Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) C

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  P0617  Starter Relay Circuit High  


DESCRIPTION

When the stop and start system is activated, the engine stop and start ECU sends starter operation voltage (STA voltage) to the starter relay (ST relay) and controls the starter assembly.

If overcurrent is detected in the starter relay circuit, the engine stop and start ECU stores DTC P0617 and blinks the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P0617 Starter Relay Circuit High Both of the following conditions continue for 1 second (1 trip detection logic):
·

Ignition switch is turned to ON

·

Overcurrent to ST relay is detected.


·

Wire harness or connector

·

ST relay

·

Engine stop and start ECU


Blinking DTC stored

CONFIRMATION DRIVING PATTERN

CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



f.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more.


h.

Depress the clutch pedal and start the engine.


i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A299442E01
6.104,0.417 6.563,0.615 0.458,0.198 10 false BIN 5.74,0.417 6.198,0.615 0.458,0.198 10 false A65 5.823,0.229 5.979,0.427 0.156,0.198 10 false 7 2.708,0.563 3.167,0.76 0.458,0.198 10 false BBC 6.083,0.938 6.698,1.135 0.615,0.198 10 false CANH 1.198,0.958 1.813,1.156 0.615,0.198 10 false CANH 6.083,1.125 6.698,1.323 0.615,0.198 10 false CANL 1.198,1.135 1.813,1.333 0.615,0.198 10 false CANL 1.688,1.615 2.146,1.813 0.458,0.198 10 false A61 1.729,1.417 2.042,1.615 0.313,0.198 10 false 43 6.115,2.104 6.573,2.302 0.458,0.198 10 false CLL 5.729,4.365 6.188,4.563 0.458,0.198 10 false A65 5.74,2.104 6.198,2.302 0.458,0.198 10 false A66 5.781,1.896 6.094,2.094 0.313,0.198 10 false 28 5.74,3.083 6.198,3.281 0.458,0.198 10 false A66 5.781,2.885 6.094,3.083 0.313,0.198 10 false 21 6.104,3.073 6.563,3.271 0.458,0.198 10 false STA 6.094,4.375 6.552,4.573 0.458,0.198 10 false GND 5.813,4.156 5.969,4.354 0.156,0.198 10 false 8 3.406,3.573 5.281,4.01 1.875,0.438 10 false Clutch Start Switch Assembly (for Lower) 3.417,3.385 4.948,3.583 1.531,0.198 10 false A4*1, F2*2 4.625,2.99 4.813,3.156 0.188,0.167 10 false 1 3.76,2.99 3.938,3.208 0.177,0.219 10 false 2 1.521,3.635 2.667,4.146 1.146,0.51 10 false Ignition or Starter Switch Assembly 1.521,3.448 1.833,3.646 0.313,0.198 10 false G4 2.677,2.979 2.854,3.198 0.177,0.219 10 false 2 2.333,3.01 2.792,3.208 0.458,0.198 10 false ST2 1.615,3.01 2.073,3.208 0.458,0.198 10 false AM2 1.448,3 1.604,3.198 0.156,0.198 10 false 4 0.625,3.25 1.083,3.448 0.458,0.198 10 false AM2 0.917,2.646 1.375,2.844 0.458,0.198 10 false ECM 3.635,5.031 3.948,5.229 0.313,0.198 10 false ST 4.344,6.021 4.656,6.219 0.313,0.198 10 false ST 4.844,5.333 5,5.531 0.156,0.198 10 false 5 4.01,5.344 4.167,5.542 0.156,0.198 10 false 3 4.844,5.625 5.021,5.844 0.177,0.219 10 false 2 4.01,5.594 4.198,5.76 0.188,0.167 10 false 1 3.385,5.438 3.698,5.635 0.313,0.198 10 false B6 3.417,5.219 3.604,5.385 0.188,0.167 10 false 1 1.417,5.76 1.729,5.958 0.313,0.198 10 false C4 1.458,5.552 1.646,5.719 0.188,0.167 10 false 1 1.927,6.365 3.031,6.667 1.104,0.302 10 false Starter Assembly 0.542,6.563 1.615,6.76 1.073,0.198 10 false Battery 0.865,7.354 4.531,7.552 3.667,0.198 10 false : CAN Communication Line 2.906,7.354 3.667,7.625 0.76,0.271 10 false *1: for LHD 3.99,7.344 5.677,7.542 1.688,0.198 10 false *2: for RHD 5.917,4.906 7.01,5.427 1.094,0.521 10 false Engine Stop and Start ECU 0.031,0.042 4.99,0.281 4.958,0.24 12 false w/o Entry and Start System: 3.031,0.313 3.313,0.531 0.281,0.219 10 false 2 2.573,0.313 2.854,0.531 0.281,0.219 10 false 1 1.302,1.615 1.76,1.813 0.458,0.198 10 false STA 0.448,5.323 1.521,5.521 1.073,0.198 10 false FL MAIN

A299443E01
6.094,0.417 6.552,0.615 0.458,0.198 10 false BIN 5.74,0.417 6.198,0.615 0.458,0.198 10 false A65 5.813,0.219 5.969,0.417 0.156,0.198 10 false 7 5.74,4.375 6.198,4.573 0.458,0.198 10 false A65 6.094,4.375 6.552,4.573 0.458,0.198 10 false GND 5.802,4.167 5.958,4.365 0.156,0.198 10 false 8 6.104,2.104 6.563,2.302 0.458,0.198 10 false CLL 5.729,2.094 6.188,2.292 0.458,0.198 10 false A66 5.729,3.083 6.188,3.281 0.458,0.198 10 false A66 5.76,1.896 6.073,2.094 0.313,0.198 10 false 28 2.615,0.583 3.073,0.781 0.458,0.198 10 false BBC 6.094,3.083 6.552,3.281 0.458,0.198 10 false STA 5.771,2.875 6.083,3.073 0.313,0.198 10 false 21 0.948,2.646 1.406,2.844 0.458,0.198 10 false ECM 1.698,1.615 2.156,1.813 0.458,0.198 10 false A61 1.74,1.396 2.052,1.594 0.313,0.198 10 false 43 1.271,1.615 1.729,1.813 0.458,0.198 10 false STA 6.083,0.917 6.698,1.115 0.615,0.198 10 false CANH 1.198,0.906 1.813,1.104 0.615,0.198 10 false CANH 6.083,1.125 6.698,1.323 0.615,0.198 10 false CANL 1.208,1.104 1.823,1.302 0.615,0.198 10 false CANL 3.625,3.521 4.969,4.01 1.344,0.49 10 false Clutch Start Switch Assembly (for Lower) 3.635,3.344 5.188,3.542 1.552,0.198 10 false A4*1, F2*2 4.646,2.979 4.802,3.177 0.156,0.198 10 false 1 3.74,2.979 3.896,3.177 0.156,0.198 10 false 2 2.177,3.094 2.635,3.292 0.458,0.198 10 false STAR 2.698,2.979 2.875,3.177 0.177,0.198 10 false 5 2.26,3.448 2.719,3.646 0.458,0.198 10 false STA 2.698,3.333 2.854,3.531 0.156,0.198 10 false 7 1.615,3.083 1.927,3.281 0.313,0.198 10 false +B 1.438,2.979 1.594,3.177 0.156,0.198 10 false 2 0.677,3.25 1.135,3.448 0.458,0.198 10 false AM2 1.521,3.823 1.979,4.021 0.458,0.198 10 false G82 1.521,4.031 3.031,4.542 1.51,0.51 10 false Certification ECU (Smart Key ECU Assembly) 5.938,4.938 6.969,5.302 1.031,0.365 10 false Engine Stop and Start ECU 4.354,6.042 4.667,6.24 0.313,0.198 10 false ST 3.5,5.01 3.813,5.208 0.313,0.198 10 false ST 3.385,5.438 3.698,5.635 0.313,0.198 10 false B6 3.427,5.25 3.583,5.448 0.156,0.198 10 false 1 4,5.615 4.156,5.813 0.156,0.198 10 false 1 4.823,5.635 4.979,5.833 0.156,0.198 10 false 2 4.823,5.323 5,5.521 0.177,0.198 10 false 5 4.01,5.333 4.167,5.531 0.156,0.198 10 false 3 1.417,5.75 1.729,5.948 0.313,0.198 10 false C4 1.458,5.563 1.615,5.76 0.156,0.198 10 false 1 1.885,6.375 3.177,6.635 1.292,0.26 10 false Starter Assembly 0.521,6.604 1.594,6.802 1.073,0.198 10 false Battery 0.906,7.396 2.771,7.708 1.865,0.313 10 false : CAN Communication Line 2.927,7.396 3.865,7.615 0.938,0.219 10 false *1: for LHD 3.938,7.396 4.875,7.615 0.938,0.219 10 false *2: for RHD 0.052,0.042 4.823,0.281 4.771,0.24 12 false w/ Entry and Start System: 2.958,0.313 3.26,0.542 0.302,0.229 10 false 2 2.5,0.313 2.802,0.542 0.302,0.229 10 false 1 0.448,5.365 1.521,5.563 1.073,0.198 10 false FL MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>FREEZE FRAME DATA


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - BBC FUSE)

OK

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)
a.

Disconnect the A65 and A66 engine stop and start ECU connectors.


b.

Disconnect the A61 ECM connector.


c.

w/ Entry and Start System:

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the A4*1 or F2*2 clutch start switch assembly (for lower) connector.

*1: for LHD

*2: for RHD



e.

Remove the ST relay from No. 2 engine room relay block and junction block assembly.


f.

Remove the BBC fuse from engine room relay block and junction block assembly.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - ST relay terminal 2 Always Below 1 Ω
A66-21 (STA) - Body ground Always 10 kΩ or higher
ST relay terminal 2 - Body ground Always 10 kΩ or higher
A65-7 (BIN) - A66-21 (STA) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU
a.

Disconnect the engine stop and start ECU connector.

A295480C04
1.5,0.583 1.917,0.833 0.417,0.25 3.167,0.583 3.583,0.833 0.417,0.25 5,0.583 5.417,0.833 0.417,0.25 3.031,2.146 3.323,1.323 false 1.469,2.104 1.615,1.594 false 0.115,0.052 0.427,0.208 0.313,0.156 10 *a 1.583,0.625 1.896,0.823 0.313,0.198 10 A65 3.25,0.625 3.563,0.823 0.313,0.198 10 A66 5.073,0.635 5.385,0.833 0.313,0.198 10 G87 2.854,2.177 3.313,2.375 0.458,0.198 10 STA 1.302,2.125 1.76,2.323 0.458,0.198 10 GND
*a Component without harness connected
(Engine Stop and Start ECU)
- -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - A65-8 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT RELAY (ST RELAY)

NG

4.INSPECT RELAY (ST RELAY)

Result:
Proceed to
OK
NG



OK

NG

REPLACE RELAY (ST RELAY)