The door side airbag sensor LH or RH consists of a lateral deceleration sensor, etc.
If the airbag sensor assembly receives signals from the lateral deceleration sensor, it determines whether the SRS should be activated.
DTC B1690/15 or B1695/16 is stored when a malfunction is detected in the door side airbag sensor LH or RH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1690/15 | Door Side Airbag Sensor RH Malfunction | Either condition is met:
·
A door side airbag sensor RH malfunction. ·
A airbag sensor assembly malfunction. |
·
Door side airbag sensor RH ·
Airbag sensor assembly |
| B1695/16 | Door Side Airbag Sensor LH Malfunction | Either condition is met:
·
A door side airbag sensor LH malfunction. ·
A airbag sensor assembly malfunction. |
·
Door side airbag sensor LH ·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
Turn the ignition switch to ON.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1690/16 is output |
| DTC B1695/15 is output |
| DTC B1690/15 and B1695/16 are not output |
Codes other than DTC B1690/15 and B1695/16 may be output at this time, but they are not related to this check.
DTC B1690/16 is output
DTC B1695/15 is output
DTC B1690/15 and B1695/16 are not output
| *1 | Door Side Airbag Sensor LH |
| *2 | Rear Airbag Sensor RH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the door side airbag sensor RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1695/16 is output |
| DTC B1690/15 is output |
| DTC B1690/15 and B1695/16 are not output |
Codes other than DTC B1690/15 and B1695/16 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.
DTC B1695/16 is output
DTC B1690/15 is output
DTC B1690/15 and B1695/16 are not output
| *1 | Door Side Airbag Sensor RH |
| *2 | Rear Airbag Sensor LH |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Interchange the door side airbag sensor LH with RH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 90 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1695/16 is output |
| DTC B1690/15 is output |
| DTC B1690/15 and B1695/16 are not output |
Codes other than DTC B1690/15 and B1695/16 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.
DTC B1695/16 is output
DTC B1690/15 is output
DTC B1690/15 and B1695/16 are not output