in the SFI system, the TRC system will be prohibited and the TRC OFF will be displayed on the multi-information display (for 2AR-FE, 3ZR-FE, 3ZR-FAE).

WIRING DIAGRAM

C279158E02
3.365,2.573 3.729,2.771 0.365,0.198 10 false G51 3.365,2.74 5.083,3.146 1.719,0.406 10 false VSC OFF Switch (Traction Control Switch) 3.25,2.156 3.406,2.354 0.156,0.198 10 false 3 4.208,2.156 4.365,2.354 0.156,0.198 10 false 6 3.406,2.354 3.563,2.552 0.156,0.198 10 false E 4.031,2.354 4.188,2.552 0.156,0.198 10 false + 5.396,2.146 5.708,2.344 0.313,0.198 10 false 30 5.656,2.26 6.115,2.458 0.458,0.198 10 false CSW 5.51,2.823 5.969,3.021 0.458,0.198 10 false A64 5.5,2.99 7.156,3.365 1.656,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 1.76,0.573 2.365,0.854 0.604,0.281 10 false CAN I/F 0.917,1.052 1.375,1.25 0.458,0.198 10 false CPU 1.063,2.958 2.396,3.146 1.333,0.188 10 false TRC/TRAC OFF*1 1.771,3.448 2.083,3.646 0.313,0.198 10 false IG 0.625,3.99 2.5,4.26 1.875,0.271 10 false Combination Meter Assembly 0.99,4.406 2.906,4.719 1.917,0.313 10 false : CAN Communication Line 1.542,1.792 2.615,2.427 1.073,0.635 10 false Multi-information Display*2 3.635,3.729 5.75,3.917 2.115,0.188 10 false *1: for Segment Display Type 3.656,4.063 5.583,4.26 1.927,0.198 10 false *2: for Dot Display Type

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK ENGINE TYPE
a.

Check the engine type.

Result:
Result Proceed to
2AR-FE A
3ZR-FAE
3ZR-FE
1AD-FTV B
2AD-FHV
2AD-FTV




A

2.CHECK SFI SYSTEM

B

3.CHECK IF SKID CONTROL ECU CONNECTOR SECURELY CONNECTED
2.CHECK SFI SYSTEM
a.

Check if SFI system DTCs are output

for 2AR-FE (w/ Canister Pump Module): Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/ Canister Pump Module)>DTC CHECK / CLEAR

for 2AR-FE (w/o Canister Pump Module): Click hereEngine / Hybrid System>2AR-FE ENGINE CONTROL>SFI SYSTEM(w/o Canister Pump Module)>DTC CHECK / CLEAR

for 3ZR-FAE: Click hereEngine / Hybrid System>3ZR-FAE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

for 3ZR-FE: Click hereEngine / Hybrid System>3ZR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Proceed to
DTCs are not output
DTCs are output (for 2AR-FE (w/ Canister Pump Module))
DTCs are output (for 2AR-FE (w/o Canister Pump Module))
DTCs are output (for 3ZR-FAE)
DTCs are output (for 3ZR-FE)




DTCs are not output

3.CHECK IF SKID CONTROL ECU CONNECTOR SECURELY CONNECTED

DTCs are output (for 2AR-FE (w/ Canister Pump Module))

DTCs are output (for 2AR-FE (w/o Canister Pump Module))

DTCs are output (for 3ZR-FAE)

DTCs are output (for 3ZR-FE)

3.CHECK IF SKID CONTROL ECU CONNECTOR SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

4.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

4.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output (for LHD)
DTC is output (for RHD)



DTC is not output

5.INSPECT BATTERY

DTC is output (for LHD)

DTC is output (for RHD)

5.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG (for 1AD-FTV)
NG (for 2AD-FHV)
NG (for 2AD-FTV)
NG (for 2AR-FE)
NG (for 3ZR-FAE)
NG (for 3ZR-FE)




OK

6.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)

NG (for 1AD-FTV)

NG (for 2AD-FHV)

NG (for 2AD-FTV)

NG (for 2AR-FE)

NG (for 3ZR-FAE)

NG (for 3ZR-FE)

6.CHECK HARNESS AND CONNECTOR (CSW TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


c.
C199357C58
1.625,0.083 2,0.333 0.375,0.25 1.781,1.844 1.854,1.396 false 0,0 0.313,0.156 0.313,0.156 10 false *a 1.688,0.125 2.146,0.323 0.458,0.198 10 false A64 1.604,1.865 2.063,2.073 0.458,0.208 10 false CSW
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A64-30 (CSW) - Body ground VSC OFF switch held on Below 1 Ω
A64-30 (CSW) - Body ground VSC OFF switch off (Not pressed) 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (TRC/VSC OFF MODE)

NG

8.INSPECT TRACTION CONTROL SWITCH
7.READ VALUE USING GTS (TRC/VSC OFF MODE)
a.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC/VSC Off Mode TRC/TRAC/VSC off mode Normal, TRC OFF, Unknown or VSC OFF Normal: Normal mode
TRC OFF: TRC/TRAC off mode
VSC OFF: VSC off mode
Unknown: Unspecified
Chassis > ABS/VSC/TRC > Data List
Tester Display
TRC/VSC Off Mode
50003 105 282

g.

Check that the mode display changes according to the VSC OFF switch (traction control switch) operation.

OK:

Display changes according to the switch operation.



Result:
Proceed to
OK
NG



OK

NG

8.INSPECT TRACTION CONTROL SWITCH
a.

Remove the VSC OFF switch (traction control switch).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>REMOVAL


b.

Inspect the VSC OFF switch (traction control switch).

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VSC OFF SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TRACTION CONTROL SWITCH)

NG

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TRACTION CONTROL SWITCH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-30 (CSW) - G51-6 (+) Always Below 1 Ω
G51-3 (E) - Body ground Always Below 1 Ω
A64-30 (CSW) or G51-6 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR