Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › 2012.12–2014.10
RM3090E _55 Steering _008774 STEERING GEAR / LINKAGE _0049443 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.


·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.REMOVE FRONT WHEELS

Hide 51444 5.REMOVE REAR ENGINE UNDER COVER LH

Hide 51443 6.REMOVE REAR ENGINE UNDER COVER RH

Hide 45047 7.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

a.

Remove the cotter pin and castle nut.


b.

Install 2 spacers (SST spacer B) to the tie rod end sub-assembly LH so that there is a space of approximately 1 mm (0.0397 in.) between the arm and spacers.

SST
09960-20010  (09961-02060)

NOTICE:
·

Be sure to install the spacers (SST spacer B) as the steering knuckle spacer may shift.

·

As SST may become damaged, make sure the space between the arm and spacers is not 1 mm (0.0397 in.) or less.




c.

Using SST, separate the tie rod end sub-assembly LH from the steering knuckle.

SST
09960-20010  (09961-02010)

C275676C01
2.021,0.552 2.323,1.115 true 2.646,0.281 2.948,0.844 true 5.771,1.396 5.948,1.396 5.948,1.396 6.073,1.479 true 6.813,1.406 6.531,1.573 true 6.74,2.042 6.333,1.854 true 6.438,2.135 6.219,1.938 true 5.583,1.313 5.896,1.469 0.313,0.156 10 *1 6.76,1.99 7.073,2.146 0.313,0.156 10 *2 6.49,2.104 6.802,2.26 0.313,0.156 10 *3 6.844,1.302 7.156,1.458 0.313,0.156 10 *4 5.344,1.594 5.656,1.75 0.313,0.156 10 *a 6.844,1.583 7.156,1.74 0.313,0.156 10 *b 5.542,1.875 5.854,2.031 0.313,0.156 10 *c 2.5,0.177 2.813,0.333 0.313,0.156 10 *d 1.188,1.74 1.5,1.896 0.313,0.156 10 *e 1.75,0.438 2.208,0.635 0.458,0.198 10 SST
*1 Body *2 Claw
*3 Nut *4 Spacer B
*a Parallel *b 1 mm (0.0397 in.)
*c Molybdenum Grease Application Area *d String
*e Place the wrench here - -



d.

Using SST, disconnect the tie rod end sub-assembly LH from the steering knuckle.

NOTICE:
·

Apply molybdenum grease to the threads and the tip of SST.

·

Do not damage the dust cover.

·

Do not damage the ball joint dust cover.

·

Do not damage the steering knuckle.

·

As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

·

Make sure to tie the string of SST to the vehicle to prevent SST from dropping.




Hide 45046 8.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 45259A 9.REMOVE COLUMN HOLE COVER SILENCER SHEET

Hide 45260 10.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C275637

Secure the steering wheel with the seat belt in order to prevent rotation.

HINT:

This operation is useful to prevent damage to the spiral cable.



b.
C275677C01
0.75,0.844 0.229,1.594 0.229,1.594 0.813,1.01 true 0.073,1.531 0.385,1.688 0.313,0.156 10 *a
*a Matchmark


Place matchmarks on the sliding yoke of the steering intermediate shaft.


c.

Remove the bolt and disconnect the No. 2 steering intermediate shaft assembly.


Hide 48810 11.DISCONNECT FRONT STABILIZER LINK ASSEMBLY LH

Hide 48820B 12.DISCONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 51218A 13.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT LH

Hide 51217A 14.REMOVE FRONT SUSPENSION MEMBER REINFORCEMENT RH

HINT:

Use the same procedure described for the LH side.


Hide 51425B 15.REMOVE LOWER ENGINE FRONT MOUNTING BRACKET REINFORCEMENT (for 3ZR-FE (2WD) and 1AD-FTV)

Hide 52258B 16.REMOVE FRONT SUSPENSION MEMBER REAR BRACE LH

Hide 52257A 17.REMOVE FRONT SUSPENSION MEMBER REAR BRACE RH

HINT:

Use the same procedure described for the LH side.


Hide 45319A 18.REMOVE STEERING GEAR HEAT INSULATOR (for ZR Series Engine RHD)

a.

Remove the bolt and heat insulator from the steering gear.


Hide 51201 19.REMOVE FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

Hide 45025D 20.REMOVE NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

a.

Remove the clamp.


b.
C157411

Remove the No. 1 steering column sub-assembly from the steering gear hole cover.


Hide 45221 21.REMOVE STEERING INTERMEDIATE SHAFT

a.
C275678C01
2.271,1.135 1.646,0.365 1.646,0.365 2.323,1.042 false 1.479,0.26 1.792,0.417 0.313,0.156 10 *a
*a Matchmark


Place matchmarks on the steering intermediate shaft and steering gear assembly.


b.

Remove the bolt and steering intermediate shaft from the steering gear assembly.


Hide 45510 22.REMOVE STEERING GEAR ASSEMBLY

a.
C262291

Remove the 2 bolts, 2 nuts and steering gear assembly from the front suspension crossmember sub-assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut fixed in place.