Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) C

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  P0335  Engine Speed Sensor Circuit (NE Circuit)  


DESCRIPTION

The crankshaft position sensor sends an engine speed signal (NE signal) to the ECM. The engine speed signal is then sent directly from the NEO terminal of the ECM to the engine stop and start ECU.

In addition, the ECM sends the engine speed value to the engine stop and start ECU via CAN communication, and the engine stop and start ECU compares the NE signal and the engine speed to check for errors in the NE signal.

If any errors are detected, the engine stop and start ECU cancels stop and start control.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0335 Engine Speed Sensor Circuit (NE Circuit) All of the following conditions continue for 10 seconds (2 trip detection logic):
·

Normal communication between the ECM and the engine stop and start ECU.

·

Engine speed (NE signal) is below 6000 rpm.

·

Difference between the NE signal that is sent directly from ECM and the engine speed that is sent via CAN is 200 rpm or higher.


Both of the following conditions continue for 2 seconds or more (1 trip detection logic):
·

Starter is operating.

·

No NE signal input.


·

Wire harness or connector

·

Crankshaft position sensor

·

ECM

·

Engine stop and start ECU


Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and wait for at least 15 seconds.


e.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227
A199262E07
3.177,2.427 3.177,3.021 false 1.198,1.146 2.417,1.438 1.219,0.292 10 false Engine Running 4.365,0.177 5.573,0.354 1.208,0.177 10 false Judgment Timing 3.49,1.729 4.302,1.906 0.813,0.177 10 false 15 seconds 6.292,2.833 6.656,3.01 0.365,0.177 10 false Time 1.333,2.385 2.417,2.615 1.083,0.229 10 false Engine Stopped 2.813,3.052 3.833,3.292 1.021,0.24 10 false Engine Started 4.115,3.302 6.313,3.51 2.198,0.208 10 false Judged Normal or Abnormal



STOP AND START SYSTEM OPERATION CHECK


HINT:

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A318769E01
5.521,2.063 5.979,2.26 0.458,0.198 10 false A66 4.323,1.844 4.635,2.042 0.313,0.198 10 false 10 5.906,2.052 6.219,2.25 0.313,0.198 10 false NE 5.521,2.542 5.979,2.74 0.458,0.198 10 false G87 5.51,3.01 5.969,3.208 0.458,0.198 10 false G87 5.521,3.49 5.979,3.688 0.458,0.198 10 false A65 5.563,2.344 5.875,2.542 0.313,0.198 10 false 15 5.563,2.813 5.875,3.01 0.313,0.198 10 false 16 5.604,3.302 5.76,3.5 0.156,0.198 10 false 8 5.875,2.542 6.49,2.74 0.615,0.198 10 false CANH 5.885,3.01 6.5,3.208 0.615,0.198 10 false CANL 5.896,3.5 6.354,3.698 0.458,0.198 10 false GND 4.313,2.063 4.771,2.26 0.458,0.198 10 false A61 5.552,1.865 5.865,2.063 0.313,0.198 10 false 10 4.313,2.542 4.771,2.74 0.458,0.198 10 false A61 4.313,3.01 4.771,3.208 0.458,0.198 10 false A61 4.375,2.323 4.531,2.521 0.156,0.198 10 false 7 4.375,2.792 4.531,2.99 0.156,0.198 10 false 6 3.802,2.542 4.417,2.74 0.615,0.198 10 false CANH 3.813,3.021 4.427,3.219 0.615,0.198 10 false CANL 3.865,2.052 4.344,2.26 0.479,0.208 10 false NEO 3.229,2.042 3.708,2.25 0.479,0.208 10 false NE+ 3.219,2.542 3.698,2.75 0.479,0.208 10 false NE- 2.833,2.063 3.292,2.26 0.458,0.198 10 false B76 2.833,1.854 3.292,2.052 0.458,0.198 10 false 103 2.823,2.542 3.281,2.74 0.458,0.198 10 false B76 2.833,2.344 3.292,2.542 0.458,0.198 10 false 102 1.781,1.917 1.938,2.115 0.156,0.198 10 false 1 1.781,2.417 1.938,2.615 0.156,0.198 10 false 2 1.781,2.813 1.938,3.01 0.156,0.198 10 false 3 1.385,2.063 1.698,2.26 0.313,0.198 10 false NE 1.385,2.531 1.865,2.74 0.479,0.208 10 false NE- 1.344,2.938 1.802,3.135 0.458,0.198 10 false GND 0.25,3.24 0.708,3.438 0.458,0.198 10 false B29 5.229,0.813 5.688,1.01 0.458,0.198 10 false G82 5.896,0.448 6.208,0.646 0.313,0.198 10 false NE 5.583,0.323 5.896,0.521 0.313,0.198 10 false 16 5.24,1 7.063,1.354 1.823,0.354 10 false Certification ECU (Smart Key ECU Assembly) 0.26,3.448 2.229,3.698 1.969,0.25 10 false Crankshaft Position Sensor 3.469,3.479 3.927,3.677 0.458,0.198 10 false ECM 5.333,3.99 7.115,4.271 1.781,0.281 10 false Engine Stop and Start ECU 0.854,4.427 4.521,4.625 3.667,0.198 10 false : CAN Communication Line 2.156,3 2.469,3.198 0.313,0.198 10 false *1 4.74,1.208 5.052,1.406 0.313,0.198 10 false *2 0.74,3.802 2.573,4 1.833,0.198 10 false *1: Shielded 0.74,4.115 5.177,4.313 4.438,0.198 10 false *2: w/ Entry and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>FREEZE FRAME DATA


