Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(for RHD) › 2012.12–2015.10
RM3090E _57 Power Source / Network _008434 NETWORKING _0050193 CAN COMMUNICATION SYSTEM(for RHD) J

NETWORKING  CAN COMMUNICATION SYSTEM(for RHD)  Power Steering ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptoms Trouble Area

*: w/ Stop and Start System

Power Steering ECU Communication Stop Mode Either condition is met:
·

"Power Steering (EPS)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Power Steering ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source or inside power steering ECU assembly

·

Power steering ECU assembly CAN branch wire or connector

·

Power steering ECU assembly

·

Engine stop and start ECU*



WIRING DIAGRAM

C277465E02
5.365,6.031 6.667,6.375 1.302,0.344 10 false Power Steering ECU Assembly 5.615,3.573 6.917,3.917 1.302,0.344 10 false IG 5.615,5.156 6.917,5.5 1.302,0.344 10 false PGND 5.615,2.74 6.917,3.083 1.302,0.344 10 false PIG 5.615,1.573 6.917,1.917 1.302,0.344 10 false CANL 5.615,0.99 6.917,1.333 1.302,0.344 10 false CANH 5.188,0.979 6.49,1.323 1.302,0.344 10 false h1 5.198,1.573 6.5,1.917 1.302,0.344 10 false h1 5.198,2.75 6.5,3.094 1.302,0.344 10 false h2 5.198,3.583 6.5,3.927 1.302,0.344 10 false h1 5.188,5.125 6.49,5.469 1.302,0.344 10 false h2 1.667,1.417 2.969,1.76 1.302,0.344 10 false 2 1.667,0.833 2.969,1.177 1.302,0.344 10 false 1 0.333,1.917 2.583,2.167 2.25,0.25 10 false G155 0.344,2.073 2.594,2.323 2.25,0.25 10 false No. 2 CAN Junction Connector 1.656,3.448 3.906,3.698 2.25,0.25 10 false 12 1.229,3.583 3.479,3.833 2.25,0.25 10 false IGO1 0.5,4.083 2.75,4.333 2.25,0.25 10 false G87 0.5,4.25 2.75,4.5 2.25,0.25 10 false Engine Stop and Start ECU*1 0.333,5.917 2.583,6.167 2.25,0.25 10 false *1: w/ Stop and Start System 0.333,6.25 2.583,6.5 2.25,0.25 10 false *2: w/o Stop and Start System 3.417,3.417 3.833,3.75 0.417,0.333 10 false *1 4.833,4 5.25,4.333 0.417,0.333 10 false *2 3.813,4.531 4.396,4.698 0.583,0.167 10 false EPS-IG 1.75,4.698 4,4.948 2.25,0.25 10 false from IG1 NO.1 Relay 5.198,3.323 6.5,3.667 1.302,0.344 10 false 1 5.198,2.5 6.5,2.844 1.302,0.344 10 false 1 5.24,4.875 6.542,5.219 1.302,0.344 10 false 2 5.198,1.323 6.5,1.667 1.302,0.344 10 false 8 5.198,0.74 6.5,1.083 1.302,0.344 10 false 4 4.167,2.583 5.469,2.927 1.302,0.344 10 false EPS 2.198,2.75 3.5,3.094 1.302,0.344 10 false from Battery

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

DTC check procedure: Turn the ignition switch to ON and wait at least 12 seconds.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(for RHD)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE)
a.
C268317C01
2.438,1.167 2.844,1.469 0.406,0.302 1.458,1.271 1.26,0.979 1.26,0.979 1.052,0.979 true 1.042,1.781 1.292,1.781 1.292,1.781 1.458,1.427 true 0.063,0.052 0.375,0.208 0.313,0.156 10 *a 2.552,1.24 2.865,1.396 0.313,0.156 10 h1 0.646,0.896 1.146,1.104 0.5,0.208 10 CANH 0.646,1.698 1.146,1.906 0.5,0.208 10 CANL
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the power steering ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h1-4 (CANH) - h1-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE POWER STEERING ECU ASSEMBLY CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY AND BODY GROUND)
a.
C277464C01
1.49,0.208 1.917,0.448 0.427,0.24 0.729,1.833 0.979,1.833 0.979,1.833 1.292,1.292 true 2.75,1.833 2.469,1.833 2.469,1.833 2.188,1.292 true 0.104,0.094 0.417,0.25 0.313,0.156 10 *a 1.615,0.26 1.927,0.458 0.313,0.198 10 h2 0.406,1.75 0.719,1.948 0.313,0.198 10 PIG 2.823,1.76 3.281,1.969 0.458,0.208 10 PGND
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Disconnect the power steering ECU assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
h2-1 (PIG) - Body ground Always 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h2-2 (PGND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - BATTERY)
a.
C268317C02
0.313,1.188 0.719,1.49 0.406,0.302 1.969,1.25 2.281,0.969 2.281,0.969 2.521,0.969 true 0.063,0.052 0.375,0.208 0.313,0.156 10 *a 0.438,1.26 0.75,1.417 0.313,0.156 10 h1 2.563,0.875 3.063,1.083 0.5,0.208 10 IG
*a Rear view of wire harness connector
(to Power Steering ECU Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
h1-1 (IG) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG (w/ Stop and Start System)

4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - ENGINE STOP AND START ECU)
4.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU ASSEMBLY - ENGINE STOP AND START ECU)
a.

Disconnect the G87 engine stop and start ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
h1-1 (IG) - G87-12 (IGO1) Always Below 1 Ω
h1-1 (IG) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR