Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM
RM3090E _55 Steering _008772 POWER ASSIST SYSTEMS _0049011 POWER STEERING SYSTEM C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM  C1511/11  Torque Sensor 1 Malfunction  C1512/11  Torque Sensor 2 Malfunction  C1513/11  Torque Sensor Deviation Excessive  C1514/11  Torque Sensor Power Supply Voltage Malfunction  


DESCRIPTION

The torque sensor converts the steering wheel rotation torque into electric signals and sends them to the power steering ECU assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Return-to-normal Condition
C1511/11 Torque Sensor 1 Malfunction Torque sensor malfunction
·

Electric power steering column sub-assembly (Torque sensor)

·

Power steering ECU assembly


On Ignition switch ON again
C1512/11 Torque Sensor 2 Malfunction Torque sensor malfunction
·

Electric power steering column sub-assembly (Torque sensor)

·

Power steering ECU assembly


On Ignition switch ON again
C1513/11 Torque Sensor Deviation Excessive Torque sensor malfunction
·

Electric power steering column sub-assembly (Torque sensor)

·

Power steering ECU assembly


On Ignition switch ON again
C1514/11 Torque Sensor Power Supply Voltage Malfunction Torque sensor malfunction
·

Electric power steering column sub-assembly (Torque sensor)

·

Power steering ECU assembly


On Ignition switch ON again

WIRING DIAGRAM

C240198
4.446,3.069 6.436,3.29 1.99,0.221 10 Power Steering ECU Assembly 0.558,2.946 3.062,3.31 2.503,0.365 10 Torque Sensor (built into Electric Power Steering Column Sub-assembly) 4.628,0.73 5.081,0.951 0.453,0.221 10 TRQ1 4.439,0.665 4.557,0.847 0.118,0.183 10 7 4.439,1.076 4.571,1.258 0.132,0.183 10 2 4.439,1.515 4.571,1.697 0.132,0.183 10 3 4.439,1.959 4.557,2.141 0.118,0.183 10 5 4.439,2.379 4.557,2.561 0.118,0.183 10 1 4.628,1.589 5.081,1.81 0.453,0.221 10 TRQV 4.628,2.037 5.081,2.258 0.453,0.221 10 TRQF 4.628,1.15 5.081,1.371 0.453,0.221 10 TRQ2 4.628,2.472 5.081,2.693 0.453,0.221 10 TRQG 4.446,2.893 4.687,3.075 0.241,0.182 10 a

CAUTION / NOTICE / HINT

NOTICE:

If the power steering ECU assembly has been replaced, perform assist map writing (Click here Steering>POWER ASSIST SYSTEMS>POWER STEERING SYSTEM>CALIBRATION).


PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (TORQUE SENSOR - ECU)
a.

Check the connection condition of the torque sensor connector.

OK:

Torque sensor connector is securely connected to the power steering ECU assembly.



Result:
Proceed to
OK
NG



OK

2.CHECK POWER STEERING ECU ASSEMBLY (TRQV, TRQF VOLTAGE)

NG

CONNECT CONNECTOR

2.CHECK POWER STEERING ECU ASSEMBLY (TRQV, TRQF VOLTAGE)
a.
C277341
1.021,2.781 1.292,2.021 false 1.438,2.115 1.51,2.781 false 1.469,2.01 2.156,2.771 false 1.375,2.833 1.99,3.031 0.615,0.198 10 TRQF 2.052,2.833 2.667,3.031 0.615,0.198 10 TRQG 0.823,2.833 1.438,3.031 0.615,0.198 10 TRQV 0.083,0.083 0.698,0.281 0.615,0.198 10 *a
*a Component with harness connected
(Power Steering ECU Assembly)


Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
a-3 (TRQV) - a-1 (TRQG) Engine running 8.5 to 10.5 V
a-5 (TRQF) - a-1 (TRQG) Engine running 3.35 to 3.37 V



Result:
Proceed to
OK
NG



OK

3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)

NG

REPLACE POWER STEERING ECU ASSEMBLY

3.CHECK POWER STEERING ECU ASSEMBLY (TRQ1, TRQ2 VOLTAGE)
a.
C277341
0.813,2.781 1.292,2.115 false 1.385,2.042 1.51,2.781 false 1.469,2.01 2.156,2.771 false 0.635,2.833 1.25,3.031 0.615,0.198 10 TRQ1 1.375,2.833 1.99,3.031 0.615,0.198 10 TRQ2 2.01,2.833 2.625,3.031 0.615,0.198 10 TRQG 0.115,0.115 0.375,0.344 0.26,0.229 10 *a
*a Component with harness connected
(Power Steering ECU Assembly)


Start the engine.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition (Steering Wheel Position) Specified Condition
a-7 (TRQ1) - a-1 (TRQG) Engine running Steering wheel not being turned (without load) 2.3 to 2.7 V
Engine running Steering wheel being turned to the right with vehicle stopped 2.5 to 4.7 V
Engine running Steering wheel being turned to the left with vehicle stopped 0.3 to 2.5 V
a-2 (TRQ2) - a-1 (TRQG) Engine running Steering wheel not being turned (without load) 2.3 to 2.7 V
Engine running Steering wheel being turned to the right with vehicle stopped 0.3 to 2.5 V
Engine running Steering wheel being turned to the left with vehicle stopped 2.5 to 4.7 V



c.

Under each condition, measure the voltage at terminals TRQ1 and TRQ2, and calculate the sum.

Standard Voltage:
Inspection Item Condition (Steering Wheel Position) Specified Condition
Sum of voltage between a-7 (TRQ1) and a-1 (TRQG) and voltage between a-2 (TRQ2) and a-1 (TRQG) Engine running Steering wheel not being turned (without load) Between 4.85 V and 5.35 V
Engine running Steering wheel being turned to the right with vehicle stopped
Engine running Steering wheel being turned to the left with vehicle stopped



Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPLACE ELECTRIC POWER STEERING COLUMN SUB-ASSEMBLY