Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) J

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine stop and start ECU detects open/close of the engine hood based on a signal received from the engine hood courtesy switch that is built into the hood lock assembly.

·

The engine stop and start ECU prohibits starting of the engine by stop and start control and stalls the engine if the clutch pedal is depressed with the engine hood open while the engine is stopped by stop and start control.

·

The engine stop and start ECU permits starting of the engine by stop and start control if the engine hood is opened with the clutch pedal depressed while the engine is stopped by stop and start control.


WIRING DIAGRAM

A287084E11
3.458,0.875 4.031,1.094 0.573,0.219 10 false 1 1.76,1.531 2.521,1.823 0.76,0.292 10 false A50 1.76,1.677 3.646,2.135 1.885,0.458 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 5.354,1.823 5.875,2 0.521,0.177 10 false A66 5.406,0.938 5.792,1.125 0.385,0.188 10 false 7 5.604,1.052 6.281,1.365 0.677,0.313 10 false BNT1 5.344,1.99 7.083,2.292 1.74,0.302 10 false Engine Stop and Start ECU 1.875,0.896 2.302,1.104 0.427,0.208 10 false 2 3.156,1.031 3.313,1.229 0.156,0.198 10 false + 2.167,1.042 2.323,1.24 0.156,0.198 10 false E

PROCEDURE

1.READ VALUE USING GTS (HOOD COURTESY SWITCH)
NOTICE:

Before performing this step, check that the engine hood can be opened by pulling the hood lock control cable.


a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Hood Courtesy Switch.

Powertrain > Stop and Start > Data List
Tester Display
Hood Courtesy Switch
50003 227 8

e.

Read the value displayed on the GTS when the engine hood is opened and closed.

OK:
Tester Display Condition Normal Condition
Hood Courtesy Switch Engine hood is closed ON
Engine hood is open OFF



Result:
Proceed to
NG
OK



NG

2.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
a.

Inspect the engine hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)
a.

Disconnect the A50 engine hood courtesy switch (hood lock assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A50-2 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY))
a.

Disconnect the A66 engine stop and start ECU connector.


b.

Disconnect the A50 engine hood courtesy switch (hood lock assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A66-7 (BNT1) - A50-1 (+) Always Below 1 Ω
A66-7 (BNT1) - Body ground Always 10 kΩ or higher
A50-1 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR