Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for LHD) › 2012.12–2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0048454 CAN COMMUNICATION SYSTEM(for LHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for LHD)  Audio Receiver Assembly Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area

*: w/ Stop and Start System

Audio Receiver Assembly Communication Stop Mode Either condition is met:
·

"Display and Navigation (AVN1)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Audio Receiver Assembly Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside radio and display receiver assembly

·

Radio and display receiver assembly CAN branch wire or connector

·

Radio and display receiver assembly

·

Engine stop and start ECU*



For vehicles with a radio and display type.


WIRING DIAGRAM

C277479E02
0.25,7.052 4.375,7.25 4.125,0.198 10 *1: w/o Stop and Start System 0.25,7.385 4.375,7.583 4.125,0.198 10 *2: w/ Stop and Start System 5.25,7.125 6.948,7.479 1.698,0.354 10 Radio and Display Receiver Assembly 0.333,1.552 2,1.75 1.667,0.198 10 G130 0.333,1.719 2.5,1.917 2.167,0.198 10 No. 2 CAN Junction Connector 0.583,2.385 2.75,2.583 2.167,0.198 10 from IG1 NO.1 Relay 2.823,2.219 3.74,2.667 0.917,0.448 10 ECU-IG NO.2 1.094,3.198 3.26,3.396 2.167,0.198 10 from Battery 2.969,3.052 3.885,3.5 0.917,0.448 10 RADIO 3.042,5.208 3.958,5.656 0.917,0.448 10 ACC 0.875,5.375 2.208,5.625 1.333,0.25 10 from ACC Relay 3.583,3.083 4.5,3.531 0.917,0.448 10 *1 2.917,3.719 3.833,4.167 0.917,0.448 10 *2 2.917,4.219 3.833,4.667 0.917,0.448 10 *2 3.583,5.219 4.5,5.667 0.917,0.448 10 *1 0.417,4.667 1.75,4.917 1.333,0.25 10 G87 0.417,4.833 3.083,5.083 2.667,0.25 10 Engine Stop and Start ECU*2 1.667,3.75 2.583,4.198 0.917,0.448 10 2 1.667,4.219 2.583,4.667 0.917,0.448 10 3 1.24,3.833 2.156,4.281 0.917,0.448 10 BO1 1.25,4.333 2.167,4.781 0.917,0.448 10 ACO 5.667,4.365 6.583,4.813 0.917,0.448 10 ACC1 5.667,3.208 6.583,3.656 0.917,0.448 10 +B1 5.667,6.219 6.583,6.667 0.917,0.448 10 GND1 5.667,2.385 6.583,2.833 0.917,0.448 10 IG 1.667,0.5 2.583,0.948 0.917,0.448 10 1 1.667,1.083 2.583,1.531 0.917,0.448 10 2 5.667,1.219 6.583,1.667 0.917,0.448 10 CANL 5.667,0.635 6.583,1.083 0.917,0.448 10 CANH 5.229,0.354 6.146,0.802 0.917,0.448 10 9 5.198,0.938 6.115,1.385 0.917,0.448 10 10 5.24,5.938 6.156,6.385 0.917,0.448 10 7 5.25,4.104 6.167,4.552 0.917,0.448 10 3 5.25,2.938 6.167,3.385 0.917,0.448 10 4 5.229,2.115 6.146,2.563 0.917,0.448 10 1 5.125,6.198 6.042,6.646 0.917,0.448 10 G141 5.135,4.354 6.052,4.802 0.917,0.448 10 G141 5.125,3.198 6.042,3.646 0.917,0.448 10 G141 5.125,2.375 6.042,2.823 0.917,0.448 10 G143 5.135,1.198 6.052,1.646 0.917,0.448 10 G143 5.125,0.615 6.042,1.063 0.917,0.448 10 G143

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 60 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for LHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE)
a.
E140414C05
1.469,0.417 1.969,0.698 0.5,0.281 2.083,1.469 2.25,2 2.25,2 2.5,2 true 1.938,1.469 1.833,2 1.833,2 1.667,2 true 0.083,0.083 0.396,0.24 0.313,0.156 10 *a 2.552,1.906 3.167,2.104 0.615,0.198 10 CANL 1.24,1.917 1.854,2.115 0.615,0.198 10 CANH 1.542,0.469 2,0.667 0.458,0.198 10 G143
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G143-9 (CANH) - G143-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C277477C02
1.5,0.208 1.938,0.448 0.438,0.24 1.542,1.813 1.979,2.052 0.438,0.24 0.969,2.594 0.708,2.417 0.708,2.417 0.542,2.417 true 2.104,1.479 1.854,1.479 1.854,1.479 1.667,1.146 true 0.365,2.344 0.823,2.542 0.458,0.198 10 IG 2.146,1.406 2.688,1.635 0.542,0.229 10 GND1 0.125,0.135 0.583,0.333 0.458,0.198 10 *a 1.542,0.25 2,0.448 0.458,0.198 10 G141 1.583,1.854 2.042,2.052 0.458,0.198 10 G143
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the radio and display receiver assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G143-1 (IG) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G141-7 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - BATTERY)
a.
C277478C02
1.448,0.26 1.885,0.542 0.438,0.281 2.333,1.167 2.5,1.333 2.5,1.333 2.75,1.333 true 2.083,1.083 2.333,0.833 2.333,0.833 2.583,0.833 true 0.073,0.063 0.531,0.26 0.458,0.198 10 *a 1.51,0.323 1.969,0.521 0.458,0.198 10 G141 2.625,0.75 3.083,0.948 0.458,0.198 10 ACC1 2.792,1.25 3.25,1.448 0.458,0.198 10 +B1
*a Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G141-4 (+B1) - Body ground Always 11 to 14 V
G141-3 (ACC1) - Body ground Ignition switch ACC 11 to 14 V



Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG (w/ Stop and Start System)

4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ENGINE STOP AND START ECU)
4.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - ENGINE STOP AND START ECU)
a.

Disconnect the G87 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G141-4 (+B1) - G87-2 (BO1) Always Below 1 Ω
G141-3 (ACC1) - G87-3 (ACO) Always Below 1 Ω
G141-4 (+B1) - Body ground Always 10 kΩ or higher
G141-3 (ACC1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR