Home › Drivetrain › U660F AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSAXLE UNIT
RM3090E _52 Drivetrain _008436 U660F AUTOMATIC TRANSMISSION / TRANSAXLE _0047092 AUTOMATIC TRANSAXLE UNIT A

U660F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSAXLE UNIT  REASSEMBLY  


PROCEDURE

Hide 1. BEARING POSITION

a.

Check bearing position and installation direction.

C320818N02
1.344,4.292 1.74,4.5 0.396,0.208 10 false A 3.115,3.125 3.51,3.333 0.396,0.208 10 false B 4.958,2.938 5.354,3.146 0.396,0.208 10 false C

C357007N01
1.771,3.719 1.958,3.927 0.188,0.208 10 false D 4.396,2.563 4.583,2.771 0.188,0.208 10 false E 3.104,6.365 3.292,6.573 0.188,0.208 10 false F 5.99,5.052 6.177,5.26 0.188,0.208 10 false H 3.677,9.219 3.865,9.427 0.188,0.208 10 false G

Mark Front Race Diameter
Inside / Outside
Thrust Bearing Diameter
Inside / Outside
Rear Race Diameter
Inside / Outside mm
A - 57.7 mm (2.27 in.) / 75.2 mm (2.96 in.) -
B - 29.1 mm (1.15 in.) / 48.6 mm (1.91 in.) 30.7 mm (1.21 in.) / 48.3 mm (1.90 in.)
C - 62.6 mm (2.47 in.) / 82.4 mm (3.24 in.) 65.9 mm (2.59 in.) / 80.3 mm (3.16 in.)
D 59.4 mm (2.34 in.) / 77 mm (3.03 in.) 53.1 mm (2.09 in.) / 79 mm (3.11 in.) -
E - 56.1 mm (2.21 in.) / 80.9 mm (3.19 in.) -
F - 61.2 mm (2.41 in.) / 79 mm (3.11 in.) -
G - 28 mm (1.10 in.) / 47.1 mm (1.85 in.) 26.1 mm (1.03 in.) / 44 mm (1.73 in.)
H 52.2 mm (2.06 in.) / 70.4 mm (2.77 in.) 48.9 mm (1.93 in.) / 72.0 mm (2.84 in.) -


Hide 35782E 2.INSTALL COUNTER DRIVE GEAR BEARING

NOTICE:

Perform this procedure only when replacement of the counter drive gear bearing or transaxle case is necessary.


a.
C138721N02
2.413,0.816 2.755,0.978 0.341,0.163 10 SST 0.431,2.569 0.773,2.732 0.341,0.163 10 SST 1.589,1.012 2.376,0.902 2.376,0.902 1.76,1.183 false 1.621,2.114 0.832,2.653 0.832,2.653 1.645,2.47 false

Using SST and a press, install a new counter drive gear bearing (outer race) and new snap ring to the transaxle case.

SST
09950-60020  (09951-01030)
09950-70010  (09951-07100)


Hide 3.INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING OUTER RACE

a.
C274823N02
1.167,2.552 0.958,2.552 0.958,2.552 1.281,2.26 true 2.146,0.708 1.469,0.292 1.469,0.292 2.25,0.49 true 0.677,2.531 1.135,2.729 0.458,0.198 10 false SST 1.156,0.219 1.615,0.417 0.458,0.198 10 false SST

Using SST and a hammer, install a new counter driven gear rear tapered roller bearing outer race to the transaxle case.

SST
09950-60010  (09951-00650)
09950-70010  (09951-07100)

NOTICE:

Be sure to install the counter driven gear rear tapered roller bearing outer race so that there is no clearance between the bearing outer race and the transaxle case. If there is any clearance, the turning torque of the counter drive gear cannot be measured correctly.



Hide 41311F 4.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING OUTER RACE

a.
C196828N02
0.896,1.125 0.24,1.698 0.24,1.698 0.74,1.396 false 2.635,1.104 2.49,0.74 2.49,0.74 2.677,0.792 false 0.021,1.74 0.333,1.896 0.313,0.156 10 SST 2.229,0.563 2.615,0.74 0.385,0.177 10 SST

Using SST and a hammer, tap in a new front differential case rear tapered roller bearing outer race to the transaxle case.

SST
09950-60020  (09951-00790)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the bearing and transaxle case.



Hide 5.INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING OUTER RACE

a.
C194900N01
2.375,0.385 2.198,0.323 2.198,0.323 2.302,0.573 false 1.458,2.552 0.99,2.594 0.99,2.594 1.573,2.26 true 1.875,0.188 2.188,0.354 0.313,0.167 10 SST 0.688,2.552 1,2.719 0.313,0.167 10 SST

Install the shim to the transaxle housing.


b.

Using SST, install a new counter driven gear front tapered roller bearing outer race to the transaxle housing.

SST
09950-60020  (09951-00810)
09950-70010  (09951-07100)

NOTICE:

Be sure to install the counter driven gear front tapered roller bearing outer race so that there is no clearance between the shim and the transaxle housing.



Hide 41311E 6.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING OUTER RACE

a.

Install the shim to the transaxle housing.


b.
C196830N02
0.938,1.26 0.573,1.615 0.573,1.615 0.896,1.542 false 2.604,0.781 2.417,0.698 2.417,0.698 2.542,1.073 false 0.26,1.604 0.563,1.771 0.302,0.167 10 SST 2.167,0.521 2.469,0.688 0.302,0.167 10 SST

Using SST and a hammer, tap in a new front differential case front tapered roller bearing outer race to the transaxle housing.

SST
09950-60010  (09951-00480)
09950-70010  (09951-07150)

NOTICE:

Ensure that there is no clearance between the bearing and transaxle housing.



Hide 41311F 7.INSTALL FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING INNER RACE

a.
C317741N01
1,0.635 1.5,0.427 1.5,0.427 1.125,0.833 false 2.396,0.75 2.313,0.615 2.313,0.615 2.625,0.615 false 1.552,0.313 1.99,0.531 0.438,0.219 10 false SST 2.031,0.531 2.469,0.75 0.438,0.219 10 false SST

Using SST and a press, install a new front differential case rear tapered roller bearing inner race to the front differential case.

SST
09726-36010  
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case rear tapered roller bearing inner race cage when installing the front differential case rear tapered roller bearing inner race.

·

Ensure that there is no clearance between the front differential case rear tapered roller bearing inner race and front differential case.




Hide 41311E 8.INSTALL FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING INNER RACE

a.
C333248N01
0.875,0.865 0.563,0.594 0.563,0.594 1.021,0.469 true 0.583,0.604 0.927,0.729 false 0.24,0.521 0.698,0.719 0.458,0.198 10 false SST

Using SST and a press, install a new front differential case front tapered roller bearing inner race to the front differential case.

SST
09316-12010  
09649-17010  
09950-70010  (09951-07100)

NOTICE:
·

Do not damage the front differential case front tapered roller bearing inner race cage when installing the front differential case front tapered roller bearing inner race.

·

Ensure that there is no clearance between the front differential case front tapered roller bearing inner race and front differential case.




Hide 9.ADJUST DIFFERENTIAL SIDE BEARING PRELOAD

a.

Remove packing material from the contact surfaces between the transaxle housing and transaxle case.


b.
C209724

Install the front differential case to the transaxle case.


c.
C333246N01
1.5,1.604 1.781,2 1.781,2 2.25,1.646 false 1.781,1.99 1.896,1.646 false 0.854,1.813 1.177,2 1.177,2 1.313,1.781 false 1.177,2 1.115,1.854 false 0.5,1.417 0.24,1.292 0.24,1.292 0.625,1.656 false 0.521,1.031 0.24,1.292 0.24,1.292 0.479,1.229 false 1.104,0.49 0.729,0.229 0.729,0.229 0.969,0.635 false 1.313,0.396 0.729,0.229 0.729,0.229 0.802,0.719 false 2.573,0.823 2.594,0.24 2.594,0.24 1.74,0.438 false 2.271,0.656 2.594,0.24 2.594,0.24 2,0.531 false 2.542,1.385 2.979,1.198 2.979,1.198 2.646,1.083 false 0.625,0.073 0.781,0.271 0.156,0.198 10 false A 2.646,0.135 2.802,0.333 0.156,0.198 10 false A 3.021,1.125 3.177,1.323 0.156,0.198 10 false A 1.146,2.021 1.292,2.177 0.146,0.156 10 false A 0.104,1.219 0.26,1.417 0.156,0.198 10 false A 1.729,2.021 1.885,2.177 0.156,0.156 10 false B

Install the transaxle housing to the transaxle case with the 20 bolts.

Torque:
for Bolt A : 22.7 N*m (231 kgf*cm, 17 ft.*lbf)
for Bolt B : 30.6 N*m (312 kgf*cm, 23 ft.*lbf)


d.
C314367N01
1.333,4.281 1.052,4.281 1.052,4.281 1.052,3.156 true 1.385,4.177 1.927,4.448 0.542,0.271 10 false SST

Using SST and a torque wrench, measure the turning torque of the differential side bearing while rotating SST at 10 rpm.

SST
09564-33010  

Turning torque:

1.05 to 1.93 N*m (10.71 to 19.68 kgf*cm, 9.30 to 17.08 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim so that the turning torque is within the specified range.

Shim Thickness:
Thickness Thickness Thickness Thickness
2.000 mm (0.0787 in.) 2.225 mm (0.0876 in.) 2.450 mm (0.0965 in.) 2.675 mm (0.105 in.)
2.025 mm (0.0797 in.) 2.250 mm (0.0886 in.) 2.475 mm (0.0974 in.) 2.700 mm (0.106 in.)
2.050 mm (0.0807 in.) 2.275 mm (0.0896 in.) 2.500 mm (0.0984 in.) 2.725 mm (0.107 in.)
2.075 mm (0.0817 in.) 2.300 mm (0.0906 in.) 2.525 mm (0.0994 in.) 2.750 mm (0.108 in.)
2.100 mm (0.0827 in.) 2.325 mm (0.0915 in.) 2.550 mm (0.100 in.) 2.775 mm (0.109 in.)
2.125 mm (0.0837 in.) 2.350 mm (0.0925 in.) 2.575 mm (0.101 in.) 2.800 mm (0.110 in.)
2.150 mm (0.0846 in.) 2.375 mm (0.0935 in.) 2.600 mm (0.102 in.) 2.825 mm (0.111 in.)
2.175 mm (0.0856 in.) 2.400 mm (0.0945 in.) 2.625 mm (0.103 in.) 2.850 mm (0.112 in.)
2.200 mm (0.0866 in.) 2.425 mm (0.0955 in.) 2.650 mm (0.104 in.) 2.875 mm (0.113 in.)


e.
C205232

Remove the 20 bolts and the transaxle housing from the transaxle case.


f.
C209724

Remove the front differential case from the transaxle case.


Hide 10.INSTALL COUNTER DRIVEN GEAR FRONT TAPERED ROLLER BEARING

a.
C194896N01
0.594,0.604 0.677,0.604 0.677,0.604 0.781,0.979 false 2.385,0.677 2.51,0.677 false 0.26,0.531 0.656,0.719 0.396,0.188 10 SST 2.083,0.604 2.448,0.771 0.365,0.167 10 SST

Using SST and a press, install a new counter driven gear front tapered roller bearing to the counter driven gear.

SST
09950-60010  (09951-00530)

NOTICE:

Be sure to install the counter driven gear front tapered roller bearing so that there is no clearance between the bearing and the counter driven gear. If there is any clearance, the turning torque of the counter drive gear cannot be measured correctly.



Hide 11.INSTALL COUNTER DRIVEN GEAR REAR TAPERED ROLLER BEARING

a.
C194897N01
0.583,0.76 0.667,0.76 0.667,0.76 0.802,1.146 false 2.281,0.833 2.458,0.833 false 0.281,0.688 0.656,0.854 0.375,0.167 10 SST 2,0.771 2.385,0.938 0.385,0.167 10 SST

Using SST and a press, install a new counter driven gear rear tapered roller bearing to the counter driven gear.

SST
09950-60010  (09951-00420)

NOTICE:

Be sure to install the counter driven gear rear tapered roller bearing so that there is no clearance between each of them and the counter driven gear.



Hide 12.ADJUST COUNTER DRIVEN GEAR PRELOAD

a.
C209725

Install the counter driven gear and front differential case to the transaxle case.


b.
C333246N01
1.5,1.604 1.781,2 1.781,2 2.25,1.646 false 1.781,1.99 1.896,1.646 false 0.854,1.813 1.177,2 1.177,2 1.313,1.781 false 1.177,2 1.115,1.854 false 0.5,1.417 0.24,1.292 0.24,1.292 0.625,1.656 false 0.521,1.031 0.24,1.292 0.24,1.292 0.479,1.229 false 1.104,0.49 0.729,0.229 0.729,0.229 0.969,0.635 false 1.313,0.396 0.729,0.229 0.729,0.229 0.802,0.719 false 2.573,0.823 2.594,0.24 2.594,0.24 1.74,0.438 false 2.271,0.656 2.594,0.24 2.594,0.24 2,0.531 false 2.542,1.385 2.979,1.198 2.979,1.198 2.646,1.083 false 0.625,0.073 0.781,0.271 0.156,0.198 10 false A 2.646,0.135 2.802,0.333 0.156,0.198 10 false A 3.021,1.125 3.177,1.323 0.156,0.198 10 false A 1.146,2.021 1.292,2.177 0.146,0.156 10 false A 0.104,1.219 0.26,1.417 0.156,0.198 10 false A 1.729,2.021 1.885,2.177 0.156,0.156 10 false B

Install the transaxle housing to the transaxle case with the 20 bolts.

Torque:
for Bolt A : 22.7 N*m (231 kgf*cm, 17 ft.*lbf)
for Bolt B : 30.6 N*m (312 kgf*cm, 23 ft.*lbf)


c.
C317726N01
1.25,4.354 1.021,4.354 1.021,4.354 1.021,3.406 false 1.313,4.281 1.802,4.531 0.49,0.25 10 false SST

Using SST and a torque wrench, measure the turning torque of the counter driven gear while rotating SST at 10 rpm.

SST
09564-33010  

Turning torque:

Differential side bearing preload + 3.48 to 6.48 N*m (35.49 to 66.07 kgf*cm, 30.81 to 57.35 in.*lbf)


If the turning torque is not within the specified range, refer to the table below to select a shim of the counter driven gear front tapered roller bearing outer race so that the turning torque is within the specified range.

Shim Thickness:
Thickness Thickness Thickness Thickness
2.000 mm (0.0787 in.) 2.275 mm (0.0896 in.) 2.525 mm (0.0994 in.) 2.775 mm (0.109 in.)
2.025 mm (0.0797 in.) 2.300 mm (0.0906 in.) 2.550 mm (0.100 in.) 2.800 mm (0.110 in.)
2.050 mm (0.0807 in.) 2.325 mm (0.0915 in.) 2.575 mm (0.101 in.) 2.825 mm (0.111 in.)
2.075 mm (0.0817 in.) 2.350 mm (0.0925 in.) 2.600 mm (0.102 in.) 2.850 mm (0.112 in.)
2.100 mm (0.0827 in.) 2.375 mm (0.0935 in.) 2.625 mm (0.103 in.) 2.875 mm (0.113 in.)
2.125 mm (0.0837 in.) 2.400 mm (0.0945 in.) 2.650 mm (0.104 in.) 2.900 mm (0.114 in.)
2.150 mm (0.0846 in.) 2.425 mm (0.0955 in.) 2.675 mm (0.105 in.) 2.925 mm (0.115 in.)
2.175 mm (0.0856 in.) 2.450 mm (0.0965 in.) 2.700 mm (0.106 in.) 2.950 mm (0.116 in.)
2.200 mm (0.0866 in.) 2.475 mm (0.0974 in.) 2.725 mm (0.107 in.) 2.975 mm (0.117 in.)
2.225 mm (0.0876 in.) 2.500 mm (0.0984 in.) 2.750 mm (0.108 in.) 3.000 mm (0.118 in.)
2.250 mm (0.0886 in.) - - -


d.
C205232

Remove the 20 bolts and the transaxle housing from the transaxle case.


e.
C209724

Remove the counter driven gear and front differential case from the transaxle case.


Hide 31105H 13.INSTALL TRANSAXLE CASE OIL SEAL LH

a.

Coat the lip of a new transaxle case oil seal LH with MP grease.


b.
C188706N01
1.417,1.219 0.406,2.115 0.406,2.115 1.323,1.521 true 2.063,1.885 2.833,1.438 2.833,1.438 2.479,1.969 true 0.042,2.042 0.344,2.208 0.302,0.167 10 SST 2.875,1.333 3.177,1.5 0.302,0.167 10 SST

Using SST and a hammer, tap in a new transaxle case oil seal LH.

SST
09316-10010  09950-70010  (09951-07100)

Standard depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:

Make sure that the transaxle oil seal LH is installed in the correct direction.



Hide 31105H 14.INSTALL TRANSAXLE CASE OIL SEAL RH (OUTER)

a.

Coat the lip of a new transaxle case oil seal RH (outer) with MP grease.


b.
C209728N01
1.219,1.854 1.281,2.458 1.281,2.458 0.917,2.083 true 3.292,1.656 3.177,2.479 3.177,2.479 2.906,2.073 true 1.188,2.49 1.5,2.667 0.313,0.177 10 SST 3.01,2.49 3.323,2.667 0.313,0.177 10 SST

Using SST and a hammer, tap in the transaxle case oil seal RH (outer).

SST
09649-17010  09950-70010  (09951-07200)

Standard depth:

5.5 to 6.5 mm (0.217 to 0.255 in.)


NOTICE:

Make sure that the transaxle case oil seal RH (outer) is installed in the correct direction.



Hide 35506F 15.INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

a.
C274816N01
1.813,1.365 2.083,1.365 2.083,1.365 1.792,0.969 true 1.219,2.219 1.031,1.948 1.031,1.948 1.24,1.948 false 2.115,1.292 2.573,1.49 0.458,0.198 10 SST 0.75,1.865 1.208,2.063 0.458,0.198 10 SST

Coat the lip of a new manual valve lever shaft oil seal with MP grease.


b.

Using SST and a hammer, install the manual valve lever shaft oil seal to the transaxle case.

SST
09950-60010  (09951-00230)
09950-70010  (09951-07100)

Oil seal driven in depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)



Hide 35506 16.INSTALL MANUAL VALVE LEVER SHAFT SUB-ASSEMBLY

a.
C201357

Install the manual valve lever shaft sub-assembly to the transaxle case.

NOTICE:

Do not damage the manual valve lever shaft oil seal while installing the manual valve lever shaft sub-assembly to the transaxle case.



b.
C274815

Using needle-nose pliers, install the manual valve shaft retainer spring to the transaxle case.


Hide 35501 17.INSTALL PARKING LOCK ROD SUB-ASSEMBLY

a.
C201355C01
0.771,1.51 0.896,1.51 0.896,1.51 1.698,1.219 true 2.052,0.75 2.458,0.146 2.458,0.146 2.604,0.146 true 0.604,1.427 0.917,1.583 0.313,0.156 10 false *1 2.656,0.063 2.969,0.219 0.313,0.156 10 false *2
*1 Parking Lock Rod Sub-assembly
*2 Manual Valve Lever Shaft Sub-assembly


Align the slot with the notches on the manual valve lever shaft sub-assembly and install the parking lock rod sub-assembly.


Hide 35409 18.INSTALL MANUAL DETENT SPRING SUB-ASSEMBLY

a.
C201354

Install the manual detent spring sub-assembly and cover to the transaxle case with the bolt.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)

NOTICE:

Make sure to install the manual detent spring sub-assembly first and then the cover.



Hide 35623 19.INSTALL NO. 3 BRAKE PISTON

a.
C137432

Coat the contact surface of the transaxle case with ATF.


b.

Coat the lip of the No. 3 brake piston with ATF.


c.
C274817

Temporarily install the pawl stopper plate to the transaxle case with the 2 bolts.


d.

Press the No. 3 brake piston into the transaxle case.

NOTICE:
·

Make sure that the lip of the No. 3 brake piston is not twisted and does not get caught in the transaxle case.

·

After installation, make sure that the protrusions on the No. 3 brake piston and the grooves on the pawl stopper plate are aligned.



HINT:

Use the installation surface of the brake piston return spring to press the No. 3 brake piston into the transaxle case.



e.
C141536C01
0.813,1.781 2.302,0.354 2.302,0.354 2.042,0.917 false 0.948,0.146 1.229,0.146 1.229,0.146 0.74,1.438 false 2.292,2.156 2.458,2.052 false 2.323,0.229 2.5,0.417 0.177,0.188 10 *1 2.49,1.958 2.688,2.125 0.198,0.167 10 *2 0.76,0.083 0.938,0.26 0.177,0.177 10 *2
*1 Brake Piston Return Spring
*2 No. 3 Brake Piston


Install the brake piston return spring to the transaxle case.


f.

Remove the 2 bolts and pawl stopper plate from the transaxle case.


g.
C281627C01
2.031,2.656 1.885,2.656 1.885,2.656 1.708,1.865 true 1.156,1.573 0.917,0.563 0.917,0.563 0.719,0.563 true 2.083,2.573 2.396,2.729 0.313,0.156 10 false *a 0.406,0.49 0.792,0.667 0.385,0.177 10 false SST
*a Protective Tape


Place SST on the brake piston return spring and compress the brake piston return spring using a press.

SST
09387-00070  

NOTICE:

Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.



h.

Using a screwdriver, install the snap ring to the transaxle case as shown in the illustration.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case.

·

Be sure to align the opening of the snap ring with one of the protrusions on the brake piston return spring as shown in the illustration.


·

Be careful not to damage the transaxle case.



HINT:

Tape the screwdriver tip before use.



Hide 35782C 20.INSTALL COUNTER DRIVE GEAR

a.

Install 2 new balls of the counter drive gear bearing to the counter drive gear bearing.


b.
C274819N01
1.677,1.396 0.917,1.823 0.917,1.823 1.75,1.156 true 1.24,3.219 0.781,3.073 0.781,3.073 1.302,2.917 false 1.208,4.156 0.688,3.979 0.688,3.979 1.219,3.979 false 0.615,1.75 1.073,1.948 0.458,0.198 10 SST 0.469,3 0.927,3.198 0.458,0.198 10 SST 0.385,3.906 0.844,4.104 0.458,0.198 10 SST

Using SST, install the counter drive gear, a new bearing inner race (front side) and new bearing inner race (rear side) to the transaxle case.

SST
09223-15030  
09527-17011  
09950-70010  (09951-07100)
09950-60020  (09951-00810)

NOTICE:

There should not be any clearance between the bearing inner race (front side) and counter drive gear.



Hide 35720 21.INSTALL FRONT PLANETARY GEAR ASSEMBLY

a.
C274820N01
1.646,0.865 2.333,0.531 true 1.615,2.677 1.917,2.677 false 1.677,3.885 2,4.073 2,4.073 1.656,4.073 false 2.385,0.438 2.844,0.635 0.458,0.198 10 SST 1.969,2.604 2.427,2.802 0.458,0.198 10 SST 2.042,4.01 2.5,4.208 0.458,0.198 10 SST

Using SST and a press, press the front planetary gear assembly onto the transaxle case.

SST
09223-15030  
09527-17011  
09951-01100  


Hide 35622G 22.INSTALL NO. 2 BRAKE PISTON

a.
C136673C02
1.99,0.521 2.573,0.521 false 1.344,1.208 0.885,1.208 false 0.719,1.135 0.875,1.323 0.156,0.188 10 *1 2.615,0.438 2.771,0.625 0.156,0.188 10 *1
*1 O-ring


Coat 2 new O-rings with ATF and install them to the No. 2 brake piston.

NOTICE:

Ensure that the 2 O-rings are not twisted.



b.
C138726

Install the No. 2 brake piston to the transaxle case.

NOTICE:

Be careful not to damage the O-rings.



Hide 35068C 23.INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

a.

Install the 1st and reverse brake return spring sub-assembly to the transaxle case.


b.

Place SST on the 1st and reverse brake return spring sub-assembly and compress the 1st and reverse brake return spring sub-assembly using a press.

SST
09387-00060  

C281637C01
2.271,2.438 2.938,2.438 true 1.021,0.417 1.156,0.417 1.156,0.417 1.302,0.906 true 1.615,0.167 1.781,0.167 1.781,0.167 2.042,1.167 true 1.448,0.104 1.76,0.26 0.313,0.156 10 false *a 0.719,0.354 1.083,0.531 0.365,0.177 10 false SST 3,2.365 3.365,2.542 0.365,0.177 10 false SST
*a Protective Tape - -


NOTICE:

Stop the press when the 1st and reverse brake return spring sub-assembly is flush with the snap ring groove. This prevents the 1st and reverse brake return spring sub-assembly from being deformed.



c.

Using a screwdriver, install the snap ring to the transaxle case as shown in the illustration.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case.

·

Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case as shown in the illustration.


·

Be careful not to damage the transaxle case.



HINT:

Tape the screwdriver tip before use.



Hide 35682A 24.INSTALL NO. 2 BRAKE DISC

a.
C136483C02
1.313,0.875 1.208,0.875 1.208,0.875 1.208,1.698 false 1.208,1.698 1.313,1.698 false 1.313,1.073 1.208,1.073 false 1.323,1.479 1.208,1.479 false 1.313,1.271 1.104,1.271 false 2.167,0.542 2.302,0.542 false 2.208,0.781 2.365,0.781 2.365,0.781 2.365,1.594 false 2.365,1.594 2.208,1.594 false 2.208,0.99 2.365,0.99 false 2.208,1.406 2.365,1.406 false 2.208,1.188 2.448,1.188 false 2.51,1.104 2.677,1.281 0.167,0.177 10 *3 0.917,1.188 1.073,1.365 0.156,0.177 10 *2 2.354,0.458 2.521,0.635 0.167,0.177 10 *1
*1 No. 2 Brake Flange
*2 No. 2 Brake Plate
*3 No. 2 Brake Disc


Install the 5 No. 2 brake discs, 5 No. 2 brake plates and No. 2 brake flange to the transaxle case.

NOTICE:

Make sure that the discs, plates and flange are installed in the correct order.



b.
C281623C01
2.01,1.333 1.823,0.479 1.823,0.479 1.667,0.479 true 1.49,0.406 1.802,0.563 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring to the transaxle case.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case.

·

Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case as shown in the illustration.


·

Be careful not to damage the transaxle case.



HINT:

Tape the screwdriver tip before use.



Hide 35762E 26.INSTALL PLANETARY RING GEAR FLANGE

a.
C136480C03
1.271,0.646 0.969,0.646 false 0.948,2.292 1.208,2.292 false 2.094,1.333 2.406,1.333 false 0.771,2.219 0.948,2.385 0.177,0.167 10 *3 2.458,1.25 2.625,1.406 0.167,0.156 10 *2 0.771,0.573 0.948,0.74 0.177,0.167 10 *1
*1 Snap Ring
*2 Planetary Ring Gear Flange
*3 Planetary Ring Gear


Install the planetary ring gear flange to the planetary ring gear.


b.

Using a screwdriver, install the snap ring to the planetary ring gear.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the planetary ring gear.


·

Be careful not to damage the planetary ring gear.



HINT:

Tape the screwdriver tip before use.



Hide 35743K 27.INSTALL PLANETARY RING GEAR

a.
C299134C01
1.104,1.74 1.563,1.74 false 1.302,1.302 1.427,1.302 1.427,1.302 1.49,1.042 false 1.083,0.375 1.24,0.125 1.24,0.125 1.344,0.125 false 1.396,0.042 1.729,0.333 0.333,0.292 10 false *1 1.125,1.229 1.625,1.521 0.5,0.292 10 false *2 1.635,1.656 2.115,2 0.479,0.344 10 false *3
*1 One-way Clutch Assembly
*2 Outer Race Retainer
*3 Planetary Ring Gear


Install the outer race retainer to the one-way clutch assembly.


b.

Install the planetary ring gear to the one-way clutch assembly.

NOTICE:

Make sure that the one-way clutch assembly is positioned in the correct direction as shown in the illustration.



Hide 35790 28.INSTALL ONE-WAY CLUTCH ASSEMBLY

a.
C274822

Coat the thrust needle roller bearing with ATF, and install it onto the planetary gear assembly.

Bearing Diameter:
- Inside Outside
Bearing 56.1 mm (2.21 in.) 80.9 mm (3.19 in.)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.

Install the one-way clutch assembly to the transaxle case.

NOTICE:

Make sure that there is no clearance between the retainer and the claw on the one-way clutch assembly. If there is any clearance, the spring of the retainer will be deformed.



c.
C281622C01
2.24,1.24 2.073,0.458 2.073,0.458 1.938,0.458 true 1.771,0.365 2.083,0.521 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring to the transaxle case.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the transaxle case.

·

Be sure to align the opening of the snap ring with one of the protrusions on the transaxle case as shown in the illustration.


·

Be careful not to damage the transaxle case.



HINT:

Tape the screwdriver tip before use.



Hide 35557 29.INSTALL PARKING LOCK PAWL

a.
C136475C01
0.896,0.469 1.063,0.469 1.063,0.469 1.156,1.302 false 0.26,0.385 0.406,0.385 0.406,0.385 0.479,1.625 false 0.375,2.823 0.375,2.708 0.375,2.708 1.031,2.469 false 1.458,2.708 0.854,3.021 0.854,3.021 0.854,3.146 false 0.313,2.844 0.49,3.021 0.177,0.177 10 *3 0.792,3.167 0.958,3.333 0.167,0.167 10 *4 0.094,0.313 0.26,0.479 0.167,0.167 10 *1 0.729,0.385 0.906,0.531 0.177,0.146 10 *2
*1 Parking Lock Pawl Shaft
*2 Parking Lock Pawl
*3 Spring
*4 Parking Lock Pawl Pin


Install the parking lock pawl to the transaxle case with the parking lock pawl shaft.


b.

Install the parking lock pawl pin to the transaxle case.


c.
C137444

Install the spring to the parking lock pawl.

NOTICE:

Make sure that one end of the spring is set in the hole of the transaxle case and the other end is positioned on the parking lock pawl as shown in the illustration.



Hide 35598 30.INSTALL PARKING LOCK SLEEVE

a.
C136474

Install the parking lock sleeve to the transaxle case.


Hide 35596 31.INSTALL PAWL STOPPER PLATE

a.
C136473

Install the pawl stopper plate to the transaxle case with the 2 bolts.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)


Hide 35558 32.INSTALL PAWL SHAFT CLAMP

a.
C136472

Install the pawl shaft clamp to the transaxle case with the bolt.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)


Hide 35783R 33.INSTALL COUNTER DRIVEN GEAR

a.
C136469

Install the counter driven gear to the transaxle case.


Hide 35782H 34.INSTALL COUNTER DRIVE GEAR NUT

a.
C136700N02
1.5,4.042 1.656,4.219 0.156,0.177 10 P

Turn the manual valve lever 2 notches counterclockwise to set it to P as shown in the illustration.


b.
C136468N02
1.594,1.396 0.677,0.271 false 0.365,0.177 0.771,0.344 0.406,0.167 10 SST

Using SST, install a new counter drive gear nut.

SST
09387-00130  

Torque:
120 N*m (1224 kgf*cm, 89 ft.*lbf)


c.
C136699N02
1.521,3.979 1.76,4.146 0.24,0.167 10 N

Turn the manual valve lever 2 notches clockwise to set it to N as shown in the illustration.


d.
C138252N02
1.563,1.823 0.656,2.177 false 0.354,2.135 0.729,2.323 0.375,0.188 10 SST

Using SST and a torque wrench, measure the turning torque of the bearing while rotating SST at 60 rpm.

SST
09387-00130  

Turning torque:

0.1 to 0.2 N*m (1 to 2 kgf*cm, 0.9 to 1.9 in.*lbf)


If the measured value is not within the specified range, gradually tighten the nut until the turning torque falls within the specified range.

Maximum torque:

180 N*m (1835 kgf*cm, 133 ft.*lbf)



e.

Using a chisel and hammer, securely stake the counter drive gear nut.


Hide 35.INSPECT FRONT DIFFERENTIAL PINION BACKLASH

Hide 41311 36.INSTALL FRONT DIFFERENTIAL CASE

a.
C136467

Install the front differential case to the transaxle case.


Hide 35621F 37.INSTALL NO. 1 BRAKE PISTON

a.
C136466C02
1.979,0.656 2.375,0.656 false 1.354,0.677 0.906,0.677 false 2.417,0.573 2.563,0.729 0.146,0.156 10 *1 0.708,0.573 0.865,0.729 0.156,0.156 10 *1
*1 O-ring


Coat 2 new O-rings with ATF and install them to the No. 1 brake piston.

NOTICE:

Ensure that the O-rings are not twisted.



b.
C138253

Install the No. 1 brake piston to the oil pump assembly.

NOTICE:

Be careful not to damage the O-rings.



Hide 35608L 38.INSTALL 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

a.
C136464

Install the 3 2nd brake piston return springs to the oil pump assembly.

NOTICE:

Make sure that the 3 2nd brake piston return springs are installed onto the protrusions on the oil pump assembly.



Hide 39.INSTALL NO. 1 BRAKE DISC

a.
C293936C01
1.615,0.24 1.76,0.24 1.76,0.24 2.031,0.49 false 1.417,1.219 1.917,1.219 false 1.781,1.698 1.927,1.698 false 1.771,1.229 1.781,2.635 false 1.781,2.146 1.927,2.146 false 1.781,2.635 1.938,2.635 false 2.771,0.958 2.958,0.958 false 2.771,1.417 3.073,1.417 false 2.75,2.344 2.938,2.344 false 2.958,2.344 2.948,0.958 false 2.75,1.885 2.958,1.885 false 1.354,0.177 1.667,0.333 0.313,0.156 10 false *1 1.229,1.146 1.542,1.302 0.313,0.156 10 false *2 3.115,1.344 3.427,1.5 0.313,0.156 10 false *3
*1 No. 1 Brake Flange
*2 No. 1 Brake Plate
*3 No. 1 Brake Disc


Install the 4 No. 1 brake discs, 4 No. 1 brake plates and No. 1 brake flange to the oil pump assembly.

NOTICE:
·

Make sure that the discs, plates, and flange are installed in the correct order.

·

Be sure to install the flange in the correct direction.




b.

Place SST on the flange and compress the flange using a press.

SST
09387-00070  
09495-65040  

NOTICE:

Stop the press when the brake piston return spring is flush with the snap ring groove. This prevents the brake piston return spring from being deformed.



c.
C281624C01
0.5,3.188 0.969,3.188 false 1.906,0.781 2.438,0.177 2.438,0.177 2.156,1.01 true 2.438,0.177 2.563,0.177 false 2.375,1.271 2.667,0.438 2.667,0.438 2.813,0.438 true 2.635,0.094 2.948,0.25 0.313,0.156 10 false SST 0.198,3.104 0.531,3.323 0.333,0.219 10 false (#1) 2.865,0.344 3.177,0.5 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring to the oil pump assembly as shown in the illustration (#1).

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the oil pump.

·

Make sure to align the protruding part of the snap ring with the indented part (#1) of the oil pump assembly shown in the illustration to install the snap ring.


·

Be careful not to damage the oil pump assembly.



HINT:

Tape the screwdriver tip before use.



d.
C176220

Install the brake snap ring stopper to the oil pump assembly.

NOTICE:

Be sure to install the brake snap ring stopper in the correct direction.



e.
C281625C01
2.552,3.365 2.813,3.365 false 1.938,0.771 2.49,0.25 2.49,0.25 2.167,1.01 true 2.385,1.271 2.677,0.521 2.677,0.521 2.823,0.521 true 2.875,0.427 3.188,0.583 0.313,0.156 10 false *a 2.875,3.271 3.208,3.479 0.333,0.208 10 false (#2) 2.552,0.156 2.865,0.313 0.313,0.156 10 false SST
*a Protective Tape


Using a screwdriver, install the snap ring to the oil pump assembly as shown in the illustration (#2).

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the oil pump assembly.

·

Make sure to align the protruding part of the snap ring with the indented part (#2) of the oil pump assembly shown in the illustration to install the snap ring.


·

Be careful not to damage the oil pump assembly.



HINT:

Tape the screwdriver tip before use.



f.
C153481C02
1.656,2.146 1.281,2.677 1.281,2.677 1.146,2.677 false 1.49,1.771 1.49,0.594 1.49,0.594 1.917,0.594 false 1.75,1.76 1.75,0.594 false 0.969,2.615 1.156,2.781 0.188,0.167 10 *2 1.979,0.521 2.156,0.688 0.177,0.167 10 *1 0.104,0.083 0.292,0.24 0.188,0.156 10 *a
*1 Snap Ring
*2 Brake Snap Ring Stopper
*a Correctly installed


Check that the brake snap ring stopper can be turned by hand.

NOTICE:

If the brake snap ring stopper cannot be turned by hand, the brake snap ring stopper may have been installed upside down, or the snap ring may not have been completely located in the groove on the oil pump. Remove and reinstall the snap ring and the brake snap ring stopper.



Hide 34321 41.INSTALL UNDERDRIVE PLANETARY SUN GEAR

a.
C141538C01
1.594,0.563 1.292,0.563 false 2.521,1.292 2.219,1.292 false 1.115,0.479 1.271,0.667 0.156,0.188 10 *2 2.573,1.208 2.729,1.396 0.156,0.188 10 *1
*1 Thrust Needle Roller Bearing
*2 Underdrive Planetary Sun Gear


Coat the thrust needle roller bearing with ATF, and install it to the oil pump assembly.

Bearing Diameter:
- Inside Outside
Bearing 57.7 mm (2.27 in.) 75.2 mm (2.96 in.)

NOTICE:

Be sure to install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.

Install the underdrive planetary sun gear to the oil pump assembly.


Hide 35701 42.INSTALL INPUT SHAFT SUB-ASSEMBLY

a.
C141539C02
1.677,2.823 2.188,2.667 2.188,2.667 1.688,3.135 false 1.698,2.99 2.188,2.667 false 0.688,0.469 2.167,0.125 2.167,0.125 1.75,0.438 true 0.833,0.802 0.604,1.417 0.604,1.417 1.313,1.031 true 1.677,1.781 2.146,1.781 false 2.198,2.573 2.385,2.76 0.188,0.188 10 *3 2.198,0.042 2.375,0.24 0.177,0.198 10 *1 0.479,1.458 0.667,1.656 0.188,0.198 10 *2 2.188,1.677 2.365,1.865 0.177,0.188 10 *4
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing
*3 Input Shaft Oil Seal Ring
*4 Input Shaft Sub-assembly


Coat 3 new input shaft oil seal rings with ATF and install them to the input shaft sub-assembly.

NOTICE:

Do not expand the gap of the oil seal ring excessively.



b.

Coat the thrust needle roller bearing and thrust needle roller race with ATF, and install them on the oil pump assembly.

Bearing and Race Diameter:
- Inside Outside
Bearing 29.1 mm (1.15 in.) 48.6 mm (1.91 in.)
Race 30.7 mm (1.21 in.) 48.3 mm (1.90 in.)

NOTICE:

Be sure to install the thrust needle roller bearing in the correct direction.



c.
C136459

Install the input shaft sub-assembly to the oil pump assembly.


Hide 35706V 43.INSTALL PLANETARY SUN GEAR SUB-ASSEMBLY

a.
C136457C02
1.427,2.938 1.094,2.938 false 1.229,0.458 1.396,0.458 false 2.5,1.719 2.208,1.719 false 0.917,2.875 1.094,3.021 0.177,0.146 10 *3 1.042,0.396 1.208,0.542 0.167,0.146 10 *1 2.552,1.646 2.74,1.802 0.188,0.156 10 *2
*1 Planetary Sun Gear Sub-assembly
*2 Underdrive Planetary Gear Assembly
*3 Snap Ring


Using a snap ring expander, install the snap ring to the underdrive planetary gear assembly.


b.

Using a snap ring expander, install the planetary sun gear sub-assembly to the underdrive planetary gear assembly with the snap ring expanded.


Hide 34341 44.INSTALL UNDERDRIVE PLANETARY RING GEAR

a.
C136456C02
2.083,0.438 2.365,0.438 false 1.323,0.802 1,0.802 false 2.406,0.354 2.563,0.542 0.156,0.188 10 *1 0.823,0.729 0.99,0.896 0.167,0.167 10 *2
*1 Snap Ring
*2 Underdrive Planetary Ring Gear


Install the underdrive planetary ring gear to the underdrive planetary gear assembly.


b.

Using needle-nose pliers, install the snap ring to the underdrive planetary ring gear.

NOTICE:

Confirm that the snap ring is correctly located in the groove of the underdrive planetary ring gear.



Hide 35663 45.INSTALL NO. 3 BRAKE HUB

a.
C202906C01
1.146,0.208 1.271,0.208 1.271,0.208 1.469,0.344 false 1.188,1.115 1.271,1.115 1.271,1.115 1.469,0.948 false 1.01,0.125 1.188,0.292 0.177,0.167 10 false *1 1.031,1.052 1.271,1.365 0.24,0.313 10 false *2
*1 Thrust Needle Roller Race
*2 Thrust Needle Roller Bearing


Coat the thrust needle roller bearing and thrust needle roller race with ATF and install them to the underdrive planetary gear assembly.

Thrust Needle Roller Bearing and Thrust Needle Roller Race Diameter:
- Inside Outside
Thrust needle roller bearing 62.6 mm (2.46 in.) 82.9 mm (3.26 in.)
Thrust needle roller race 65.9 mm (2.59 in.) 80.3 mm (3.16 in.)

NOTICE:

Be sure to install the thrust needle roller bearing so that the temper colored side of the race is visible.



b.
C136454

Install the No. 3 brake hub to the underdrive planetary gear assembly.


Hide 34330 46.INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY

a.
C136458

Install the underdrive planetary gear assembly to the oil pump assembly.


Hide 35683B 47.INSTALL NO. 3 BRAKE DISC

a.
C136452C03
2.135,0.406 2.323,0.406 false 2.146,1.25 2.292,1.25 false 2.146,0.719 2.229,0.719 2.229,0.719 2.229,1.635 false 2.229,1.635 2.146,1.635 false 1.177,1.979 1.323,1.979 false 1.313,0.948 1.125,0.948 false 1.313,1.448 1.229,1.448 1.229,1.448 1.229,0.948 false 2.385,0.333 2.552,0.521 0.167,0.188 10 *1 2.375,1.167 2.542,1.344 0.167,0.177 10 *3 0.938,0.865 1.115,1.042 0.177,0.177 10 *2 1.021,1.906 1.188,2.094 0.167,0.188 10 *1
*1 No. 3 Brake Flange
*2 No. 3 Brake Plate
*3 No. 3 Brake Disc


Install the 2 No. 3 brake flanges, 3 No. 3 brake discs and 2 No. 3 brake plates to the oil pump assembly.

NOTICE:

Make sure that the discs, plates and flanges are installed in the correct order.



b.
C274824N03
1.375,0.469 2.667,0.323 2.667,0.323 2.25,0.833 true 2.708,0.219 3.167,0.417 0.458,0.198 10 (A)

Using a screwdriver, install the snap ring to the oil pump assembly.

NOTICE:
·

Confirm that the snap ring is correctly located in the groove of the oil pump assembly.

·

Make sure that the snap ring ends are positioned as shown in the illustration (A).


·

Be careful not to damage the oil pump assembly.



HINT:

Tape the screwdriver tip before use.



Hide 49.INSTALL FRONT OIL PUMP BODY O-RING

a.
C293910

Coat a new O-ring with ATF and install it to the front oil pump body sub-assembly.


Hide 50.INSTALL OIL PUMP ASSEMBLY

a.
C293909C05
2.135,1.25 2.521,1.25 false 0.969,0.542 1.354,0.542 false 0.771,0.438 1.083,0.635 0.313,0.198 10 false *1 2.563,1.146 2.875,1.344 0.313,0.198 10 false *2
*1 Thrust Needle Roller Bearing
*2 O-ring


Coat a new O-ring with ATF and install it to the transaxle case.


b.

Coat the thrust needle roller bearing with ATF.


c.

Install the thrust needle roller bearing to the counter drive gear nut.

Thrust Needle Roller Bearing Diameter:
- Inside Outside
Thrust needle roller bearing 53.1 mm (2.09 in.) 79 mm (3.11 in.)

NOTICE:

Be sure to install the thrust needle roller bearing so that the temper colored side of the race is visible.



d.

Coat the thrust needle roller race with MP grease.


e.
C293908C06
0.302,2.75 0.615,2.75 false 0.094,2.667 0.292,2.865 0.198,0.198 10 false *1
*1 Thrust Needle Roller Race


Install the thrust needle roller race to the underdrive planetary gear assembly.

Thrust Needle Roller Race Diameter:
- Inside Outside
Thrust needle roller race 59.4 mm (2.34 in.) 77 mm (3.03 in.)


f.
C296578C01
2.344,0.188 2.729,0.188 false 2.771,0.094 3.083,0.292 0.313,0.198 10 false *1
*1 Gasket


Coat a new gasket with ATF and install it to the oil pump assembly.


g.

Install the oil pump assembly to the transaxle case with the 7 bolts.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)


Hide 35882A 51.INSTALL DIFFERENTIAL GEAR LUBE APPLY TUBE

a.
C274811

Install the differential gear lube apply tube to the transaxle housing.

NOTICE:

Insert the differential gear lube apply tube into the transaxle case until it makes contact with the stopper.



b.

Install the clamp to the differential gear lube apply tube with the bolt.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)

NOTICE:

There should be clearance between the differential lube apply tube and clamp.



Hide 35111C 52.INSTALL TRANSAXLE HOUSING

a.

Clean and degrease the contact surfaces between the transaxle housing and transaxle case.

NOTICE:

Make sure that there is no ATF on the contact surfaces.



b.
C138263C01
2.707,0.175 2.862,0.334 0.155,0.159 10 *a 2.665,0.25 2.397,0.474 false
*a Seal Packing


Apply seal packing to the transaxle case.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.


·

After applying seal packing, install the transaxle housing to the transaxle case within 3 minutes and tighten the bolts within 10 minutes.




c.
C278983

Install the transaxle housing to the transaxle case with the 17 bolts.

Torque:
30.6 N*m (312 kgf*cm, 23 ft.*lbf)


d.
C285154

Clean and degrease the 3 bolts and the installation holes in the transaxle case.


e.

Apply adhesive to 2 or 3 threads on the ends of the 3 bolts.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



f.

Install the 3 bolts.

Torque:
22.7 N*m (231 kgf*cm, 17 ft.*lbf)


Hide 53.INSTALL NO. 1 CLUTCH DISC

a.
C136446C02
2.125,0.604 2.281,0.604 2.281,0.604 2.281,1.781 false 2.281,1.781 2.125,1.781 false 1.354,1.198 1.115,1.198 false 2.125,0.99 2.281,0.99 false 2.125,1.375 2.385,1.375 false 2.104,0.313 2.26,0.313 false 1.344,0.781 1.198,0.781 1.198,0.781 1.198,1.99 false 1.198,1.99 1.344,1.99 false 1.344,1.552 1.198,1.552 false 2.313,0.24 2.469,0.438 0.156,0.198 10 *1 2.438,1.302 2.604,1.5 0.167,0.198 10 *3 0.917,1.125 1.094,1.333 0.177,0.208 10 *2
*1 No. 1 Clutch Flange
*2 No. 1 Clutch Plate
*3 No. 1 Clutch Disc


Install the No. 1 clutch flange, 4 No. 1 clutch discs and 4 No. 1 clutch plates to the direct multiple disc clutch assembly.

NOTICE:

Make sure that the flange, discs and plates are installed in the correct order.



b.
C136445

Using a screwdriver, install the 2 snap rings to the direct multiple disc clutch assembly.

NOTICE:
·

Confirm that the snap rings are correctly located in the groove of the direct multiple disc clutch assembly.


·

Be careful not to damage the direct multiple disc clutch assembly.



HINT:

Tape the screwdriver tip before use.



Hide 35730 55.INSTALL REAR PLANETARY SUN GEAR ASSEMBLY

a.
C141542C01
1.281,0.823 0.854,0.563 false 1.26,1.469 0.854,1.604 false 0.667,0.479 0.844,0.646 0.177,0.167 10 *1 0.688,1.552 0.865,1.74 0.177,0.188 10 *2
*1 Thrust Needle Roller Bearing
*2 Thrust Needle Roller Race


Coat the thrust needle roller bearing and thrust needle roller race with ATF, and install them to the direct multiple disc clutch assembly.

Bearing and Race Diameter:
- Inside Outside
Bearing 28 mm (1.10 in.) 47.1 mm (1.85 in.)
Race 26.1 mm (1.03 in.) 44 mm (1.73 in.)

NOTICE:

Install the thrust needle roller bearing properly so that the temper colored side of the race will be visible.



b.
C136437

Install the rear planetary sun gear assembly to the direct multiple disc clutch assembly.


c.
C136436

Using a snap ring expander, install the snap ring to the direct multiple disc clutch assembly.


Hide 56.INSTALL NO. 2 CLUTCH DISC

a.
C136435C02
2.135,1.708 2.292,1.708 false 2.125,0.688 2.25,0.688 2.25,0.688 2.25,1.49 false 2.25,1.49 2.125,1.49 false 2.115,1.073 2.323,1.073 false 1.354,0.458 1.188,0.458 1.188,0.458 1.188,1.271 false 1.188,1.271 1.344,1.271 false 1.344,0.896 1.052,0.896 false 2.333,1.646 2.5,1.833 0.167,0.188 10 *3 2.354,1 2.531,1.188 0.177,0.188 10 *2 0.865,0.833 1.031,1.021 0.167,0.188 10 *1
*1 No. 2 Clutch Plate
*2 No. 2 Clutch Disc
*3 No. 2 Clutch Flange


Install the No. 2 clutch flange, 3 No. 2 clutch discs and 3 No. 2 clutch plates to the direct multiple disc clutch assembly.

NOTICE:

Make sure that the flange, discs and plates are installed in the correct order.



Hide 35635E 57.INSTALL DIRECT MULTIPLE DISC CLUTCH SNAP RING

a.
C136428C02
1.625,0.25 1.292,0.25 false 1.635,1.927 1.448,1.75 1.448,1.75 1.229,1.75 false 1.104,0.177 1.271,0.354 0.167,0.177 10 *2 1.063,1.677 1.219,1.823 0.156,0.146 10 *1
*1 Intermediate Shaft Oil Seal
*2 O-ring


Coat a new O-ring with ATF and install it to the direct multiple disc clutch assembly.


b.

Coat a new intermediate shaft oil seal with ATF and install it to the direct multiple disc clutch assembly.


c.
C141535

Install the No. 2 direct clutch piston to the direct multiple disc clutch assembly.

NOTICE:

Be sure to engage the claws on the direct multiple disc clutch assembly in the grooves on the No. 2 direct clutch piston.



d.
C281636C01
2.417,1.24 2.552,0.844 2.552,0.844 2.677,0.844 false 2.729,0.75 3.042,0.906 0.313,0.156 10 false *a
*a Protective Tape


Using a screwdriver, install the snap ring to the direct multiple disc clutch assembly.

NOTICE:
·

Position the opening of the snap ring as shown in the illustration.

·

Confirm that the snap ring is correctly located in the groove of the direct multiple disc clutch assembly.


·

Be careful not to damage the direct multiple disc clutch assembly.



HINT:

Tape the screwdriver tip before use.



Hide 35635C 59.INSTALL DIRECT MULTIPLE DISC CLUTCH ASSEMBLY

a.
C141543C01
1.844,1.271 2.344,1.271 false 0.563,2.354 1.052,2.354 false 2.385,1.198 2.542,1.344 0.156,0.146 10 *2 0.385,2.281 0.552,2.438 0.167,0.156 10 *1
*1 Thrust Needle Roller Bearing
*2 Direct Multiple Disc Clutch Assembly


Coat the thrust needle roller bearing with ATF and install it on the transaxle case.

Bearing Diameter:
- Inside Outside
Bearing 61.2 mm (2.41 in.) 79 mm (3.11 in.)


b.

Install the direct multiple disc clutch assembly to the transaxle case.


c.

Clean the contact surfaces of the transaxle case and rear transaxle cover sub-assembly.


d.
C138269C01
2.917,0.729 3.063,0.906 0.146,0.177 10 *a
*a Dimension A


As shown in the illustration, place a straightedge on the multiple direct clutch drum and measure the distance between the transaxle case and the straightedge using a vernier caliper (Dimension A).


e.
C138268C02
0.604,0.813 0.771,0.99 0.167,0.177 10 *a
*a Dimension B


Using a vernier caliper and a straightedge, measure the distance shown in the illustration (Dimension B).


f.

Calculate the end play value using the following formula:

End play = Dimension B - Dimension A - Thrust needle roller bearing thickness

End play:

0.007 to 1.113 mm (0.000276 to 0.0438 in.)



Hide 35102 60.INSTALL REAR TRANSAXLE COVER SUB-ASSEMBLY

a.
C194898N01
2.594,0.854 2.74,0.854 2.74,0.854 2.635,1.042 false 1.188,1.354 0.958,1.396 0.958,1.396 1.188,1.198 false 2.792,0.792 3.146,0.958 0.354,0.167 10 SST 0.656,1.323 0.969,1.49 0.313,0.167 10 SST

Using SST and a hammer, install a new needle roller bearing into the rear transaxle cover sub-assembly.

SST
09950-60010  (09951-00220)
09950-70010  (09951-07100)

Installation depth:

21.5 to 21.9 mm (0.847 to 0862 in.)



b.

Clean and degrease the 2 "TORX" screws and the installation holes in the rear transaxle cover sub-assembly.


c.

Apply adhesive to 2 or 3 threads on the ends of the 2 "TORX" screws.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



d.
C274808

Using a T30 "TORX" socket wrench, install the rear transaxle cover plate to the rear transaxle cover sub-assembly with the 2 "TORX" screws.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


e.
C299131C08
1.365,0.5 1.469,0.5 1.469,0.5 1.719,0.823 true 1.958,1.302 2.219,1.823 2.219,1.823 2.083,1.823 true 1.188,0.417 1.51,0.688 0.323,0.271 10 false *1 1.906,1.75 2.229,2.021 0.323,0.271 10 false *1
*1 Oil Seal Ring


Coat 2 new oil seal rings with ATF and install them to the rear transaxle cover sub-assembly.

NOTICE:

Confirm that the 2 oil seal rings are correctly located in the grooves of the rear transaxle cover sub-assembly.



f.
C297890C08
1.063,1.292 0.74,0.521 0.74,0.521 0.604,0.521 false 0.729,1.542 0.542,1.115 0.542,1.115 0.406,1.115 false 0.438,0.448 0.771,0.719 0.333,0.271 10 false *1 0.219,1.042 0.5,1.406 0.281,0.365 10 false *2 2.167,1.885 2.5,2.156 0.333,0.271 10 false *1 1.792,1.885 2.073,2.25 0.281,0.365 10 false *2
*1 Thrust Needle Roller Bearing
*2 Thrust Needle Roller Race


Coat the thrust needle roller bearing and thrust needle roller race with MP grease and install them on the rear transaxle cover sub-assembly.

Thrust Needle Roller Bearing and Thrust Needle Roller Race Diameter:
- Inside Outside
Thrust needle roller bearing 48.9 mm (1.93 in.) 72.0 mm (2.84 in.)
Thrust needle roller race 52.2 mm (2.06 in.) 70.4 mm (2.77 in.)


g.
C274807

Coat 3 new O-rings with ATF and install them to the transaxle case.

NOTICE:

Ensure that the O-rings are not twisted.



h.

Remove packing material from the contact surfaces between the rear transaxle cover sub-assembly and transaxle case.

NOTICE:

Make sure that there is no ATF on the contact surfaces.



i.
C138271C01
1.24,0.615 1.073,0.188 1.073,0.188 0.938,0.188 true 0.781,0.094 1.094,0.292 0.313,0.198 10 *a
*a Seal Packing


Apply seal packing to the transaxle case.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


NOTICE:
·

Apply seal packing in a continuous line (width 1.2 mm (0.0472 in.)) along the sealing surface.


·

After applying seal packing, install the rear transaxle cover sub-assembly to the transaxle case within 3 minutes and tighten the bolts within 10 minutes.




j.
C285155

Install the rear transaxle cover sub-assembly to the transaxle case with the 12 bolts.

Torque:
for bolt A : 22.7 N*m (231 kgf*cm, 17 ft.*lbf)


k.
C285156

Clean and degrease the 2 bolts and the installation holes in the transaxle case.


l.

Apply adhesive to 2 or 3 threads on the ends of the 2 bolts labeled B.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



m.

Install the 2 bolts.

Torque:
for bolt B : 16.9 N*m (172 kgf*cm, 12 ft.*lbf)


n.
C162439

Install a new gasket to the refill plug.


o.

Install the refill plug to the rear transaxle cover sub-assembly.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)


Hide 35145C 62.INSTALL TRANSAXLE CASE GASKET

a.
C274805

Coat 2 new gaskets with ATF and install them to the transaxle case.


Hide 35410 63.INSTALL TRANSMISSION VALVE BODY ASSEMBLY

a.

Coat the O-ring of the transmission wire with ATF.


b.
C326386C04
0.906,1 1.052,0.76 1.052,0.76 0.896,0.76 true 1.156,0.917 1.573,0.594 1.573,0.594 1.302,0.594 true 0.729,0.698 0.917,0.844 0.188,0.146 10 true *1 1.125,0.521 1.313,0.667 0.188,0.146 10 true *2 3.177,2.948 3.365,3.115 0.188,0.167 10 true *a 3.042,2.948 3.177,3.104 0.135,0.156 10 true B 2.208,3.969 2.344,4.125 0.135,0.156 10 true B 1.969,3.969 2.104,4.125 0.135,0.156 10 true B 1.594,3.917 1.729,4.073 0.135,0.156 10 true B 1.104,3.958 1.24,4.115 0.135,0.156 10 true B 0.583,4.083 0.729,4.25 0.146,0.167 10 true B 0.177,3.583 0.365,3.75 0.188,0.167 10 true *a 0.052,3.583 0.188,3.74 0.135,0.156 10 false E 0.063,2.677 0.146,2.813 0.083,0.135 10 true D 0.479,2.031 0.594,2.167 0.115,0.135 10 true C 1.25,1.979 1.365,2.115 0.115,0.135 10 true B 1.948,1.99 2.063,2.125 0.115,0.135 10 true A
*1 Manual Valve Lever Shaft Sub-assembly Pin
*2 Manual Valve
*a Positioning Bolt


Insert the manual valve lever shaft sub-assembly pin into the groove on the end of the manual valve as shown in the illustration and temporarily install the transmission valve body assembly to the transaxle case with the 11 bolts.

Item Bolt Length
Bolt A 25 mm (0.984 in.)
Bolt B 30 mm (1.18 in.)
Bolt C 35 mm (1.38 in.)
Bolt D 45 mm (1.77 in.)
Bolt E 55 mm (2.17 in.)

NOTICE:
·

When installing the transmission valve body assembly, be careful not to allow the transmission revolution sensor and transaxle case to interfere with each other.

·

Be sure to insert the manual valve lever shaft sub-assembly pin into the groove on the end of the manual valve.




c.

Tighten the 2 positioning bolts shown in the illustration.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


d.

Tighten the 9 bolts to install the transmission valve body assembly.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


Hide 35330 64.INSTALL VALVE BODY OIL STRAINER ASSEMBLY

a.
C136688C03
1.833,0.406 2.073,0.406 false 2.115,0.323 2.292,0.5 0.177,0.177 10 *1
*1 O-ring


Coat a new O-ring with ATF and install it to the valve body oil strainer assembly.

NOTICE:

Ensure that the O-ring is not twisted or pinched.



b.
C136687

Install the valve body oil strainer assembly to the transmission valve body assembly with the 2 bolts.

Torque:
10.8 N*m (110 kgf*cm, 8 ft.*lbf)


Hide 35106D 65.INSTALL AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY

a.
C134963C04
2.656,0.208 1.865,0.208 1.865,0.208 1.865,1.438 false 2.438,0.99 2.438,0.208 false 2.729,0.146 2.906,0.313 0.177,0.167 10 *1
*1 Transmission Oil Cleaner Magnet


Install the 2 transmission oil cleaner magnets in the automatic transaxle oil pan sub-assembly.


b.

Install a new gasket to the automatic transaxle oil pan sub-assembly.


c.
C279450

Install the automatic transaxle oil pan sub-assembly to the automatic transaxle assembly with the 17 bolts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.
C279451

Clean and degrease the bolt and the installation hole in the automatic transaxle.


e.

Apply adhesive to the bolt.

Adhesive:

Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent



f.

Install the bolt.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)

NOTICE:
·

In order to ensure proper sealing of the transmission oil pan bolts, apply adhesive to the bolts and install them within 10 minutes of adhesive application.

·

Completely remove any oil or grease from the contact surface of the transaxle case and automatic transaxle oil pan sub-assembly with the gasket before installation.




g.
C206508

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the automatic transaxle assembly.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


h.
C279452

Using a 6 mm hexagon socket wrench, install the overflow plug and a new gasket to the automatic transaxle oil pan sub-assembly.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 35104Q 66.INSTALL TRANSAXLE CASE PLUG

a.

Install 3 new gaskets to the 3 hexagon bolts.


b.

Apply adhesive to the 3 hexagon bolts.

Adhesive:

Toyota Genuine Seal Packing 1344, Three Bond 1344 or equivalent


NOTICE:

In order to ensure proper sealing of the hexagon bolts, apply adhesive to the bolts and install them within 10 minutes of adhesive application.



c.
C134959

Using a 6 mm hexagon socket wrench, install the 3 hexagon bolts to the transaxle housing with the gaskets.

Torque:
17 N*m (173 kgf*cm, 13 ft.*lbf)


d.
C278538

Coat 6 new O-rings with ATF and install them to the 6 transaxle case plugs.


e.

Install the 6 transaxle case plugs to the transaxle case and rear transaxle cover sub-assembly.

Torque:
7.4 N*m (75 kgf*cm, 65 in.*lbf)


Hide 32921P 67.INSTALL OIL COOLER TUBE UNION

a.
C278537

Coat 2 new O-rings with ATF and install them to the 2 oil cooler tube unions.


b.

Using a 19 mm union nut wrench, install the 2 oil cooler tube unions as shown in the illustration.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 84540 68.INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

a.
C136686

Temporarily install the park/neutral position switch assembly to the transaxle case with the 2 bolts.

NOTICE:

Before installing the park/neutral position switch assembly, remove any dirt or rust on the manual valve lever shaft sub-assembly. Be sure to install the switch straight along the shaft while being careful not to deform the plate spring that supports the shaft. If the plate spring is deformed, the park/neutral position switch assembly cannot be reinstalled correctly.



b.

Temporarily install the control shaft lever.


c.
C206496N01
3.082,1.537 3.222,1.716 0.14,0.18 10 P 2.968,0.986 3.108,1.166 0.14,0.18 10 R 2.808,0.633 2.948,0.813 0.14,0.18 10 N

Turn the lever clockwise until it stops, and then turn it counterclockwise 2 notches.


d.

Remove the control shaft lever.


e.
C135733C05
1.688,1.313 2.49,0.729 2.49,0.729 1.688,1.438 false 2.521,0.625 2.708,0.781 0.188,0.156 10 *a
*a Protrusion


Align the protrusions of the park/neutral position switch assembly as shown in the illustration.


f.

Hold the switch in that position and tighten the 2 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)

NOTICE:

After installing the park/neutral position switch assembly, confirm that the 2 protrusions on the park/neutral position switch assembly are aligned.



g.
C136685

Install the control shaft lever to the control shaft with the washer and nut.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


Hide 35012B 69.INSTALL TRANSMISSION BREATHER HOSE SUB-ASSEMBLY

a.
C190664C01
1.354,0.219 1.219,0.219 1.219,0.219 1.135,0.458 false 2.188,1.344 2.052,1.344 2.052,1.344 1.969,1.583 false 2.667,1.313 2.531,1.313 2.531,1.313 2.448,1.552 false 1.396,0.135 1.708,0.333 0.313,0.198 10 *1 2.24,1.25 2.552,1.448 0.313,0.198 10 *2 2.708,1.229 3.021,1.427 0.313,0.198 10 *3
*1 Breather Plug Hose
*2 Breather Plug
*3 O-ring


Coat a new O-ring with ATF and install it to the breather plug.


b.

Install the breather plug to the breather plug hose.


c.
C206503

Install the transmission breather hose sub-assembly to the transaxle case.