Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › BLOCKING SYSTEM › 2012.12–2015.10
RM3090E _58 Vehicle Interior _008690 THEFT DETERRENT / KEYLESS ENTRY _0048167 BLOCKING SYSTEM J

THEFT DETERRENT / KEYLESS ENTRY  BLOCKING SYSTEM  Engine does not Start  


DESCRIPTION

If the engine does not start and no DTCs are output, the following conditions may apply:
·

There is a short circuit between the telephone transceiver assembly and the certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2.

·

The blocking system is set.


*1: w/ Entry and Start System

*2: w/o Entry and Start System


WIRING DIAGRAM

B341302E01
0.063,3.365 2.208,3.625 2.146,0.26 10 *2: w/o Entry and Start System 4.25,0.635 4.531,0.854 0.281,0.219 10 12 4.281,2.26 4.563,2.479 0.281,0.219 10 9 2.813,0.656 3.094,0.875 0.281,0.219 10 1 2.813,1.104 3.094,1.323 0.281,0.219 10 2 3,0.771 3.667,0.99 0.667,0.219 10 BLK1 2.99,1.219 3.51,1.438 0.521,0.219 10 BLK4 5.927,1.656 6.302,1.875 0.375,0.219 10 IMO 5.948,2.021 6.323,2.24 0.375,0.219 10 IMI 3.813,1.729 4.208,1.958 0.396,0.229 10 BLK2 3.813,2.052 4.188,2.271 0.375,0.219 10 BLK3 2.479,2.958 2.854,3.177 0.375,0.219 10 G58 0.813,1.604 1.323,1.802 0.51,0.198 10 G82*1 0.74,0.802 1.115,1.021 0.375,0.219 10 11*1 0.792,1.073 1.177,1.271 0.385,0.198 10 5*2 2.323,0.438 2.771,0.667 0.448,0.229 10 14*1 1.135,0.802 1.51,1 0.375,0.198 10 E*1 1.104,1.083 1.625,1.281 0.521,0.198 10 GND*2 1.958,0.771 2.333,0.969 0.375,0.198 10 EFII 1.927,1.229 2.302,1.427 0.375,0.198 10 EFIO 5.896,2.427 6.271,2.625 0.375,0.198 10 A62 0.813,1.76 2.604,2.146 1.792,0.385 10 Certification ECU (Smart Key ECU Assembly) 5.667,1.917 5.948,2.135 0.281,0.219 10 28 5.677,1.615 5.958,1.833 0.281,0.219 10 29 4.281,1.917 4.563,2.135 0.281,0.219 10 8 4.281,1.625 4.563,1.844 0.281,0.219 10 7 4.042,2.406 4.323,2.625 0.281,0.219 10 E 0.802,2.323 1.313,2.521 0.51,0.198 10 G88*2 2.344,1.115 2.667,1.302 0.323,0.188 10 13 3.958,0.719 4.333,0.938 0.375,0.219 10 +B 3.917,1.24 4.292,1.458 0.375,0.219 10 IG2 4.281,1.125 4.563,1.344 0.281,0.219 10 6 4.49,0.865 5.438,1.073 0.948,0.208 10 ECU-B NO. 1 4.75,1.375 5.167,1.583 0.417,0.208 10 IGN 5.74,0.698 6.688,0.906 0.948,0.208 10 from Battery 5.74,1.198 6.688,1.406 0.948,0.208 10 from IG2 Relay 2.323,0.635 2.74,0.833 0.417,0.198 10 12*2 2.469,3.125 4.792,3.354 2.323,0.229 10 Telephone Transceiver Assembly 0.052,3.083 2.198,3.344 2.146,0.26 10 *1: w/ Entry and Start System 0.792,2.49 2.896,2.75 2.104,0.26 10 Transponder Key ECU Assembly 5.885,2.604 6.354,2.833 0.469,0.229 10 ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Before troubleshooting this symptom, make sure no immobiliser system DTCs or blocking system DTCs are output. If output, troubleshoot the immobiliser system DTCs or blocking system DTCs first.

·

When replacing the telephone transceiver assembly and certification ECU (smart key ECU assembly)*1 or transponder key ECU assembly*2, refer to the Service Bulletin.

·

When the telephone transceiver assembly is replaced, it is necessary to set the contract mode.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


*1: w/ Entry and Start System

*2: w/o Entry and Start System



PROCEDURE

1.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Body Electrical > Entry&Start > Clear DTCs
50002 125
Body Electrical > Immobiliser > Clear DTCs
50002 260
Body Electrical > Telematics > Clear DTCs
50002 233

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

After 10 seconds have elapsed, check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Immobiliser > Trouble Codes
50001 260
Body Electrical > Telematics > Trouble Codes
50001 233

Result:
Proceed to
DTC is not output. A
SFI system (for 2AR-FE) DTC is output. B
SFI system (for 3ZR-FE) DTC is output. C
Immobiliser system (w/ Entry and Start System) DTC is output. D
Immobiliser system (w/o Entry and Start System) DTC is output. E
Entry and start system (for Start Function) DTC is output. F
Blocking system DTC is output. G



A

2.CHECK WHETHER ENGINE STARTS

B

C

D

E

F

G

2.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

3.CHECK BLOCKING SYSTEM (SETTING)
3.CHECK BLOCKING SYSTEM (SETTING)
a.

Check the blocking system setting.

HINT:

Check with the customer's contracted service provider to determine whether the blocking system is set.



Result:
Proceed to
Blocking system is unset.
Blocking system is set.



Blocking system is unset.

4.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)

Blocking system is set.

UNSET BLOCKING SYSTEM

4.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER SYSTEM UNSET)
a.

w/ Entry and Start System:

i.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


ii.

Press the engine switch with the brake pedal*1 or clutch pedal*2 released and check that the security indicator light changes from blinking to off at the same time the power source mode changes to on (ACC).

*1: except Manual Transaxle

*2: for Manual Transaxle


OK:

Security indicator light changes from blinking to off at the same time the power source mode changes to on (ACC).


HINT:

It is determined that the engine immobiliser function is operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to on (ACC).




b.

w/o Entry and Start System:

i.

Turn the ignition switch to ACC and check that the security indicator light changes from blinking to off at the same time the ignition switch is turned to ACC.

OK:

Security indicator light changes from blinking to off at the same time the ignition switch is turned to ACC.


HINT:

It is determined that the engine immobiliser function is operating correctly if the security indicator light changes from blinking to off at the same time the ignition switch is turned to ACC.




Result:
Proceed to
OK
NG (w/ Entry and Start System)
NG (w/o Entry and Start System)



OK

5.CHECK WHETHER ENGINE STARTS

NG (w/ Entry and Start System)

NG (w/o Entry and Start System)

5.CHECK WHETHER ENGINE STARTS
a.

Turn the ignition switch to ON.


b.

After 5 seconds have elapsed, start the engine.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

NG

6.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
6.CHECK TELEPHONE TRANSCEIVER ASSEMBLY
a.

Using an oscilloscope, check the waveform.

B340991C05
2.698,0.198 3.094,0.417 0.396,0.219 2.229,1.615 2.948,1.042 false 3.177,1.604 3.042,0.938 false 3.667,1.583 3.135,0.906 false 1.313,1.875 1.625,2.031 0.313,0.156 10 false *1 3.823,6.74 4.135,6.896 0.313,0.156 10 false *f 2.927,3.427 3.24,3.583 0.313,0.156 10 false *a 3.104,3.448 3.417,3.604 0.313,0.156 10 false *b 2.646,6.969 2.958,7.125 0.313,0.156 10 false *c 2.698,7.25 3.01,7.406 0.313,0.156 10 false *d 2.115,1.635 2.271,1.802 0.156,0.167 10 false E 3.573,1.635 3.969,1.823 0.396,0.188 10 false BLK1 3.031,1.635 3.427,1.823 0.396,0.188 10 false BLK4 2.76,0.24 3.073,0.427 0.313,0.188 10 false G58 3.021,2.281 3.552,2.5 0.531,0.219 10 false *4 1.375,3.979 1.688,4.135 0.313,0.156 10 false *2 1,3.313 1.49,3.531 0.49,0.219 10 false GND 1,5.344 1.49,5.563 0.49,0.219 10 false GND 2.448,4.281 2.885,4.5 0.438,0.219 10 false *3 3.438,4.281 4.042,4.51 0.604,0.229 10 false *5 3.333,5.479 3.646,5.635 0.313,0.156 10 false *a 3.51,5.5 3.823,5.656 0.313,0.156 10 false *b 4.542,7.25 4.854,7.406 0.313,0.156 10 false *d 4.667,6.958 4.979,7.115 0.313,0.156 10 false *c 1.427,6.698 1.771,7.031 0.344,0.333 10 false *e
*1 Waveform 1 *2 Waveform 2
*3 Waveform A *4 Waveform D
*5 Waveform E - -
*a Approximately 160 ms *b Approximately 270 ms
*c Approximately 40 ms *d Approximately 60 ms
*e Details of waveform A *f or


w/ Entry and Start System
Tester Connection Condition Tool Setting Specified Condition
G58-1 (BLK1) - G58-9 (E) Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal. 2 V/DIV., 500 ms./DIV. Pulse generation (See waveform 1)
G58-2 (BLK4) - G58-9 (E) Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal. 2 V/DIV., 500 ms./DIV. Pulse generation (See waveform 2)

w/o Entry and Start System
Tester Connection Condition Tool Setting Specified Condition
G58-1 (BLK1) - G58-9 (E) Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal. 2 V/DIV., 500 ms./DIV. Pulse generation (See waveform 1)
G58-2 (BLK4) - G58-9 (E) Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal. 2 V/DIV., 500 ms./DIV. Pulse generation (See waveform 2)

B340991C06
2.729,0.156 3.104,0.354 0.375,0.198 3.135,1.042 3.365,1.563 false 3.042,1.031 2.604,1.625 false 2.948,1.021 2.292,1.563 false 2.792,0.177 3.104,0.333 0.313,0.156 10 false G58 1.292,1.792 1.604,1.948 0.313,0.156 10 false *1 2.927,3.427 3.24,3.583 0.313,0.156 10 false *a 3.104,3.448 3.417,3.604 0.313,0.156 10 false *b 3.729,6.646 4.115,6.865 0.385,0.219 10 false *f 2.667,7.24 2.979,7.396 0.313,0.156 10 false *d 2.198,1.583 2.396,1.75 0.198,0.167 10 false E 2.417,1.656 2.813,1.823 0.396,0.167 10 false BLK3 3.271,1.646 3.781,1.813 0.51,0.167 10 false BLK2 1.375,3.958 1.688,4.115 0.313,0.156 10 false *2 0.979,3.323 1.354,3.479 0.375,0.156 10 false GND 1.021,5.344 1.396,5.5 0.375,0.156 10 false GND 3.333,5.458 3.646,5.615 0.313,0.156 10 false *a 3.531,5.469 3.844,5.625 0.313,0.156 10 false *b 2.24,4.302 2.708,4.469 0.469,0.167 10 false *3 2.656,6.958 2.969,7.115 0.313,0.156 10 false *c 4.667,6.958 4.979,7.115 0.313,0.156 10 false *c 4.583,7.26 4.896,7.417 0.313,0.156 10 false *d 1.281,6.51 2.781,6.708 1.5,0.198 10 false *e 3.427,4.292 4.01,4.49 0.583,0.198 10 false *5 3,2.281 3.615,2.448 0.615,0.167 10 false *4
*1 Waveform 1 *2 Waveform 2
*3 Waveform B *4 Waveform C
*5 Waveform F - -
*a Approximately 160 ms *b Approximately 270 ms
*c Approximately 40 ms *d Approximately 60 ms
*e Details of waveform B *f or


w/ Entry and Start System
Tester Connection Condition Tool Setting Specified Condition
G58-7 (BLK2) - G58-9 (E) Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal. 2 V/DIV., 500 ms./DIV. Pulse generation (See waveform 1)
G58-8 (BLK3) - G58-9 (E) Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of engine switch first being turned on (IG) after cable disconnected and reconnected to negative (-) battery terminal. 2 V/DIV., 500 ms./DIV. Pulse generation (See waveform 2)

w/o Entry and Start System
Tester Connection Condition Tool Setting Specified Condition
G58-8 (BLK3) - G58-9 (E) Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation (See waveform 1)
G58-8 (BLK3) - G58-9 (E) Check waveform within 3 seconds of starter operation and initial combustion, or within 3 seconds of ignition switch first being turned to ON after cable disconnected and reconnected to negative (-) battery terminal 2 V/DIV., 500 ms./DIV. Pulse generation (See waveform 2)

NOTICE:
·

The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

·

Check if the waveforms are output in alphabetical order. If they are not, proceed to the step indicated for the incorrect waveform.



OK:

The waveforms are output normally (refer to illustration).



Result:
Result Proceed to
OK (w/ Entry and Start System) A
OK (w/o Entry and Start System) B
Waveform A or E is abnormal (w/ Entry and Start System) C
Waveform A or E is abnormal (w/o Entry and Start System) D
Waveform B or F is abnormal E
Waveform C is abnormal F
Waveform D is abnormal (w/ Entry and Start System) G
Waveform D is abnormal (w/o Entry and Start System) H



A

7.REREGISTRATION

B

9.REREGISTRATION

C

11.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

D

15.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY)

E

19.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - ECM)

F

25.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - ECM)

G

29.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])

H

33.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY)
7.REREGISTRATION
a.

Reregister the communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

8.CHECK WHETHER ENGINE STARTS
8.CHECK WHETHER ENGINE STARTS
a.

Check if the problem symptom occurs when the engine is started using a registered key.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END

NG

12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
9.REREGISTRATION
a.

Reregister the communication ID.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

10.CHECK WHETHER ENGINE STARTS
10.CHECK WHETHER ENGINE STARTS
a.

Check if the problem symptom occurs when the engine is started using a registered key.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END

NG

16.REPLACE TRANSPONDER KEY ECU ASSEMBLY
11.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Disconnect the G58 telephone transceiver assembly connector.


b.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-2 (BLK4) - G82-13 (EFIO) Always Below 1 Ω
G58-2 (BLK4) - Body ground Always 10 kΩ or higher
G82-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Replace the certification ECU (smart key ECU assembly) with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

13.PERFORM REGISTRATION
13.PERFORM REGISTRATION
a.

Perform the registration.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

14.CHECK WHETHER ENGINE STARTS
14.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (CERTIFICATION ECU [SMART KEY ECU ASSEMBLY] WAS DEFECTIVE)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the G58 telephone transceiver assembly connector.


b.

Disconnect the G88 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-2 (BLK4) - G88-13 (EFIO) Always Below 1 Ω
G58-2 (BLK4) - Body ground Always 10 kΩ or higher
G88-13 (EFIO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.REPLACE TRANSPONDER KEY ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.REPLACE TRANSPONDER KEY ECU ASSEMBLY
a.

Replace the transponder key ECU assembly with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

17.PERFORM REGISTRATION
17.PERFORM REGISTRATION
a.

Perform the registration.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

18.CHECK WHETHER ENGINE STARTS
18.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (TRANSPONDER KEY ECU ASSEMBLY WAS DEFECTIVE)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

19.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - ECM)
a.

Disconnect the G58 telephone transceiver assembly connector.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-8 (BLK3) - A62-28 (IMI) Always Below 1 Ω
G58-8 (BLK3) - Body ground Always 10 kΩ or higher
A62-28 (IMI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

20.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

20.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Temporarily replace the telephone transceiver assembly with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

21.PERFORM REGISTRATION
21.PERFORM REGISTRATION
a.

Perform the registration.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

22.CHECK WHETHER ENGINE STARTS
22.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE TRANSCEIVER ASSEMBLY WAS DEFECTIVE)

NG

23.REPLACE ECM
23.REPLACE ECM
a.

Temporarily replace the ECM with a new one.


HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

24.CHECK DTC OUTPUT
24.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Body Electrical > Entry&Start > Clear DTCs
50002 125
Body Electrical > Immobiliser > Clear DTCs
50002 260
Body Electrical > Telematics > Clear DTCs
50002 233

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

After 10 seconds have elapsed, check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Immobiliser > Trouble Codes
50001 260
Body Electrical > Telematics > Trouble Codes
50001 233

Result:
Proceed to
DTC is not output. A
SFI system (for 2AR-FE) DTC is output. B
SFI system (for 3ZR-FE) DTC is output. C
Immobiliser system (w/ Entry and Start System) DTC is output. D
Immobiliser system (w/o Entry and Start System) DTC is output. E
Entry and start system (for Start Function) DTC is output. F
Blocking system DTC is output. G



A

END (POWER MANAGEMENT CONTROL ECU WAS DEFECTIVE)

B

C

D

E

F

G

25.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - ECM)
a.

Disconnect the G58 telephone transceiver assembly connector.


b.

Disconnect the A62 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-7 (BLK2) - A62-29 (IMO) Always Below 1 Ω
G58-7 (BLK2) - Body ground Always 10 kΩ or higher
A62-29 (IMO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

26.REPLACE ECM

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

26.REPLACE ECM
a.

Temporarily replace the ECM with a new one.


HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

27.CHECK DTC OUTPUT
27.CHECK DTC OUTPUT
a.

Clear the DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234
Body Electrical > Entry&Start > Clear DTCs
50002 125
Body Electrical > Immobiliser > Clear DTCs
50002 260
Body Electrical > Telematics > Clear DTCs
50002 233

b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON.


d.

After 10 seconds have elapsed, check for DTCs.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>BLOCKING SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Trouble Codes
50001 234
Body Electrical > Entry&Start > Trouble Codes
50001 125
Body Electrical > Immobiliser > Trouble Codes
50001 260
Body Electrical > Telematics > Trouble Codes
50001 233

Result:
Proceed to
DTC is not output. A
SFI system (for 2AR-FE) DTC is output. B
SFI system (for 3ZR-FE) DTC is output. C
Immobiliser system (w/ Entry and Start System) DTC is output. D
Immobiliser system (w/o Entry and Start System) DTC is output. E
Entry and start system (for Start Function) DTC is output. F
Blocking system DTC is output. G



A

28.CHECK WHETHER ENGINE STARTS

B

C

D

E

F

G

28.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (ECM WAS DEFECTIVE)

NG

REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

29.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - CERTIFICATION ECU [SMART KEY ECU ASSEMBLY])
a.

Disconnect the G58 telephone transceiver assembly connector.


b.

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-1 (BLK1) - G82-14 (EFII) Always Below 1 Ω
G58-1 (BLK1) - Body ground Always 10 kΩ or higher
G82-14 (EFII) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

30.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Temporarily replace the telephone transceiver assembly with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

31.PERFORM REGISTRATION
31.PERFORM REGISTRATION
a.

Perform the registration.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

32.CHECK WHETHER ENGINE STARTS
32.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE TRANSCEIVER ASSEMBLY WAS DEFECTIVE)

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

33.CHECK HARNESS AND CONNECTOR (TELEPHONE TRANSCEIVER ASSEMBLY - TRANSPONDER KEY ECU ASSEMBLY)
a.

Disconnect the G58 telephone transceiver assembly connector.


b.

Disconnect the G88 transponder key ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G58-1 (BLK1) - G88-12 (EFII) Always Below 1 Ω
G58-1 (BLK1) - Body ground Always 10 kΩ or higher
G88-12 (EFII) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

34.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.REPLACE TELEPHONE TRANSCEIVER ASSEMBLY
a.

Temporarily replace the telephone transceiver assembly with a new one.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

35.PERFORM REGISTRATION
35.PERFORM REGISTRATION
a.

Perform the registration.

HINT:

Refer to the Service Bulletin.



Result:
Proceed to
NEXT



NEXT

36.CHECK WHETHER ENGINE STARTS
36.CHECK WHETHER ENGINE STARTS
a.

Check that the engine starts normally.

OK:

Engine starts normally.



Result:
Proceed to
OK
NG



OK

END (TELEPHONE TRANSCEIVER ASSEMBLY WAS DEFECTIVE)

NG

REPLACE TRANSPONDER KEY ECU ASSEMBLY