Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) C

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  P1540  Brake Booster Sensor Circuit (Open or Short)  


DESCRIPTION

The engine stop and start ECU determines changes in the brake booster assembly pressure based on the voltage signal received from the vacuum sensor assembly in the brake booster assembly.

If the engine stop and start ECU judges that the signal received from the vacuum sensor assembly is abnormal, it stores DTC P1540 and blinks the stop and start cancel indicator light.

A280541E05
2.875,1.052 3.083,0.333 3.083,0.333 3.333,0.333 true 2.927,2.76 2.917,3.167 true 0.063,0.052 1.896,0.25 1.833,0.198 10 false Vacuum Sensor Voltage: 0.833,0.51 1.688,0.677 0.854,0.167 10 false Voltage (V) 0.938,0.781 1.292,1.01 0.354,0.229 10 false 5.0 0.938,1.188 1.292,1.385 0.354,0.198 10 false 4.5 0.875,2.49 1.281,2.667 0.406,0.177 10 false 0.27 1.031,2.896 1.313,3.083 0.281,0.188 10 false 0 2.667,1.792 3.875,1.99 1.208,0.198 10 false Normal Range 3.375,0.24 4.677,0.458 1.302,0.219 10 false Abnormal Range 2.531,3.177 4,3.5 1.469,0.323 10 false Abnormal Range

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1540 Brake Booster Sensor Circuit (Open or Short) The following conditions continue for 2 seconds or more (1 trip detection logic):
·

Open or short in vacuum sensor assembly circuit

·

Ignition switch is turned to ON


·

Vacuum sensor assembly

·

Engine stop and start ECU

·

Wire harness or connector


Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and allow it to idle for 15 seconds or more.


e.

Stop the engine and turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure.

Powertrain > Stop and Start > Data List
Tester Display
Brake Boost Pressure
50003 227 61

h.

While depressing the brake pedal several times, check that the Brake Boost Pressure value changes.


i.

Check that DTCs are not output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



WIRING DIAGRAM

A285528E06
2.167,0.729 2.688,0.958 0.521,0.229 10 VC 2.177,1.198 2.635,1.427 0.458,0.229 10 PB 2.198,1.646 2.646,1.958 0.448,0.313 10 E2 1.323,2.115 1.771,2.333 0.448,0.219 10 A60 1.323,2.26 3.031,2.563 1.708,0.302 10 Vacuum Sensor Assembly 2.469,0.635 3.031,0.938 0.563,0.302 10 3 2.469,1.094 2.802,1.365 0.333,0.271 10 2 2.469,1.552 2.833,1.823 0.365,0.271 10 1 4.49,0.625 4.969,0.906 0.479,0.281 10 14 4.49,1.073 4.833,1.313 0.344,0.24 10 13 4.552,1.552 4.771,1.792 0.219,0.24 10 3 4.75,0.729 5.344,1.01 0.594,0.281 10 BRVC 4.75,1.188 5.188,1.417 0.438,0.229 10 PB 4.75,1.656 5.333,2.021 0.583,0.365 10 BRE2 4.594,2.125 4.875,2.333 0.281,0.208 10 A66 4.583,2.281 6.573,2.5 1.99,0.219 10 Engine Stop and Start ECU

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION



HINT:
·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>FREEZE FRAME DATA



PROCEDURE

1.CHECK VACUUM SENSOR ASSEMBLY (PB TERMINAL VOLTAGE)
A347656C01
3.188,0.896 3.635,1.115 0.448,0.219 3.896,1.542 4,0.667 4,0.667 4.167,0.667 true 3.979,1.708 4,2.417 4,2.417 4.167,2.417 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 4.219,0.604 4.833,0.802 0.615,0.198 10 false BRE2 3.281,0.927 3.74,1.125 0.458,0.198 10 false A66 4.208,2.344 4.521,2.542 0.313,0.198 10 false PB
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-13 (PB) - A66-3 (BRE2) Ignition switch ON Higher than 0.6 V or below 4.7 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - VACUUM SENSOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - VACUUM SENSOR ASSEMBLY)
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the A60 vacuum sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-13 (PB) - A60-2 (PB) Always Below 1 Ω
A66-14 (BRVC) - A60-3 (VC) Always Below 1 Ω
A66-3 (BRE2) - A60-1 (E2) Always Below 1 Ω
A66-13 (PB) - Body ground Always 10 kΩ or higher
A66-14 (BRVC) - Body ground Always 10 kΩ or higher
A66-3 (BRE2) - Body ground Always 10 kΩ or higher
A60-2 (PB) - Body ground Always 10 kΩ or higher
A60-3 (VC) - Body ground Always 10 kΩ or higher
A60-1 (E2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU (BRVC TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK ENGINE STOP AND START ECU (BRVC TERMINAL VOLTAGE)
A347656C03
3.188,0.896 3.635,1.115 0.448,0.219 3.896,1.542 4,0.667 4,0.667 4.167,0.667 true 3.896,1.708 3.917,2.417 3.917,2.417 4.083,2.417 true 0.156,0.104 0.469,0.302 0.313,0.198 10 false *a 4.219,0.604 4.833,0.802 0.615,0.198 10 false BRE2 3.281,0.927 3.74,1.125 0.458,0.198 10 false A66 4.135,2.354 4.802,2.531 0.667,0.177 10 false BRVC
*a Component with harness connected
(Engine Stop and Start ECU)
- -


a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A66-14 (BRVC) - A66-3 (BRE2) Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG



OK

4.REPLACE VACUUM SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.REPLACE VACUUM SENSOR ASSEMBLY
a.

Replace the vacuum sensor assembly.

Click hereEngine / Hybrid System>STOP AND START>VACUUM SENSOR ASSEMBLY>REMOVAL


Result:
Proceed to
NEXT



NEXT

5.CHECK DTC OUTPUT
5.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Trouble Codes.


e.

Check that no DTCs are output.

Powertrain > Stop and Start > Trouble Codes
50001 227
Result:
Result Proceed to
DTCs are not output A
DTC P1540 is output B




A

END

B