Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM(w/o Occupant Classification System)
RM3090E _58 Vehicle Interior _008786 SUPPLEMENTAL RESTRAINT SYSTEMS _0049192 AIRBAG SYSTEM(w/o Occupant Classification System) C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM(w/o Occupant Classification System)  B1825/56  Short in Side Squib LH Circuit  B1826/56  Open in Side Squib LH Circuit  B1827/56  Short to GND in Side Squib LH Circuit  B1828/56  Short to B+ in Side Squib LH Circuit  


DESCRIPTION

The front side squib LH circuit consists of the airbag sensor assembly and front seat airbag assembly LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the front side squib LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1825/56 Short in Side Squib LH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal 5 times in the front side squib LH circuit during the primary check.

·

A front side squib LH malfunction.

·

A airbag sensor assembly malfunction.


·

No. 2 floor wire

·

Front seat airbag assembly LH (Front side squib LH)

·

Airbag sensor assembly


B1826/56 Open in Side Squib LH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects an open circuit signal in the front side squib LH circuit for 2 seconds.

·

A front side squib LH malfunction.

·

A airbag sensor assembly malfunction.


·

No. 2 floor wire

·

Front seat airbag assembly LH (Front side squib LH)

·

Airbag sensor assembly


B1827/56 Short to GND in Side Squib LH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to ground signal in the front side squib LH circuit for 0.5 seconds.

·

A front side squib LH malfunction.

·

A airbag sensor assembly malfunction.


·

No. 2 floor wire

·

Front seat airbag assembly LH (Front side squib LH)

·

Airbag sensor assembly


B1828/56 Short to B+ in Side Squib LH Circuit One of the following conditions is met:
·

The airbag sensor assembly detects a short circuit to B+ signal in the front side squib LH circuit for 0.5 seconds.

·

A front side squib LH malfunction.

·

A airbag sensor assembly malfunction.


·

No. 2 floor wire

·

Front seat airbag assembly LH (Front side squib LH)

·

Airbag sensor assembly



WIRING DIAGRAM

C253326E50
4.677,4.146 5.135,4.344 0.458,0.198 10 false N20 4.813,4.281 6.906,4.479 2.094,0.198 10 false Airbag Sensor Asseembly 1.917,1.573 2.375,1.771 0.458,0.198 10 false SFL+ 4.771,2.51 5.375,2.729 0.604,0.219 10 false SFL- 4.563,1.563 4.74,1.792 0.177,0.229 10 false 7 4.573,2.417 4.823,2.667 0.25,0.25 10 false 6 2.448,1.563 2.625,1.792 0.177,0.229 10 false 1 2.448,2.417 2.625,2.646 0.177,0.229 10 false 2 4.771,1.667 5.229,1.865 0.458,0.198 10 false SFL+ 1.958,2.406 2.563,2.625 0.604,0.219 10 false SFL- 0.438,3.021 0.896,3.219 0.458,0.198 10 false Nr1 0.438,3.219 3.177,3.74 2.74,0.521 10 false Front Seat Airbag Assembly LH (Front Side Squib LH)

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



HINT:

To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK FRONT SEAT AIRBAG ASSEMBLY LH (FRONT SIDE SQUIB LH)
a.
C279675C01
0.229,2.104 0.635,2.323 0.406,0.219 2.375,2.365 2.719,2.417 false 2.292,2.635 2.573,2.792 false 1.813,1.021 2.125,1.219 0.313,0.198 10 false A 1.292,1.292 1.604,1.49 0.313,0.198 10 false C 1.073,1.292 1.385,1.49 0.313,0.198 10 false D 0.771,0.75 1.083,0.948 0.313,0.198 10 false *1 1.896,1.344 2.208,1.542 0.313,0.198 10 false *2 1.646,1.51 1.958,1.708 0.313,0.198 10 false *a 2.396,1.719 2.708,1.917 0.313,0.198 10 false *3 2.75,2.313 3.156,2.521 0.406,0.208 10 false SST 2.625,2.719 3.031,2.927 0.406,0.208 10 false *b 0.292,2.125 0.698,2.333 0.406,0.208 10 false Nr1
*1 Front Side Squib LH
*2 Airbag Sensor Assembly
*3 Connector C
*a Front view of wire harness connector
(to Front Side Squib LH)
*b Color: Red


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the front seat airbag assembly LH.


d.

Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the front seat airbag assembly LH (front side squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188

h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188
OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTC B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



k.

Turn the ignition switch off.


l.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


m.

Disconnect SST from connector C.


Result:
Proceed to
OK (for Power Seat)
OK (for Manual Seat)
NG



OK (for Power Seat)

OK (for Manual Seat)

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Disconnect the connectors from the airbag sensor assembly.


b.
C208250C04
0.854,1.583 1.052,1.823 0.198,0.24 10 D 0.646,1.094 0.844,1.26 0.198,0.167 10 *1 1.25,1.083 1.448,1.25 0.198,0.167 10 *2 1.698,1.667 1.896,1.833 0.198,0.167 10 *3 1.083,1.583 1.292,1.802 0.208,0.219 10 C 1.5,1.583 1.708,1.813 0.208,0.229 10 B 1.906,1.344 2.104,1.531 0.198,0.188 10 A
*1 Front Side Squib LH
*2 No. 2 Floor Wire
*3 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and front seat airbag assembly LH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.



Result:
Proceed to
OK
NG



OK

3.CHECK FRONT SIDE SQUIB LH CIRCUIT

NG

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT SIDE SQUIB LH CIRCUIT
a.
C279676C01
0.323,2.146 0.708,2.396 0.385,0.25 1.063,3.177 1.625,2.823 true 2.469,3.146 1.781,2.833 true 1.917,1.083 2.177,1.365 0.26,0.281 10 false A 1.552,1.365 1.813,1.646 0.26,0.281 10 false B 1.167,1.344 1.427,1.625 0.26,0.281 10 false C 0.938,1.354 1.198,1.635 0.26,0.281 10 false D 2.625,2.229 2.885,2.51 0.26,0.281 10 false *4 0.688,0.813 0.948,1.094 0.26,0.281 10 false *1 1.281,0.813 1.542,1.094 0.26,0.281 10 false *2 1.969,1.438 2.229,1.719 0.26,0.281 10 false *3 1.625,1.948 1.885,2.229 0.26,0.281 10 false *a 0.396,2.167 0.833,2.479 0.438,0.313 10 false Nr1 0.583,3.073 1.146,3.281 0.563,0.208 10 false SFL+ 2.51,3.073 3.073,3.281 0.563,0.208 10 false SFL-
*1 Front Side Squib LH
*2 No. 2 Floor Wire
*3 Airbag Sensor Assembly
*4 Connector C
*a Front view of wire harness connector
(to Front Side Squib LH)


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Nr1-1 (SFL+) - Body ground Ignition switch ON Below 1 V
Nr1-2 (SFL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Nr1-1 (SFL+) - Nr1-2 (SFL-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DIAGNOSIS SYSTEM


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Nr1-1 (SFL+) - Nr1-2 (SFL-) Always 1 MΩ or higher



i.

Restore the released activation prevention mechanism of connector B to its original condition.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Nr1-1 (SFL+) - Body ground Always 1 MΩ or higher
Nr1-2 (SFL-) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK AIR BAG SENSOR ASSEMBLY

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK AIR BAG SENSOR ASSEMBLY
a.
C146261C12
0.854,1.115 0.854,1.5 false 0.781,1.531 0.979,1.729 0.198,0.198 10 *1 0.958,1.188 1.083,1.385 0.125,0.198 10 D 1.094,1.198 1.24,1.385 0.146,0.188 10 C 1.479,1.469 1.677,1.635 0.198,0.167 10 *2 1.656,0.948 1.802,1.135 0.146,0.188 10 A
*1 Front Side Squib LH
*2 Airbag Sensor Assembly


Connect the connectors to the front seat airbag assembly LH and airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Clear the DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 188

e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 188
OK:

DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output


HINT:

Codes other than DTC B1825/56, B1826/56, B1827/56 and B1828/56 may be output at this time, but they are not related to this check.



Result:
Proceed to
DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output
DTC B1825/56, B1826/56, B1827/56 or B1828/56 is output



DTC B1825/56, B1826/56, B1827/56 or B1828/56 is not output

DTC B1825/56, B1826/56, B1827/56 or B1828/56 is output