Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM(for Start Function)
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0049280 ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function)  B2285  Steering Lock Position Signal Circuit Malfunction  


DESCRIPTION

This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication do not match.

HINT:

When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
B2285 Steering Lock Position Signal Circuit Malfunction The steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

Steering lock ECU (Steering lock actuator assembly)

·

Certification ECU (smart key ECU assembly)

·

Wire harness or connector


Disconnect the cable from the negative(-) battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) battery terminal. Wait 40 seconds or more with the engine switch off (with the steering wheel locked), then turn the engine switch on (ACC) (with the steering unlocked) and wait 40 seconds or more.

*: Only detected while a malfunction is present and the engine switch is on (IG)

Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The engine cannot be started. The ECU does not send an engine start request.

Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2285
Power Source Control:

Steering Unlock Switch


Entry&Start:
·

Power Supply Short

·

Motor Driver Short

·

Lock Bar Stuck Error


-

WIRING DIAGRAM

C279147E01
4.927,0.729 5.385,0.927 0.458,0.198 10 G82 4.083,0.875 4.542,1.073 0.458,0.198 10 AM2 2.594,0.719 3.5,0.927 0.906,0.208 10 from Battery 5.01,0.521 5.167,0.719 0.156,0.198 10 2 5.292,0.729 5.604,0.927 0.313,0.198 10 +B 4.938,1.448 5.396,1.646 0.458,0.198 10 G84 4.979,1.25 5.292,1.448 0.313,0.198 10 17 5.281,1.458 5.74,1.656 0.458,0.198 10 LIN 5.281,1.896 5.74,2.094 0.458,0.198 10 SLP 4.938,1.896 5.396,2.094 0.458,0.198 10 G84 4.969,1.698 5.281,1.896 0.313,0.198 10 26 4.979,2.167 5.292,2.365 0.313,0.198 10 11 4.938,2.375 5.396,2.573 0.458,0.198 10 G82 5.292,2.385 5.448,2.583 0.156,0.198 10 E 2.031,1.427 2.49,1.625 0.458,0.198 10 LIN 2.333,1.26 2.49,1.458 0.156,0.198 10 5 1.906,1.885 2.521,2.083 0.615,0.198 10 SLP1 2.344,1.76 2.5,1.958 0.156,0.198 10 4 0.865,2.302 1.177,2.5 0.313,0.198 10 G5 0.865,2.458 2.729,2.854 1.865,0.396 10 Steering Lock ECU (Steering Lock Actuator Assembly) 5.198,2.906 6.802,3.271 1.604,0.365 10 Certification ECU (Smart Key ECU Assembly) 1.052,3.333 2.656,3.552 1.604,0.219 10 : LIN Communication Line

CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the engine switch off to troubleshoot:

Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

·

The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING ). Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

·

Before replacing the certification ECU (smart key ECU assembly) or steering lock ECU (steering lock actuator assembly), refer to the entry and start system (for Start Function) precaution.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM(for Start Function)>PRECAUTION

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



PROCEDURE

1.CHECK FOR DTC (LIN COMMUNICATION SYSTEM)
a.

Check for DTCs.

Body Electrical > Entry&Start > Trouble Codes
50001 125
HINT:
·

If the steering wheel cannot be locked or unlocked, the engine switch cannot be turned on (IG) and the engine cannot be started.

·

If LIN communication is not available, the steering wheel cannot be locked or unlocked.



OK:

LIN communication system DTC B2785 is not output simultaneously.


Result:
Proceed to
OK
NG




OK

2.READ VALUE USING GTS (STEERING UNLOCK SWITCH)

NG

2.READ VALUE USING GTS (STEERING UNLOCK SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Power Source Control / Data List.


e.

According to the display on the GTS, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Switch State of steering unlock sensor signal output from steering lock actuator assembly ON or OFF ON: Steering unlocked
OFF: Steering locked
·

When the shift lever is in P*1 or N*2 and the engine switch is off, if any door is opened or closed, the steering is locked.

·

When the key is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.

·

The engine cannot be started when the steering unlock signal is off.


*1: except Manual Transaxle

*2: for Manual Transaxle


Body Electrical > Power Source Control > Data List
Tester Display
Steering Unlock Switch
50003 223 2
Result:
Proceed to
Data List item does not change
Data List item changes




Data List item does not change

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

Data List item changes

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)
a.
B268625C36
0.427,1.219 0.865,1.458 0.438,0.24 0.896,1.771 1.271,1.344 true 0.115,0.063 0.302,0.219 0.188,0.156 10 *a 0.521,1.24 0.948,1.406 0.427,0.167 10 G82 0.688,1.813 1.073,1.958 0.385,0.146 10 +B
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G82-2 (+B) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

4.CHECK HARNESS AND CONNECTOR (GROUND)
a.
B268625C38
0.521,1.323 0.958,1.563 0.438,0.24 2.063,1.583 2.448,1.792 true 0.115,0.063 0.302,0.219 0.188,0.156 10 false *a 2.521,1.74 2.906,1.885 0.385,0.146 10 false E 0.583,1.375 1.031,1.563 0.448,0.188 10 false G82
*a Rear view of wire harness connector
(to Certification ECU (Smart Key ECU Assembly))


Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G82-11 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.
C197722C40
0.219,0.875 0.604,1.135 0.385,0.26 2.344,1.792 2.188,1.792 2.188,1.792 1.771,1.167 false 0.323,0.24 0.635,0.396 0.313,0.156 10 false *a 0.313,0.917 0.625,1.073 0.313,0.156 10 false G5 2.417,1.729 3.031,1.927 0.615,0.198 10 false SLP1
*a Component with harness connected
(Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) tester probe → G5-4 (SLP1) Negative (-) tester probe → Body ground Steering locked* 10 kΩ or higher
Steering unlocked* Below 1 Ω


HINT:
·

*: If any of the doors are opened then closed with the shift lever in P and the engine switch off, the steering wheel will be locked. If the engine switch is then turned on (ACC) or on (IG), the steering wheel will be unlocked.

·

DTC B2285 may be stored due to a malfunction in the steering lock ECU (steering lock actuator assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator assembly) to the certification ECU (smart key ECU assembly) individually.




Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))
a.

Disconnect the G84 connector from the certification ECU (smart key ECU assembly).


b.

Disconnect the G5 connector from the steering lock ECU (steering lock actuator assembly).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G84-26 (SLP) - G5-4 (SLP1) Always Below 1 Ω
G84-26 (SLP) or G5-4 (SLP1) - Body ground 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR