Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY(for Power Seat) › 2012.12–2016.08
RM3090E _58 Vehicle Interior _008433 SEAT _0049774 FRONT SEAT ASSEMBLY(for Power Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Power Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 82192 1.INSTALL FRONT SEAT WIRE LH

a.
B340397

Attach the 6 clamps to install the front seat wire LH.


b.

Connect the 3 connectors.


Hide 71849C 2.INSTALL SEAT ADJUSTER COVER CAP

a.

Install the 2 seat adjuster cover caps to the separate type front seat cushion spring assembly LH.


Hide 71537D 3.INSTALL FRONT OUTER SEAT CUSHION EDGE PROTECTOR LH

a.
B341217

Install the front outer seat cushion edge protector LH in the direction indicated by the arrow in the illustration.


Hide 71538B 4.INSTALL FRONT INNER SEAT CUSHION EDGE PROTECTOR LH

HINT:

Use the same procedure described for the front outer seat cushion edge protector LH.


Hide 71874 5.INSTALL FRONT LOWER SEAT CUSHION SHIELD LH

a.

Attach the clamp to install the front lower seat cushion shield LH.


b.
B341216

Attach the hook in the direction indicated by the arrow in the illustration.


c.

Install the screw.


Hide 71873 6.INSTALL FRONT LOWER SEAT CUSHION SHIELD RH

HINT:

Use the same procedure described for the front lower seat cushion shield LH.


Hide 73240 7.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

a.
B340468

Install the front seat inner belt assembly LH with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.

Attach the 2 clamps.


c.
B340396C01
1.917,0.5 3,0.5 true 0.313,0.583 1.063,0.583 true 1.917,0.667 3,0.667 true 3.021,0.594 3.333,0.75 0.313,0.156 10 *1 3.021,0.417 3.333,0.573 0.313,0.156 10 *2 0.167,0.51 0.479,0.667 0.313,0.156 10 *1
*1 Wire Harness Clamp
*2 Connector Clamp


Attach the 2 wire harness clamps and connector clamp.


Hide 89178A 8.INSTALL SEAT POSITION AIRBAG SENSOR (w/ Occupant Classification System)

Hide 87510L 9.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71072S 10.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

a.

Set the separate type front seat cushion cover in place.


b.

Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 21 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seat cushion cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.



HINT:

Install the hog rings at the cutouts if they are there.


B340469C01
0.854,3.542 0.813,3.063 true 1.781,3.24 1.604,2.833 false 1.458,2.708 1.771,2.865 0.313,0.156 10 *1 0.792,3.542 1.104,3.698 0.313,0.156 10 *a
*1 Hog Ring Pliers - -
*a Cutout - -



Hide 11.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD

a.

Attach the 9 hooks to install the separate type front seat cushion cover with pad.

B343096


b.
B340395C01
1.917,0.667 0.75,0.25 true 0.771,0.708 1.521,0.708 true 0.75,1.281 1.583,1.281 true 0.75,1.698 1.583,1.698 true 0.604,0.604 0.917,0.76 0.313,0.156 10 false *1 0.583,1.188 0.896,1.344 0.313,0.156 10 false *1 0.583,1.604 0.896,1.76 0.313,0.156 10 false *1 0.573,0.135 0.885,0.292 0.313,0.156 10 false *2
*1 Wire Harness Clamp
*2 Connector Clamp


w/ Seat Heater System:

i.

Attach the 3 wire harness clamps and connector clamp to connect the seat cushion heater wire.


ii.

Connect the connector.



Hide 8219B 12.INSTALL FRONT NO. 2 SEAT WIRE LH

B340394

a.

Attach the 2 clamps to install the front No. 2 seat wire LH.


b.

Connect the 2 connectors.


Hide 73920A 13.INSTALL FRONT SEAT AIRBAG ASSEMBLY LH (w/ Front Seat Side Airbag)

Hide 79977A 14.INSTALL SEATBACK FELT

a.

Install the seatback felt to the separate type front seatback spring assembly LH.


Hide 71552S 15.INSTALL SEPARATE TYPE FRONT SEATBACK PAD

a.

Install the separate type front seatback pad to the separate type front seatback spring assembly LH.


Hide 87510N 16.INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71074S 17.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.

Set the separate type front seatback cover in place.


b.
B340470C01
0.521,3.833 0.656,3.219 true 1.563,3.885 1.979,3.469 false 2,3.333 2.313,3.49 0.313,0.156 10 *1 0.458,3.833 0.771,3.99 0.313,0.156 10 *a
*1 Hog Ring Pliers
*a Cutout


Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 8 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.



HINT:

Install the hog rings at the cutouts if they are there.



c.

w/ Front Seat Side Airbag:

i.

Pass the separate type front seatback cover bracket through the separate type front seatback pad.


ii.

for Single Type:

Install the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


iii.

for Dual Type:

Install the 2 nuts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)



d.

