Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/o Occupant Classification System)
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0049192 AIRBAG SYSTEM(w/o Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o Occupant Classification System)  B1820/55  Short in Side Squib RH Circuit  B1821/55  Open in Side Squib RH Circuit  B1822/55  Short to GND in Side Squib RH Circuit  B1823/55  Short to B+ in Side Squib RH Circuit  


DESCRIPTION

The front side squib RH circuit consists of the airbag sensor assembly and front seat airbag assembly RH.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front side squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1820/55 Short in Side Squib RH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the front side squib RH circuit during the primary check.

·

A front side squib RH malfunction.

·

A airbag sensor assembly malfunction.


·

Floor wire

·

Front seat airbag assembly RH (Front side squib RH)

·

Airbag sensor assembly


B1821/55 Open in Side Squib RH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the front side squib RH circuit for 2 seconds.

·

A front side squib RH malfunction.

·

A airbag sensor assembly malfunction.


·

Floor wire

·

Front seat airbag assembly RH (Front side squib RH)

·

Airbag sensor assembly


B1822/55 Short to GND in Side Squib RH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the front side squib RH circuit for 0.5 seconds.

·

A front side squib RH malfunction.

·

A airbag sensor assembly malfunction.


·

Floor wire

·

Front seat airbag assembly RH (Front side squib RH)

·

Airbag sensor assembly


B1823/55 Short to B+ in Side Squib RH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the front side squib RH circuit for 0.5 seconds.

·

A front side squib RH malfunction.

·

A airbag sensor assembly malfunction.


·

Floor wire

·

Front seat airbag assembly RH (Front side squib RH)

·

Airbag sensor assembly



WIRING DIAGRAM

C253326C01
4.469,4.125 4.927,4.323 0.458,0.198 10 false M24 4.469,4.25 6.604,4.438 2.135,0.188 10 false Airbag Sensor Asseembly 1.917,1.573 2.375,1.771 0.458,0.198 10 false SFR+ 4.771,2.51 5.375,2.729 0.604,0.219 10 false SFR- 4.563,1.563 4.74,1.792 0.177,0.229 10 false 9 4.479,2.417 4.729,2.667 0.25,0.25 10 false 10 2.448,1.563 2.625,1.792 0.177,0.229 10 false 1 2.448,2.417 2.625,2.646 0.177,0.229 10 false 2 4.771,1.667 5.229,1.865 0.458,0.198 10 false SFR+ 1.958,2.406 2.563,2.625 0.604,0.219 10 false SFR- 0.438,3.021 0.896,3.219 0.458,0.198 10 false Mr1 0.438,3.219 3.177,3.74 2.74,0.521 10 false Front Seat Airbag Assembly RH (Front Side Squib RH)

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT AIRBAG ASSEMBLY RH (FRONT SIDE SQUIB RH)
a.
C279673C01
0.313,1.948 0.719,2.25 0.406,0.302 2.365,2.5 2.677,2.563 false 2.26,2.698 2.542,2.896 false 2.094,0.625 2.333,0.885 0.24,0.26 10 false A 1.552,0.917 1.792,1.177 0.24,0.26 10 false C 1.333,0.917 1.573,1.177 0.24,0.26 10 false D 0.969,0.302 1.208,0.563 0.24,0.26 10 false *1 2.063,1.26 2.302,1.521 0.24,0.26 10 false *2 2.51,1.802 2.75,2.063 0.24,0.26 10 false *3 1.625,1.521 1.865,1.781 0.24,0.26 10 false *a 2.719,2.479 3.208,2.75 0.49,0.271 10 false SST 2.594,2.802 2.833,3.063 0.24,0.26 10 false *b 0.385,2 0.875,2.271 0.49,0.271 10 false Mr1
*1 Front Side Squib RH
*2 Airbag Sensor Assembly
*3 Connector C
*a Front view of wire harness connector
(to Front Side Squib RH)
*b Color: Red


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the front seat airbag assembly RH.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat airbag assembly RH (front side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output.


HINT:

Codes other than DTC B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector C.


Result:
Proceed to
OK (for Power Seat)
OK (for Manual Seat)
NG



OK (for Power Seat)

OK (for Manual Seat)

NG

2.CHECK CONNECTORS
2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly.


b.
C208251C05
0.602,0.763 0.773,0.933 0.17,0.17 10 *1 1.247,0.763 1.417,0.933 0.17,0.17 10 *2 1.72,1.622 1.89,1.792 0.17,0.17 10 *3 1.892,0.986 2.02,1.156 0.128,0.17 10 A 1.496,1.278 1.625,1.448 0.128,0.17 10 B 1.101,1.278 1.229,1.448 0.128,0.17 10 C 0.86,1.278 0.989,1.448 0.128,0.17 10 D
*1 Front Side Squib RH
*2 Floor Wire
*3 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and front seat airbag assembly RH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT SIDE SQUIB RH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT SIDE SQUIB RH CIRCUIT
a.
C279674C01
0.375,2.302 0.781,2.542 0.406,0.24 0.958,2.969 1.688,2.813 true 2.531,2.948 1.833,2.813 true 1.927,0.781 2.229,1.063 0.302,0.281 10 false A 1.583,1.063 1.885,1.344 0.302,0.281 10 false B 1.198,1.052 1.5,1.333 0.302,0.281 10 false C 0.979,1.052 1.281,1.333 0.302,0.281 10 false D 0.688,0.51 0.927,0.74 0.24,0.229 10 false *1 1.292,0.5 1.531,0.729 0.24,0.229 10 false *2 1.865,1.438 2.104,1.667 0.24,0.229 10 false *3 2.51,2.354 2.75,2.583 0.24,0.229 10 false *4 1.646,1.906 1.885,2.135 0.24,0.229 10 false *a 2.594,2.844 3.26,3.094 0.667,0.25 10 false SFR- 0.49,2.865 1.156,3.115 0.667,0.25 10 false SFR+ 0.417,2.313 0.76,2.51 0.344,0.198 10 false Mr1
*1 Front Side Squib RH
*2 Floor Wire
*3 Airbag Sensor Assembly
*4 Connector C
*a Front view of wire harness connector
(to Front Side Squib RH)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Mr1-1 (SFR+) - Body ground Ignition switch ON Below 1 V
Mr1-2 (SFR-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Mr1-1 (SFR+) - Mr1-2 (SFR-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Mr1-1 (SFR+) - Mr1-2 (SFR-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Mr1-1 (SFR+) - Body ground Always 1 MΩ or higher
Mr1-2 (SFR-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AIR BAG SENSOR ASSEMBLY

NG

REPLACE FLOOR WIRE

4.CHECK AIR BAG SENSOR ASSEMBLY
a.
C207519C02
1.563,1.615 1.865,1.938 0.302,0.323 10 *2 0.813,0.823 1,0.979 0.188,0.156 10 *1 1.021,1.25 1.156,1.417 0.135,0.167 10 D 1.177,1.25 1.313,1.417 0.135,0.167 10 C 1.708,1.042 2.01,1.365 0.302,0.323 10 A
*1 Front Side Squib RH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat airbag assembly RH and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
HINT:

Codes other than DTC B1820/55, B1821/55, B1822/55 and B1823/55 may be output at this time, but they are not related to this check.



Result:
Proceed to
DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output
DTC B1820/55, B1821/55, B1822/55 or B1823/55 is output



DTC B1820/55, B1821/55, B1822/55 or B1823/55 is not output

DTC B1820/55, B1821/55, B1822/55 or B1823/55 is output