Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR(w/o VSC) › 2012.12–2015.10
RM3090E _54 Brake _008767 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0049568 BRAKE ACTUATOR(w/o VSC) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(w/o VSC)  INSTALLATION  


PROCEDURE

Hide 44510 1.INSTALL BRAKE ACTUATOR WITH BRACKET

a.
C274693E01
1.292,1.917 1.448,2.115 0.156,0.198 10 C 1.583,1.948 1.74,2.135 0.156,0.188 10 B 2.229,1.948 2.396,2.115 0.167,0.167 10 A

Install the brake actuator with bracket with the 3 nuts. Tighten the 3 bolts uniformly in alphabetical order.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not damage the brake lines or wire harness.

·

Do not hold the actuator by the connector.

·

If the actuator is dropped, replace it.




b.

Connect the brake tube clamp to the bracket.


c.

Connect the brake actuator connector.

NOTICE:
·

Make sure that the connector is locked securely.

·

Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter.




Hide 2.CONNECT BRAKE LINE

a.
C274690E02
0.813,0.417 0.667,0.292 0.667,0.292 0.5,0.292 false 1.219,0.604 0.656,0.938 0.656,0.938 0.458,0.938 false 1.771,0.677 1.938,0.177 1.938,0.177 2.479,0.177 false 2.198,0.813 2.5,0.563 2.5,0.563 2.75,0.563 false 0.333,1.646 0.219,1.792 0.219,1.792 0.219,1.896 false 1.313,1.99 1.177,2.26 1.177,2.26 1.177,2.406 false 0.292,0.208 0.51,0.406 0.219,0.198 10 false *1 2.802,0.49 3.021,0.688 0.219,0.198 10 false *2 2.531,0.094 2.75,0.292 0.219,0.198 10 false *3 0.208,0.844 0.427,1.042 0.219,0.198 10 false *4 1.104,2.458 1.323,2.656 0.219,0.198 10 true *6 0.146,1.958 0.333,2.146 0.188,0.188 10 true *5

Temporarily install each brake line to the correct positions of the actuator assembly with bracket as shown in the illustration.

HINT:
·

*1: to front wheel cylinder RH

·

*2: to front wheel cylinder LH

·

*3: to rear wheel cylinder RH

·

*4: to rear wheel cylinder LH

·

*5: from front master cylinder

·

*6: from rear master cylinder




b.

Using a union nut wrench, tighten each brake line.

Torque:
15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 3.BLEED BRAKE SYSTEM

Hide 4.BLEED CLUTCH LINE (for Manual Transaxle)

Hide 5.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 6.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).