Close the 2 fasteners.


e.
B340871

Pull the straps to tighten them and confirm that there is a protrusion visible on each side.


f.
B338257C01
1.635,3.74 2.052,3.323 false 0.438,3.813 0.646,3.094 true 2.052,3.188 2.365,3.344 0.313,0.156 10 *1 0.354,3.813 0.667,3.969 0.313,0.156 10 *a
*1 Hog Ring Pliers
*a Cutout


Using hog ring pliers, connect the straps of the separate type front seatback cover to the separate type front seatback frame sub-assembly LH with 3 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the straps of the separate type front seatback cover.



HINT:

Install the hog rings at the cutouts if they are there.



g.
B338256C01
1.594,3.844 2.01,3.427 false 0.427,3.885 0.656,3.135 true 2,3.281 2.313,3.438 0.313,0.156 10 *1 0.354,3.875 0.667,4.031 0.313,0.156 10 *a
*1 Hog Ring Pliers
*a Cutout


Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback frame sub-assembly LH with 5 new hog rings as shown in the illustration.

NOTICE:
·

Be careful not to damage the separate type front seatback cover.

·

Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the straps of the separate type front seatback cover.



HINT:

Install the hog rings at the cutouts if they are there.



Hide 71931 18.INSTALL FRONT SEAT HEADREST SUPPORT

a.

Attach the 4 claws to install the 2 front seat headrest supports.


Hide 19.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.
B340402

Install the separate type front seatback assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.
B340401

Attach the 2 hooks.


c.

Connect the connector and attach the clamp.


d.
B340391C01
2.25,0.917 2.833,0.917 true 2.875,0.823 3.188,0.979 0.313,0.156 10 *1
*1 Fastener


w/ Front Seat Side Airbag:

i.

Attach the fastener to connect the wire harness of the front seat airbag assembly LH.


ii.
B340390C01
2,0.417 3.083,0.167 true 2.417,1.031 3.083,1.031 true 2.417,1.469 3.083,1.469 true 2.438,0.625 3.115,0.625 true 2.167,0.521 2.417,0.438 2.417,0.438 3.083,0.438 true 3.104,0.083 3.417,0.24 0.313,0.156 10 false *2 3.115,0.948 3.427,1.104 0.313,0.156 10 false *1 3.104,1.396 3.417,1.552 0.313,0.156 10 false *1 3.146,0.552 3.375,0.792 0.229,0.24 10 false *1 3.115,0.354 3.344,0.594 0.229,0.24 10 false *1
*1 Wire Harness Clamp
*2 Connector Clamp


Attach the 4 wire harness clamps and connector clamp.



e.
B340392

w/ Seat Heater System:

i.

Connect the connector.


ii.

Attach the wire harness clamp and connector clamp.



f.

Connect the rubber band.


Hide 71862 20.INSTALL FRONT INNER SEAT CUSHION SHIELD LH

a.
B341215C01
1.958,0.292 1.99,0.229 false
V100135

First
V100136

Second


Attach the 3 guides and 2 claws as indicated by the arrows in the order shown in the illustration to install the front inner seat cushion shield LH.


Hide 84920 21.INSTALL POWER SEAT SWITCH ASSEMBLY

Hide 84922 22.INSTALL FRONT POWER SEAT SWITCH (w/o Seat Memory)

Hide 84070 23.INSTALL POSITION CONTROL ECU AND SWITCH ASSEMBLY (w/ Seat Memory)

Hide 84921A 24.INSTALL RECLINING POWER SEAT SWITCH KNOB

a.

Attach the 2 claws to install the reclining power seat switch knob.


Hide 84921B 25.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

a.

Attach the 2 claws to install the slide and vertical power seat switch knob.


Hide 71812D 26.INSTALL FRONT SEAT CUSHION SHIELD LH

a.
B340382C01
0.167,0.094 0.479,0.25 0.313,0.156 10 false *A 0.188,1.333 0.5,1.49 0.313,0.156 10 false *B
*1 w/o Seat Memory
*2 w/ Seat Memory


w/o Seat Memory:

Connect the 2 connectors and attach the 3 clamps to install the front seat cushion shield LH.


b.

w/ Seat Memory:

Connect the 3 connectors and attach the 3 clamps to install the front seat cushion shield LH.


c.

Attach the 3 claws to close the cover.


d.
B341214C01
1.438,1.229 1.417,1.229 false
V100135

First
V100136

Second


Attach the 3 guides and claw as indicated by the arrows in the order shown in the illustration.


e.

Attach the clip.


Hide 71868A 27.INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD LH

a.
B341218

Attach the 2 claws, guide and clip in the direction indicated by the arrow shown in the illustration to install the front inner No. 1 seat cushion shield LH.


b.

Attach the claw and install the screw.