Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM(for 1AD-FTV) › 2012.12–2015.10
RM3090E _51 Engine / Hybrid System _009049 STOP AND START _0049492 STOP AND START SYSTEM(for 1AD-FTV) J

STOP AND START  STOP AND START SYSTEM(for 1AD-FTV)  Stop and Start Cancel Switch Circuit  


DESCRIPTION

Stop and start control can be disabled by pressing the stop and start system cancel switch (combination switch assembly). The stop and start system cancel switch (combination switch assembly) is a momentary-type switch that switches between on and off when the switch is pressed. While stop and start control is disabled, the stop and start cancel indicator light is illuminated to inform the driver.

WIRING DIAGRAM

A287084E12
3.417,0.938 3.813,1.177 0.396,0.24 10 2 1.948,0.938 2.365,1.167 0.417,0.229 10 4 1.646,1.542 2.229,1.823 0.583,0.281 10 G70 1.646,1.708 4.031,2.167 2.385,0.458 10 Stop and Start System Cancel Switch (Combination Switch Assembly) 5.365,1.833 5.833,2.031 0.469,0.198 10 G87 5.333,0.938 5.688,1.24 0.354,0.302 10 23 5.604,1.042 6.167,1.313 0.563,0.271 10 ECAN 5.354,1.99 7.104,2.302 1.75,0.313 10 Engine Stop and Start ECU

PROCEDURE

1.READ VALUE USING GTS (CANCEL SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Cancel Switch.


e.

Read the value when the stop and start system cancel switch (combination switch assembly) is pressed.

OK:
Tester Display Condition Normal Condition
Cancel Switch Stop and start system cancel switch (combination switch assembly) is pressed ON
Stop and start system cancel switch (combination switch assembly) is not press OFF



Result:
Proceed to
NG
OK



NG

2.INSPECT STOP AND START SYSTEM CANCEL SWITCH (COMBINATION SWITCH ASSEMBLY)

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.INSPECT STOP AND START SYSTEM CANCEL SWITCH (COMBINATION SWITCH ASSEMBLY)
a.

Inspect the stop and start system cancel switch (combination switch assembly).

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM CANCEL SWITCH ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (STOP AND START SYSTEM CANCEL SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE COMBINATION SWITCH ASSEMBLY (STOP AND START SYSTEM CANCEL SWITCH)

3.CHECK HARNESS AND CONNECTOR (STOP AND START SYSTEM CANCEL SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the G70 stop and start system cancel switch (combination switch assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G70-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - STOP AND START SYSTEM CANCEL SWITCH (COMBINATION SWITCH ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - STOP AND START SYSTEM CANCEL SWITCH (COMBINATION SWITCH ASSEMBLY))
a.

Disconnect the G87 engine stop and start ECU connector.


b.

Disconnect the G70 stop and start system cancel switch (combination switch assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G87-23 (ECAN) - G70-2 Always Below 1 Ω
G87-23 (ECAN) - Body ground Always 10 kΩ or higher
G70-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR