The front pretensioner squib RH circuit consists of the airbag sensor assembly and front seat outer belt assembly RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front pretensioner squib RH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1900/73 | Short in Front Pretensioner Squib RH Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal 5 times in the front pretensioner squib RH circuit during the primary check. ·
A front pretensioner squib RH malfunction. ·
A airbag sensor assembly malfunction. |
·
Floor wire ·
Front seat outer belt assembly RH (Front pretensioner squib RH) ·
Airbag sensor assembly |
| B1901/73 | Open in Front Pretensioner Squib RH Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects an open circuit signal in the front pretensioner squib RH circuit for 2 seconds. ·
A front pretensioner squib RH malfunction. ·
A airbag sensor assembly malfunction. |
·
Floor wire ·
Front seat outer belt assembly RH (Front pretensioner squib RH) ·
Airbag sensor assembly |
| B1902/73 | Short to GND in Front Pretensioner Squib RH Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a short circuit to ground signal in the front pretensioner squib RH circuit for 0.5 seconds. ·
A front pretensioner squib RH malfunction. ·
A airbag sensor assembly malfunction. |
·
Floor wire ·
Front seat outer belt assembly RH (Front pretensioner squib RH) ·
Airbag sensor assembly |
| B1903/73 | Short to B+ in Front Pretensioner Squib RH Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a short circuit to B+ signal in the front pretensioner squib RH circuit for 0.5 seconds. ·
A front pretensioner squib RH malfunction. ·
A airbag sensor assembly malfunction. |
·
Floor wire ·
Front seat outer belt assembly RH (Front pretensioner squib RH) ·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM(w/o Occupant Classification System)>DIAGNOSIS SYSTEM).
| *1 | Front Pretensioner Squib RH |
| *2 | Airbag Sensor Assembly |
| *3 | Connector C |
| *a | Front view of wire harness connector
(to Front Pretensioner Squib RH) |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the front seat outer belt assembly RH.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
Never connect the tester to the front seat outer belt assembly RH (front pretensioner squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output |
| DTC B1900/73, B1901/73, B1902/73 or B1903/73 is output |
Codes other than DTC B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output
DTC B1900/73, B1901/73, B1902/73 or B1903/73 is output
Disconnect the connectors from the airbag sensor assembly.
| *1 | Front Pretensioner Squib RH |
| *2 | Floor Wire |
| *3 | Airbag Sensor Assembly |
Check that the connectors (on the airbag sensor assembly side and front seat outer belt assembly RH side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Pretensioner Squib RH |
| *2 | Floor Wire |
| *3 | Airbag Sensor Assembly |
| *4 | Connector C |
| *a | Front view of wire harness connector
(to Front Pretensioner Squib RH) |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| M5-1 (R-) - Body ground | Ignition switch ON | Below 1 V |
| M5-2 (R+) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M5-1 (R-) - M5-2 (R+) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M5-1 (R-) - M5-2 (R+) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M5-1 (R-) - Body ground | Always | 1 MΩ or higher |
| M5-2 (R+) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Pretensioner Squib RH |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the front seat outer belt assembly RH and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
| Proceed to |
|---|
| DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output |
| DTC B1900/73, B1901/73, B1902/73 or B1903/73 is output |
Codes other than DTC B1900/73, B1901/73, B1902/73 and B1903/73 may be output at this time, but they are not related to this check.
DTC B1900/73, B1901/73, B1902/73 or B1903/73 is not output
DTC B1900/73, B1901/73, B1902/73 or B1903/73 is output