Home › Audio / Visual / Telematics › NAVIGATION / MULTI INFO DISPLAY › NAVIGATION SYSTEM(for HDD) › 2012.12–2013.11
RM3090E _56 Audio / Visual / Telematics _008776 NAVIGATION / MULTI INFO DISPLAY _0048745 NAVIGATION SYSTEM(for HDD) J

NAVIGATION / MULTI INFO DISPLAY  NAVIGATION SYSTEM(for HDD)  Illumination Circuit  


DESCRIPTION

Power is supplied to the navigation ECU sub-assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

E269544E04
1.927,0.25 3.219,0.469 1.292,0.219 10 from TAIL Relay 3.896,0.406 4.427,0.604 0.531,0.198 10 PANEL 6,1.073 6.354,1.281 0.354,0.208 10 ILL+ 5.906,3.719 6.281,3.927 0.375,0.208 10 G137 5.917,3.875 7.073,4.281 1.156,0.406 10 Navigation ECU Sub-assembly 3.76,2.271 4.094,2.448 0.333,0.177 10 G8 3.177,2.188 3.479,2.365 0.302,0.177 10 -DP 3.156,0.99 3.448,1.198 0.292,0.208 10 IL+2 3.76,1.094 4.094,1.271 0.333,0.177 10 G8 2.729,1.083 2.99,1.271 0.26,0.188 10 z1 2.729,2.271 2.99,2.458 0.26,0.188 10 z1 2.948,2.698 3.854,3.104 0.906,0.406 10 Spiral Cable Sub-assembly 0.615,2.604 1.875,2.958 1.26,0.354 10 Steering Pad Switch RH Side 2.729,0.906 2.896,1.073 0.167,0.167 10 5 2.75,2.083 2.917,2.25 0.167,0.167 10 3 3.76,2.073 3.969,2.24 0.208,0.167 10 11 3.781,0.896 4.042,1.073 0.26,0.177 10 13 5.74,1 5.938,1.177 0.198,0.177 10 10 0.583,1.427 1.865,1.771 1.281,0.344 10 Steering Pad Switch LH Side 0.333,3.521 2.365,3.76 2.031,0.24 10 Steering Pad Switch Assembly 6.01,2.365 6.625,2.563 0.615,0.198 10 GND1 5.813,2.229 5.99,2.417 0.177,0.188 10 7

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>PRECAUTION

·

Inspect the fuse for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK ILLUMINATION
a.

Check if the illumination for the navigation ECU sub-assembly, steering pad switch assembly, heater control switch or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the head or tail position.

Result:
Result Proceed to
Illumination comes on for all components except steering pad switch assembly. A
Illumination comes on for all components except navigation ECU sub-assembly. B
No illumination comes on (navigation ECU sub-assembly, hazard switch, heater control switch, etc.). C




A

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY AND BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - BATTERY AND BODY GROUND)

C

2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
E270420C01
1.5,0.25 1.875,0.479 0.375,0.229 2.083,1.5 2.333,1.917 2.333,1.917 2.5,1.917 true 1.677,1.521 1.177,1.917 1.177,1.917 1,1.917 true 2.531,1.833 2.917,2.021 0.385,0.188 10 IL+2 0.083,0.104 0.396,0.302 0.313,0.198 10 *a 0.708,1.854 1.167,2.052 0.458,0.198 10 -DP 1.573,0.292 1.885,0.49 0.313,0.198 10 G8
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)


Disconnect the spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G8-11 (-DP) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G8-13 (IL+2) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STEERING PAD SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT STEERING PAD SWITCH ASSEMBLY
a.

Remove the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL


b.

Inspect the steering pad switch assembly.

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY


Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

5.CHECK HARNESS AND CONNECTOR (NAVIGATION ECU SUB-ASSEMBLY - BATTERY AND BODY GROUND)
a.
E259248C01
1.51,0.396 1.896,0.594 0.385,0.198 2.333,1.75 2.167,1.75 2.167,1.75 2.073,1.344 true 1.25,1.75 1.417,1.75 1.417,1.75 1.583,1.344 true 0.146,0.115 0.458,0.271 0.313,0.156 10 *a 1.542,0.417 2.094,0.635 0.552,0.219 10 G137 2.406,1.667 2.958,1.885 0.552,0.219 10 ILL+ 0.823,1.667 1.375,1.885 0.552,0.219 10 GND1
*a Front view of wire harness connector
(to Navigation ECU Sub-assembly)


Disconnect the navigation ECU sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G137-7 (GND1) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G137-10 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR