Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › 2012.12–2015.10
RM3090E _53 Suspension _008764 FRONT SUSPENSION _0049357 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  REMOVAL  


PROCEDURE

Hide 1. FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.REMOVE FRONT WHEELS

Hide 51443C 5.REMOVE REAR ENGINE UNDER COVER RH

a.
A297336

Remove the 3 clips and under cover.


Hide 51444A 6.REMOVE REAR ENGINE UNDER COVER LH

a.
A296295

Remove the 3 clips and under cover.


Hide 7.SECURE STEERING WHEEL

Hide 45259A 8.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 9.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45025D 10.REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 48810 11.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.
C279179C02
1.729,1.76 2.042,1.917 0.313,0.156 10 *a 0.365,1.479 0.677,1.635 0.313,0.156 10 *b
*a Turn
*b Hold


Remove the nut and disconnect the front stabilizer link assembly LH from the front stabilizer bar.

HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud bolt.



Hide 48820B 12.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45047 13.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 14.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 48069 15.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C127531

Remove the bolt and 2 nuts.


b.

Disconnect the front lower No. 1 suspension arm from the lower ball joint.


Hide 48068 16.DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 51218A 17.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH

a.
A296303

Remove the 4 bolts and front suspension member reinforcement LH.


Hide 51217A 18.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH

a.
A296302

Remove the 4 bolts and front suspension member reinforcement RH.


Hide 51425B 19.REMOVE ENGINE FRONT MOUNTING BRACKET REINFORCEMENT LOWER (for 1AD and 3ZR 2WD)

a.
A295897

Remove the 2 bolts and engine front mounting bracket reinforcement lower.


Hide 52258B 20.REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH

C149508

a.

Remove the 3 bolts and front suspension member rear brace LH.


Hide 52257A 21.REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Use the same procedure described for the LH side.


Hide 51201 22.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Remove the 2 bolts and 2 nuts, and disconnect the front suspension crossmember sub-assembly from the rear engine mounting insulator.

C232246


b.
C232813C03
2.26,2.229 2.49,2.229 false 2.49,2.219 2.49,1.635 false 0.385,1.99 0.385,1.604 true 0.396,1.76 1.688,1.76 true 1.688,1.76 1.688,1.333 true 1.24,1.75 1.24,1.448 true 2.625,1.229 3.021,1.229 true 2.104,2.135 2.417,2.292 0.313,0.156 10 *a 3.073,1.167 3.385,1.323 0.313,0.156 10 *b 0.313,2.042 0.625,2.198 0.313,0.156 10 *b
*a Engine Lifter
*b Attachment
V100155

Attachment placement location


Support the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.

NOTICE:
·

Make sure to secure the front suspension crossmember sub-assembly to prevent it from dropping.

·

Use the attachments to keep the front suspension crossmember sub-assembly level.

·

The front suspension crossmember sub-assembly is a heavy component. Make sure that it is supported securely.




c.

Remove the 2 bolts and front suspension crossmember sub-assembly.

C234335


d.

Slowly lower the front suspension crossmember sub-assembly.

NOTICE:

When lowering the front suspension crossmember sub-assembly, be careful not to damage the vehicle body or other components installed on the vehicle.



Hide 57104E 23.REMOVE FRONT CROSSMEMBER SUB-ASSEMBLY

a.
C205609

Using a jack, support the engine and transaxle assembly.


b.
A296304

Remove the 6 bolts and front crossmember sub-assembly.


Hide 48069 24.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.
C149510

Remove the 2 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front suspension crossmember sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



Hide 48068 25.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52255B 26.REMOVE FRONT SUSPENSION MEMBER BRACE

C232245

a.

Remove the 8 bolts and front suspension member brace from the front suspension crossmember sub-assembly.


Hide 48811 27.REMOVE FRONT STABILIZER BAR

a.
C154895

Remove the front stabilizer bar with the 2 front stabilizer bar bushings from the front suspension crossmember sub-assembly.


Hide 45510 28.REMOVE STEERING GEAR ASSEMBLY