Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) C

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  P1545  Starter Maintenance  


DESCRIPTION

When the number of starter operations reaches the maximum number, the engine stop and start ECU stores DTC P1545 and blinks the stop and start cancel indicator light. When the STA signal detected by the ECM and by the engine stop and start ECU do not match, the engine stop and start ECU stores DTC P1545 and blinks the stop and start cancel indicator light.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1545 Starter Maintenance The following conditions are met (1 trip detection logic):
·

The number of starter operations reaches the specified limit.

·

Ignition switch is turned to ON


Both of the following conditions continue for 2 seconds or more (1 trip detection logic):
·

Normal communication with the ECM.

·

STA signals detected by the ECM and the engine stop and start ECU do not match.


·

Wire harness or connector

·

ST relay

·

Engine stop and start ECU

·

Starter assembly

·

ECM


Blinking DTC stored

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

d.

Start the engine and warm it up.


e.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



f.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


g.

Keep the engine stopped by stop and start control for 1 second or more.


h.

Depress the clutch pedal and start the engine.


i.

Check that no DTCs are output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


HINT:

When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).


a.

Start the engine and warm it up.


b.

Turn the air conditioning system off.


c.

Drive the vehicle at 7 km/h (4.3 mph) or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.



d.

Stop the vehicle, move the shift lever to neutral and release the clutch pedal.


e.

Allow the engine to stop by stop and start control.


f.

Depress the clutch pedal and start the engine.



CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the starter assembly, perform initialization of the number of starter operations stored in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION

·

Inspect the fuses for circuits related to this system before performing the following procedure.



HINT:
·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR

·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>FREEZE FRAME DATA



PROCEDURE

1.READ VALUE USING GTS (STARTER OPERATION #)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Starter Operation #.

Powertrain > Stop and Start > Data List
Tester Display
Starter Operation #
50003 227 56

e.

Read the Starter Operation # value displayed on the GTS.

Result:
Proceed to
Below 368000
368000 or more




Below 368000

2.READ VALUE USING GTS (STARTER SIGNAL)

368000 or more

8.REPLACE STARTER ASSEMBLY
2.READ VALUE USING GTS (STARTER SIGNAL)
a.

Enter the following menus: Powertrain / Engine and ECT / Data List / Starter Signal.

Powertrain > Engine > Data List
Tester Display
Starter Signal
50003 61 193

b.

Depress the clutch pedal fully.


c.

Read the values displayed on the GTS when the ignition switch is turned to ON and START.

OK:
Tester Display Switch Condition Normal Condition
Starter Signal Ignition switch ON OFF
Ignition switch START ON



Result:
Proceed to
OK
NG



OK

3.CHECK ENGINE STOP AND START ECU (STA TERMINAL VOLTAGE)

NG

GO TO ECD SYSTEM (STARTER SIGNAL CIRCUIT)

3.CHECK ENGINE STOP AND START ECU (STA TERMINAL VOLTAGE)
a.

Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

HINT:

If battery voltage drops below 8 V when cranking, CAN communication may be interrupted.


A285225C27
3.198,0.896 3.552,1.135 0.354,0.24 2.813,2.25 3.375,1.708 false 0.427,0.354 0.74,0.552 0.313,0.198 10 *a 3.26,0.938 3.719,1.135 0.458,0.198 10 A66 2.656,2.292 3.115,2.49 0.458,0.198 10 STA
*a Component with harness connected
(Engine Stop and Start ECU)
- -


Standard Voltage:
Tester Connection Condition Specified Condition
A66-21 (STA) - Body ground Ignition switch ON 0 to 1.5 V
Cranking 6 to 14 V



Result:
Proceed to
NG
OK



NG

4.INSPECT RELAY (ST RELAY)

OK

4.INSPECT RELAY (ST RELAY)

Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)

NG

REPLACE RELAY (ST RELAY)

5.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ST RELAY)
a.

w/ Entry and Start System:

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A66 engine stop and start ECU connector.


c.

Disconnect the A61 ECM connector.


d.

Disconnect the A4*1 or F2*2 clutch start switch assembly (for lower) connector.

*1: for LHD

*2: for RHD



e.

Remove the ST relay from No. 2 engine room relay block and junction block assembly.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - ST relay terminal 2 Always Below 1 Ω
A66-21 (STA) - Body ground Always 10 kΩ or higher
ST relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - CLUTCH START SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - CLUTCH START SWITCH ASSEMBLY)
a.

w/ Entry and Start System:

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A66 engine stop and start ECU connector.


c.

Disconnect the A61 ECM connector.


d.

Disconnect the A4*1 or F2*2 clutch start switch assembly (for lower) connector.

*1: for LHD

*2: for RHD



e.

Remove the ST relay from No. 2 engine room relay block and junction block assembly.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD:
Tester Connection Condition Specified Condition
A66-21 (STA) - A4-1 Always Below 1 Ω
A4-1 - Body ground Always 10 kΩ or higher

for RHD:
Tester Connection Condition Specified Condition
A66-21 (STA) - F2-1 Always Below 1 Ω
F2-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ECM)
a.

w/ Entry and Start System:

Disconnect the G82 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the A66 engine stop and start ECU connector.


c.

Disconnect the A61 ECM connector.


d.

Disconnect the A4*1 or F2*2 clutch start switch assembly (for lower) connector.

*1: for LHD

*2: for RHD



e.

Remove the ST relay from No. 2 engine room relay block and junction block assembly.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-21 (STA) - A61-43 (STA) Always Below 1 Ω
A61-43 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE STARTER ASSEMBLY
a.

Replace the starter assembly

Click hereEngine / Hybrid System>1AD-FTV STARTING>STARTER>REMOVAL

HINT:
·

When replacing a starter assembly that has exceeded the specified number of operations, other related parts may also be worn. Replace the ST relay and related fuses at the same time.

·

Clear the number of starter operations by performing "Starter Exchange" using the GTS.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION




Result:
Proceed to
NEXT



NEXT

END