PROCEDURE

1.CHECK DTC OUTPUT (ECD SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs

Powertrain > Engine > Trouble Codes
50001 61
Result:
Proceed to
No ECD system DTCs are output
ECD system DTC P0335 or P0339 is output




No ECD system DTCs are output

2.READ VALUE USING GTS (Engine Spd (NE Signal))

ECD system DTC P0335 or P0339 is output

2.READ VALUE USING GTS (Engine Spd (NE Signal))
a.

Connect the GTS to the DLC3


b.

Start the engine.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Engine Spd (NE Signal).

Powertrain > Stop and Start > Data List
Tester Display
Engine Spd (NE Signal)
50003 227 4

e.

Read the value displayed on the GTS screen.

OK:

Engine speed signal is input (the speeds displayed on the tachometer and the GTS are almost the same).



Result:
Proceed to
OK
NG



OK

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM)
3.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM)
a.

Turn the ignition switch to OFF


b.

Disconnect the A66 engine stop and start ECU connector.


c.

Disconnect the A61 ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-10 (NE) - A61-10 (NEO) Always Below 1 Ω
A66-10 (NE) - Body ground Always 10 kΩ or higher
A61-10 (NEO) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BODY GROUND)
a.

Disconnect the A65 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A65-8 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK ENGINE STOP AND START ECU (NE SIGNAL INPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK ENGINE STOP AND START ECU (NE SIGNAL INPUT)
a.

Connect an oscilloscope to the A66-10 (NE) and A65-8 (GND) terminals of the engine stop and start ECU connector.

A285225C25
2.021,0.833 2.354,1.063 0.333,0.229 3.271,0.833 3.604,1.063 0.333,0.229 1.677,2.146 2,1.729 false 3.073,2.135 2.896,1.604 false 3.323,0.885 3.781,1.083 0.458,0.198 10 false A66 2.083,0.885 2.542,1.083 0.458,0.198 10 false A65 1.531,2.188 1.99,2.385 0.458,0.198 10 false GND 3,2.188 3.458,2.385 0.458,0.198 10 false NE 0.427,0.333 0.74,0.49 0.313,0.156 10 false *a
*a Component with harness connected
(Engine Stop and Start ECU)
- -



b.

Start the engine.


c.
A278994E01
2.969,1.26 3.427,1.458 0.458,0.198 10 GND

Check the signal waveform according to the condition(s) in the table below.

Item Condition
Tester Connection A66-10 (NE) - A65-8 (GND)
Tool Setting 5 V/DIV, 2 ms/DIV
Condition Idling

Result:
Proceed to
Stuck at 0 to 1.5 V
Stuck at 8 to 14 V
Pulse generation (See waveform)




Stuck at 0 to 1.5 V

6.CHECK ENGINE STOP AND START ECU (NE TERMINAL VOLTAGE)

Stuck at 8 to 14 V

Pulse generation (See waveform)

6.CHECK ENGINE STOP AND START ECU (NE TERMINAL VOLTAGE)
a.

Disconnect the A61 ECM connector.

A285225C25
2.021,0.833 2.354,1.063 0.333,0.229 3.271,0.833 3.604,1.063 0.333,0.229 1.677,2.146 2,1.729 false 3.073,2.135 2.896,1.604 false 3.323,0.885 3.781,1.083 0.458,0.198 10 false A66 2.083,0.885 2.542,1.083 0.458,0.198 10 false A65 1.531,2.188 1.99,2.385 0.458,0.198 10 false GND 3,2.188 3.458,2.385 0.458,0.198 10 false NE 0.427,0.333 0.74,0.49 0.313,0.156 10 false *a
*a Component with harness connected
(Engine Stop and Start ECU)
- -



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A66-10 (NE) - A65-8 (GND) Ignition switch ON 8 to 14 V


Result:
Proceed to
OK
NG


HINT:

DTCs may be stored during this inspection. Check for DTCs and clear them using the GTS.




OK

NG