There are 2 clutch pedal switches for the clutch pedal. The clutch switch assembly (for upper) is used for stopping and restarting of the engine by stop and start control. During the stop and start control, the clutch start switch assembly (for lower) is used only when the clutch switch assembly (for upper) is stuck on or the fail-safe function is activated.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory |
|---|---|---|---|---|---|
| P1862 | Clutch Control System 2 | Both of the following conditions continue for 0.5 seconds or more (1 trip detection logic):
·
Clutch start switch assembly (for lower) is on. ·
Clutch switch assembly (for upper) is on. |
·
Clutch start switch assembly (for lower) ·
Clutch switch assembly (for upper) ·
Wire harness or connector ·
Engine stop and start ECU |
Blinking | DTC stored |
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR
CONFIRMATION AFTER TROUBLESHOOTING
When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).
Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR
Start the engine.
Fully depress the clutch pedal for 1 second or more. Release the clutch pedal and wait for at least 1 second.
Repeat the previous step 3 times.
Check that no DTCs are output.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR
STOP AND START SYSTEM OPERATION CHECK
When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).
Start the engine and warm it up.
Turn the air conditioning system off.
Drive the vehicle at 7 km/h (4.3 mph) or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Stop the vehicle, move the shift lever to neutral and release the clutch pedal.
Allow the engine to stop by stop and start control
Depress the clutch pedal and start the engine.
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION
After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>REGISTRATION
DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>DTC CHECK / CLEAR
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM(for 1AD-FTV)>FREEZE FRAME DATA
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Data List / Clutch Upper SW and Clutch Lower SW.
| Tester Display |
|---|
| Clutch Upper SW |
| Clutch Lower SW |
Depress the clutch pedal and read the values displayed on the GTS.
| Tester Display | Condition | Normal Condition |
|---|---|---|
| Clutch Upper SW | Fully Depressed | OFF |
| Clutch Lower SW | Fully Depressed | ON |
| Clutch Upper SW | Fully Released | ON |
| Clutch Lower SW | Fully Released | OFF |
| Proceed to |
|---|
| NG |
| OK |
NG
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Inspect the clutch start switch assembly (for lower).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the clutch switch assembly (for upper).
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A66 engine stop and start ECU connector.
Disconnect the A4*1 or F2*2 clutch start switch assembly (for lower) connector.
*1: for LHD
*2: for RHD
w/ Entry and Start System:
Disconnect the G82 certification ECU (smart key ECU assembly) connector.
w/o Entry and Start System:
Disconnect the G4 ignition or starter switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A66-28 (CLL) - A4-2 | Always | Below 1 Ω |
| A66-28 (CLL) - Body ground | Always | 10 kΩ or higher |
| A4-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A66-28 (CLL) - F2-2 | Always | Below 1 Ω |
| A66-28 (CLL) - Body ground | Always | 10 kΩ or higher |
| F2-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A66 engine stop and start ECU connector.
Disconnect the A1*1 or F1*2 clutch switch assembly (for upper) connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A66-11 (CLU) - A1-2 | Always | Below 1 Ω |
| A66-11 (CLU) - Body ground | Always | 10 kΩ or higher |
| A1-2 - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A66-11 (CLU) - F1-2 | Always | Below 1 Ω |
| A66-11 (CLU) - Body ground | Always | 10 kΩ or higher |
| F1-2 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG