Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

Steering angle sensor signals are sent to the skid control ECU (brake actuator assembly) via the CAN communication system. When there is a malfunction in the CAN communication system, it will be detected by the steering angle sensor zero point malfunction diagnostic function.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1432 Steering Angle Sensor Power Source Voltage Malfunction Steering angle sensor power supply malfunction signal is received from steering angle sensor.
·

Steering angle sensor (Spiral with sensor cable sub-assembly) power supply

·

Steering angle sensor (Spiral with sensor cable sub-assembly)



WIRING DIAGRAM

C279156E01
3.281,2.979 5.375,3.333 2.094,0.354 10 Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly) 0.781,3.198 2.521,3.396 1.74,0.198 10 : CAN Communication Line 2.542,1.729 3.5,1.917 0.958,0.188 10 ECU-IG NO. 1 2.542,2.135 3.438,2.313 0.896,0.177 10 ECU-B NO. 1 4.01,1.583 4.323,1.781 0.313,0.198 10 IG 3.833,1.688 3.979,1.854 0.146,0.167 10 4 3.833,2.094 3.99,2.292 0.156,0.198 10 5 3.813,2.479 3.969,2.677 0.156,0.198 10 1 3.292,2.802 3.75,3 0.458,0.198 10 G12 4.021,1.99 4.479,2.188 0.458,0.198 10 BAT 3.99,2.396 4.448,2.594 0.458,0.198 10 ESS 5.563,2.031 6.021,2.229 0.458,0.198 10 A64 5.531,2.219 7.135,2.563 1.604,0.344 10 Skid Control ECU (Brake Actuator Assembly) 3.313,1.479 3.625,1.677 0.313,0.198 10 *1 2.854,0.51 3.167,0.708 0.313,0.198 10 *2 0.115,2.458 2.156,2.656 2.042,0.198 10 *1: w/o Stop and Start System 0.135,2.792 2.052,2.979 1.917,0.188 10 *2: w/ Stop and Start System 0.708,0.625 1.083,0.823 0.375,0.198 10 IGO1 1.146,0.729 1.458,0.927 0.313,0.198 10 12 0.083,1.25 1.146,1.625 1.063,0.375 10 Engine Stop and Start ECU*2 0.094,1.083 0.552,1.281 0.458,0.198 10 G87 1.24,1.573 2.146,1.76 0.906,0.188 10 from IG Circuit 1.396,1.948 2.198,2.135 0.802,0.188 10 from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove the steering angle sensor from the spiral with sensor cable sub-assembly.

·

When replacing the steering angle sensor (spiral with sensor cable sub-assembly), confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When U0073, U0124 and/or U0126 is output together with C1432, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>U0073

·

When the speed sensor or the yaw rate sensor (airbag sensor assembly) has trouble, DTCs for the steering angle sensor (spiral with sensor cable sub-assembly) may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor (spiral with sensor cable sub-assembly), inspect and repair the speed sensor and yaw rate sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor (spiral with sensor cable sub-assembly).



PROCEDURE

1.CHECK TERMINAL VOLTAGE (BAT TERMINAL)
a.

Turn the ignition switch off.


b.

Remove the steering wheel and the column cover lower.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL


c.
C266564C09
0.333,1.167 0.75,1.417 0.417,0.25 2.135,1.479 2.427,1.938 true 0.156,0.156 0.469,0.354 0.313,0.198 10 *a 0.417,1.208 0.802,1.479 0.385,0.271 10 G12 2.385,1.948 2.854,2.125 0.469,0.177 10 BAT
*a Front view of wire harness connector
(to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly])


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


d.

Disconnect the G12 steering angle sensor (spiral with sensor cable sub-assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G12-5 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IG TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BAT CIRCUIT)

2.CHECK TERMINAL VOLTAGE (IG TERMINAL)
a.

Turn the ignition switch to ON.


b.
C266564C10
0.333,1.167 0.75,1.417 0.417,0.25 1.875,1.479 1.635,1.938 true 0.156,0.156 0.469,0.354 0.313,0.198 10 *a 0.427,1.208 0.813,1.479 0.385,0.271 10 G12 1.521,1.948 1.74,2.115 0.219,0.167 10 IG
*a Front view of wire harness connector
(to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly])


Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
G12-4 (IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

3.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

NG (w/ Stop and Start System)

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Turn the ignition switch off.


b.
C266564C11
0.333,1.167 0.75,1.417 0.417,0.25 1.313,1.49 1.115,1.927 true 0.156,0.156 0.469,0.354 0.313,0.198 10 *a 0.438,1.208 0.823,1.479 0.385,0.271 10 G12 0.917,1.958 1.354,2.146 0.438,0.188 10 ESS
*a Front view of wire harness connector
(to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G12-1 (ESS) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ESS CIRCUIT)