Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0048751 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  Downhill Assist Control Indicator Light Remains ON  


DESCRIPTION

When the downhill assist control switch is turned on, the downhill assist control function is available and the downhill assist control indicator light illuminates.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>CALIBRATION


PROCEDURE

1.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

2.CHECK CAN COMMUNICATION SYSTEM

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK CAN COMMUNICATION SYSTEM

Result:
Proceed to
DTC is not output
DTC is output (for LHD)
DTC is output (for RHD)



DTC is not output

3.CHECK HARNESS AND CONNECTOR (HDCS TERMINAL)

DTC is output (for LHD)

DTC is output (for RHD)

3.CHECK HARNESS AND CONNECTOR (HDCS TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the A64 skid control ECU (brake actuator assembly) connector.


c.
C199357C59
1.625,0.083 2,0.333 0.375,0.25 1.656,1.844 1.729,1.396 false 0,0 0.313,0.156 0.313,0.156 10 false *a 1.688,0.125 2.146,0.323 0.458,0.198 10 false A64 1.479,1.875 1.958,2.073 0.479,0.198 10 false HDCS

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A64-29 (HDCS) - Body ground Downhill assist control switch is pushed Below 1 Ω
A64-29 (HDCS) - Body ground Downhill assist control switch is not pushed 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL LIGHT)

NG

5.INSPECT DOWNHILL ASSIST CONTROL SWITCH
4.READ VALUE USING GTS (DOWNHILL ASSIST CONTROL LIGHT)
a.

Reconnect the A64 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Downhill Assist Control Light Downhill assist control indicator light ON or OFF ON: Indicator light on
OFF: Indicator light off
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Downhill Assist Control Light
50003 105 59

g.

Check the GTS display condition of the Downhill assist control indicator light.

Result:
Proceed to
Display of the Data List remains OFF
Display of the Data List remains ON




Display of the Data List remains OFF

Display of the Data List remains ON

5.INSPECT DOWNHILL ASSIST CONTROL SWITCH
a.

Turn the ignition switch off.


b.

c.

Result:
Result
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - DOWNHILL ASSIST CONTROL SWITCH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A64-29 (HDCS) - G29-4 Always Below 1 Ω
A64-29 (HDCS) or G29-4 - Body ground Always 10 kΩ or higher
G29-1 - Body ground Always Below 1 Ω


Result:
Result
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR